ITEM #2220273/2220274 80 V LITHIUM-ION CORDLESS POLE SAW MODEL #KPS 1081-06 Español p. 26 ATTACH YOUR RECEIPT HERE Serial Number Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-888-3KOBALT (1-888-356-2258), 8 a.m. - 8 p.m., EST, Monday - Sunday.
TABLE OF CONTENTS Product Specifications ���������������������������������������������������������������������������������������������������������� 3 Package Contents ���������������������������������������������������������������������������������������������������������������� 4 Symbols �������������������������������������������������������������������������������������������������������������������������������� 6 Safety Information ��������������������������������������������������������������������
PRODUCT SPECIFICATIONS SPECIFICATIONS Type Cordless, Battery-powered Battery 80 V Lithium-ion Bar length 10 in. (254 mm) Chain pitch 1/4 in. (6.3 mm) Chain type 25AP058X Guide bar type 100SDAA041 Weight (without battery) 9.8 lbs. (4.45 kg) The recommended ambient temperature range: Item Temperature Appliance storage temperature range -4°F (-20°C) - 158°F (70°C) Appliance operation temperature range 6.
PACKAGE CONTENTS E F H B A G C I J K D M P N N 4 L O
PACKAGE CONTENTS Q S R PART DESCRIPTION QUANTITY PART DESCRIPTION QUANTITY A Lower Tube 1 M Chain Tension Screw 1 B Handle Pole 1 N Bar Cover 1 C Extension pole 1 O Bar 1 D Power head pole 1 P Saw Chain 1 E Battery Release Button 1 Q Wrench 1 F Rear Handle 1 R Strap 1 G Lock-off Lever 1 S Scabbard 1 H Trigger Switch 1 I Collar 1 J Upper Tube 1 K Oil Cap 1 L Bar Cover Knob 1 5
SYMBOLS Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer. SYMBOL DESIGNATION EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power no No Load Speed Rational speed, at no load Per Minute Revolutions, strokes, surface speed, orbits etc.
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
SAFETY INFORMATION Read All Instructions WARNING Do not operate near electrical power lines. The unit has not been designed to provide protection from electric shock in the event of contact with overhead electric lines. Consult local regulations for safe distances from overhead electric power lines and ensure that the operating position is safe and secure before operating the saw chain pole pruner. WARNING Read all safety warnings and all instructions.
SAFETY INFORMATION • Use only Kobalt charger (KRC 80-06, KRC 30-06). POLE SAW SAFETY WARNINGS • Keep all parts of the body away from the saw chain. Do not remove cut material or hold material to be cut when blades are moving. Make sure the switch is off when clearing jammed material. Saw chain continues to move after the switch is turned off. A moment of inattention while operating the extended-reach pruner may result in serious personal injury. • Carry the pole saw by the handle with the saw chain stopped.
SAFETY INFORMATION • Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained. • Do not modify or attempt to repair the appliance or the battery pack (as applicable) except as indicated in the instructions for use and care.
PREPARATION Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list. If any part is missing or damaged, do not attempt to assemble the product. Helpful Tools: Wrench for tightening the chain and connecting the poles. UNPACKING • This product has been shipped unassembled. • Carefully remove the product and any accessories from the box. Make sure that all items listed in the Package Contents list are included.
ASSEMBLY INSTRUCTIONS 1. Connecting the poles a. Insert the extension pole (C) into the handle pole (B) and slide together. b. Lower the collar (I) on the extension pole (C) to the threaded base on the handle pole (B) and rotate clockwise to secure. c. Repeat this process to attach the extension pole (C) to the power head pole (D). 1 B C I WARNING Periodically check the connections to ensure that they are tightened securely. D 2.
ASSEMBLY INSTRUCTIONS 3a. To install the battery: a. Align the battery (not included) with the battery compartment. b. Insert battery into the battery compartment until battery release button (E) locks into place. You should hear a “click” once it is installed. 3 E 3b. To remove the battery: a. Press the battery release button (E) on the battery compartment. This will cause the battery to raise out of the tool slightly. b. tool.
OPERATING INSTRUCTIONS To turn on and off • Slide the lock-off lever (G). Squeeze the trigger switch (H) to start. • Release the trigger switch (H) to stop. Note: The lock-off lever must be engaged before the trigger is active. Once the trigger is engaged, release the lock-off lever. H G Preparation for cutting • Wear non-slip gloves for maximum grip and protection. • Maintain a proper grip on the unit whenever the motor is running.
