ITEM # 7 80V EDGER MODEL #KE 2080-06 Español p. 20 ATTACH YOUR RECEIPT HERE Serial Number Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-888-3KOBALT (1-888-356-2258), 8 a.m. - 8 p.m., EST, Monday - Friday.
TABLE OF CONTENTS 2 Package Contents................................................................................................................. 3 Hardware Contents............................................................................................................... 4 Symbols................................................................................................................................. 5 Safety Information........................................................................
PACKAGE CONTENTS A D I 1 F I PART A B C D E F G H I DESCRIPTION Battery Release Button Trigger Lock-off Lever Safety lock-out switch Front/Auxiliary Handle Skid Plate Guard Blade Edger Wheel QUANTITY 1 1 1 1 1 1 1 1 1 PART J K L M N O 3 DESCRIPTION Tube Wing Nut Washer Axle sleeve Rubber washer Wheel axle QUANTITY 1 1 1 1 1 1
HARDWARE CONTENTS (not shown actual size) AA BB CC Fastening Knob Bolt Bracket Qty. 1 Qty. 1 Qty. 1 DD Wrench Qty. 1 EE Metal rod Qty.
SYMBOLS Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer. SYMBOLS DESIGNATION EXPLANATION V A Hz W min Volts Amperes Hertz Watts Minutes Direct Current Voltage Current Frequency (cycles per second) Power Time Type or a characteristic of current no No Load Speed Rational speed, at no load Per Minute Revolutions, strokes, surface speed, orbits, etc.
SYMBOLS Save these Instructions The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING an imminently hazardous situation, which, if not avoided, will DANGER Indicates result in death or serious injury. a potentially hazardous situation, which, if not avoided, could WARNING Indicates result in death or serious injury.
SAFETY INFORMATION WARNING Read and understand all instructions before using this product. Failure to follow all instructions listed . • liquids, gases, or dust. Power tools create sparks that may ignite the dust or fumes. • Do not allow children or untrained individuals to use this unit. • Don’t expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. • Do not handle battery or tool with wet hands. • Never allow children to operate the equipment.
SAFETY INFORMATION • Do not charge battery in the rain, or damp or wet locations. Following this rule will reduce the risk of electric shock. • For household use only. • Battery tools do not have to be plugged into an electrical outlet; therefore, they are always in operating condition. Be aware of possible hazards when not using your battery tool or when personal injury. • Remove or disconnect battery before servicing, cleaning or removing material from the gardening appliance.
SAFETY INFORMATION Dress Properly – Do not wear loose clothing or jewelry. They can be caught in moving parts. Use of rubber gloves and substantial footwear is recommended when working outdoors. Wear protective hair covering to contain long hair. Use the Correct Appliance – Do not use appliance for any job except that for which it is intended.
PREPARATION Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: ASSEMBLY INSTRUCTIONS WARNING • Replace the battery or charger immediately if the battery case or charger cord is damaged. • Always make sure the safety lock-out switch is OFF before inserting or removing the battery.
ASSEMBLY INSTRUCTIONS BATTERY IMPORTANT: The battery is not charged when it is purchased. Before using the edger for 2 Q A and charge. 2. To install: a. b. Align the battery with the cavity in the battery housing. Insert the battery into the handle until the battery release button (A) locks into place. Push down on the battery until it locks into place. You should hear a “click” once it is installed. Note: The battery can only be installed one way. 3. To remove: a.
OPERATING INSTRUCTIONS WARNING To avoid injury: • Do not squeeze the trigger while the • Do not carry the er is inverted. er with your finger on the switch. Avoid unintentional starting. 1. To turn on: a. Push the safety lock-out switch (D) forward to unlock. 3 Lock Unlock b. Press the lock-off lever (C). Squeeze the trigger (B) to start. To turn off: a. Release the trigger (B) . C b. Pull the safety lock-out switch (D) rearward to lock.
OPERATING INSTRUCTIONS 3. To replace the blade If the blade worn out, replace it with a new one (not provided) produced by Kobalt. a. Remove the battery pack. b. Use a metal rod (EE) to fix the blade. c. Remove the nut by turning it counterclockwise with the wrench (DD) provided. d. Remove the washer. DD Nut Washer e. Remove the old blade and replace it with a new one. f. Place the washer on the blade. g. Place the screw on the washer and tighten it counterclockwise with the wrench provided.
CARE AND MAINTENANCE 1. Replacing the skid plate 1 a. Remove the screws. b. Replace with the new skid plate. c. Tighten the screws. 2. Replacing the wheel 2a a. Remove the battery. O b. Remove the wing nut (K), washer (L), axle sleeve (M), wheel (I), axle sleeve (M), rubber washer (N) and wheel axle (O) orderly from the wheel assembly. I M M Slot N c. Replace with the new wheel. L d.
CARE AND MAINTENANCE Edger Guard and Motor Maintenance Note: Before performing maintenance, remove battery from the tool. a. Remove dirt and debris from guard using a paint brush (not included). b. Clean dirt and debris off of motor cover and connection joints. c. Clean the blade by using a wire brush and spraying with an appropriate degreaser.
TROUBLESHOOTING If you still have questions or an unresolved issue after going through this troubleshooting guide, or just want to speak to a Kobalt product expert, please call our customer service department at 1-888-3KOBALT (1-888-356-2258), 8 a.m. - 8 p.m., EST, Monday – Friday. PROBLEM Motor fails to start when switch trigger is depressed. POSSIBLE CAUSE 1. Battery is not secure. CORRECTIVE ACTION 1. To secure the battery, make sure the latches on the battery compartment snap into place. 2.
REPLACEMENT PARTS LIST For replacement parts, call our customer service department at 1-888-3KOBALT (1-888-356-2258), 8 a.m. - 8 p.m., EST, Monday - Friday.
