Manual

BREAK-IN OF THE PUMP \ RODAGE DE LA POMPE \ MARCHA DE LA BOMBA
[
BREAK-IN OF THE PUMP
1. Open the petcock (see B). Turn in the counterclockwise
direction.
2. Plug in the power cord.
3. Press the ontoff button to the ON position (the on/off
icon will show in the top left corner of the display) (see
C). The compressor will start. Allow the compressor to run
for 15 minutes, to break in the internal parts.
NOTE: After about 15 minutes, If the unit does not operate
properly, SHUT DOWN IMMEDIATELY, and contact
Product Service.
4. After about 15 minutes, press the on/off button to the OFF
position (the on/off icon will no longer be visible in the
top left corner of the display).
5. Close the petcock (see D). Turn in the clockwise direction.
6. Press the on/off button to the ON position. The compressor
will start and fill the tank to the kick-out pressure and stop.
NOTE: As compressed air is used, the pressure switch will
restart the motor automatically.
NOTE: During the initial break-in cycle, there will be a slight
electrical smell as the motor brushes seat. This is
normal for universal motors and will last for about 5
minutes.
RODAGE DE LA POMPE I
1. Ouvrez le robinet de purge (B). Tourner le bouton vers la
droite.
2. Branchez le cordon d'alimentation.
3. Enfoncez la touche marche/arr6t a la position MARCHE
(l'ic6ne marche/arr6t apparaftra dans le coin superieur
gauche de I'affichage) (voir C).
Le compresseur demarre. Laissez tourner pendant 15
minutes pour roder les pieces internes.
REMARQUE : Si apres 15 minutes I'appareil ne fonctionne
pas correctement, ARRETEZ-LE
IMMEDIATEMENT et contactez le service
apres-vente.
4. Apres 15 minutes, enfoncez la touche marche/arr6t a la
position ARRET (l'ic6ne marche/arr6t ne sera plus visible
dans le coin superieur gauche de I'affichage).
5. Fermez le robinet de purge (D).
6. Enfoncez la touche marche/arr6t a la position marche.
Toumer vers la droite. Le compresseur demarre et remplit
le reservoir jusqu'a la pression de fermeture, puis s'arr6te.
REMARQUE:
REMARQUE:
1.
2.
3.
Une lois que suffisamment d'air comprime
est utilise, le manostat relance
automatiquement le moteur
Pendant le cycle rodage initial, il y aura une
16gere odeur electrique comme le moteur
balaye le siege. C'est normal pour les
moteurs universels et la volonte durent
pendant environ 5 minutes.
MARCHA INICIAL DE LA BOMBA I
Abra la Ilave de descompresion (vea B). H&galo girar hacia
la izquierda.
Enchufe el cordon electrico.
Presione el bot6n de encendido/apagado (on/off) para
dejarlo en la posici6n de encendido (ON) (el icono de
encendido/apagado aparecer& en la esquina superior
izquierda de la pantalla) (ver C). El compresor arrancar&
200-2449
OUVERT D
ABIERTO CLOSE
", FERMI_
" SE CIERRAN'x "/
", I/
Permita el funcionamiento del compresor durante 15
minutos, a fin de suavizar los componentes internos.
NOTA: Si despues de 15 minutos la unidad no opera
correctamente, AP/kGUELA INMEDIATAMENTE y
pongase en contacto con el Centro de Servicio.
4. Despues de 15 minutos, presione el bot6n de
encendido/apagado (on/off) para dejarlo en la posici6n de
apagado (OFF) (el icono de encendidotapagado ya no
estar& visible en la esquina superior izquierda de la
pantalla).
5. Cierre la Ilave de descompresion. (vea D).
6. Presione el boton de encendido/apagado (on/off) para
dejarlo en la posicion de encendido (ON). Hagalo girar
hacia la derecha. El compresor comenzar& a funcionar,
Ilenar& el tanque hasta la presion de desconexion y dejara
de funcionar.
NOTA: AI utilizar el aire comprimido, el interruptor de
presion arrancara automaticamente el motor.
NOTA: Durante el ciclo de adaptacion inicial, habr& un olor
electrico leve como el motor cepilla el asiento. Esto es
normal para los motores universales y la voluntad
dura pot cerca de 5 minutos.
13