OPERATING INSTRUCTIONS • Release the trigger as soon as the cut is completed. Failure to follow proper cutting procedures will result in the bar and chain binding and becoming pinched or trapped in the limb. If this should happen: • Stop the motor and remove the battery from the pole saw. • If the limb can be reached from the ground, lift the limb while holding the saw. This should release the “pinch” and free the saw. • If the saw is still trapped, call a professional for assistance.
15 • Keep the tree between you and the chain while limbing. Cut from the side of the tree opposite of the branch you are cutting. • Do not cut from a ladder; this is extremely dangerous. Leave this operation for professionals. • Do not make the flush cut next to the main limb or trunk until you have cut off the limb further out to reduce the weight. F ollowing proper cutting procedures will prevent stripping the bark from the main member. • Do not use the pole saw for felling or bucking.
CARE AND MAINTENANCE Chain & Bar Assembly During use, the chain will stretch and become dull. Debris and saw dust can also collect underneath the bar cover. Use the following steps to maintain your pole saw and chain. • Release chain tension by turning the chain tension screw (M), located behind the bar and chain, counterclockwise with the wrench (Q). Q M • Unscrew the bar cover knob (L). L • Remove the cover.
CARE AND MAINTENANCE • To replace the bar and chain, loop the chain over the sprocket and place the bar against the bar stud slot. Bar Stud Slot Sprocket • Ensure that the chain tensioning pin is located in the tensioning hole on the chain bar. • Also ensure that the rubber block and chain bar are free of oil, as this helps to keep tension on the chain. Chain Tensioning Pin • Replace the side cover and bar cover knob (L), but do not fully tighten.
CARE AND MAINTENANCE • Using the wrench (Q) on the chain tension screw (M), turn clockwise. Q M • Turn clockwise until there is enough play that the chain can be pulled away from the bar, but not so much that the runners can be pulled out of the bar. • Once you have the correct tension, fully tighten the locking knob. N ote: Chains stretch with use. Check tension often. Never tension a warm chain before storing, as chains shrink when cool. This can damage chain, bar and saw.
CARE AND MAINTENANCE Chain tension • Stop the motor and remove the battery before setting the chain tension. Turn the bar cover knob counterclockwise to loosen the bar cover but do not remove the bar cover. Turn the chain tensioning screw clockwise to tension chain. Turn the guide bar knob clockwise to tighten. Refer to the Replacing the bar and chain section for additional information.
CARE AND MAINTENANCE Chain Oiler WARNING To avoid possible serious injury, stop the motor and remove the battery from the pole saw before replacing the bar, chain or performing any maintenance operation. • Use Premium Bar and Chain Lubricant. It is designed for chains and chain oilers and is formulated to perform over a wide temperature range with no dilution required. • Remove the cap (K) and carefully pour into the bar lube reservoir. • Replace the cap and tighten securely.
CARE AND MAINTENANCE Chain maintenance For smooth and fast cutting, the chain needs to be maintained properly. The following conditions indicate that the chain requires sharpening: • Wood chips are small and powdery. Raker (Depth Gauge) Clearance • Chain must be forced through the wood during cutting. • Chain cuts to one side. During maintenance of the chain, consider the following: • Improper filing angle of the side plate can increase the 1/32” (0.79mm) risk of severe kickback.
CARE AND MAINTENANCE • Using light but firm pressure, stroke towards the front corner of the tooth. Lift file away from the steel on each return stroke. • Put a few firm strokes on every tooth. File all left hand cutters in one direction. Then move to the other side and file the right hand cutters in the opposite direction. • Remove filings from the file with a wire brush. CAUTION Dull or improperly sharpened chain can cause excessive motor speed during cutting which may result in severe motor damage.
TROUBLESHOOTING If you still have questions or an unresolved issue after going through this troubleshooting guide, or just want to speak to a Kobalt product expert, please call our customer service department at 1-888-3KOBALT (1-888-356-2258), 8 a.m. - 8 p.m., EST, Monday – Sunday. PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Bar and chain running hot and smoking. 1. Check chain tension for overtightened condition. 1. Tension chain. Refer to Chain Tension earlier in this manual. 2.
REPLACEMENT PARTS LIST For replacement parts, call our customer service department at 1-888-3KOBALT (1-888-356-2258), 8 a.m. - 8 p.m., EST, Monday - Sunday.