Use and Care Guide

General Purpose Filter
Acetaldehyde
Acetic acid (concentrated)
Acetone
Acrylonitrile
Ammonia
Ammonium flouride
Ammonium hydroxide
Ammonium sulfide
Anaerobic adhesives & sealants
Antifreeze
Benzene
Benzoic acid
Benzyl alcohol
Brake fluids
Bromobenzene
Butyric acid
Carbolic acid
Carbon disulfide
Carbon tetrachloride
Caustic potash solution
Caustic soda solution
Chlorobenzene
Chloroform
Cresol
Cyclohexanol
Cylohexanone
Cyclohexene
Dimethyl formamide
Dioxane
Ethane tetrachloride
Ethyl acetate
Ethyl ether
Ethylamine
Ethylene chlorohydrin
Ethylene dichloride
Ethylene glycol
Formic acid (concentrated)
Freon (refrig. & propell.)
Gasoline (high aromatic)
Hydrazine
Hydrochloric acid (concentrated)
Lacquer thinner
Methyl alcohol
Methylene chloride
Methylene salicylate
Mike of lime (CaOH)
Nitric acid (concentrated)
Nitrobenzene
Nitrocellulose lacquer
Phenol
Phosphorous hydroxy chloride
Phosphorous trichloride
Phopionic acid
Pyridine
Sodium hydroxide
Sodium sulfide
Styrene
Sulfuric acid (concentrated)
Sulphural chloride
Tetrahydronaphthalene
Tiophene
Toluene
Turpentine
Xylene
Perchlorethylene and others
Tlas “Perma-Guard”
Buna N
Cellulube #150 and #220
Crylex # cement
* Eastman 910
Garlock #98403 (polyurethane)
Haskel #568-023
Hilgard Co.’s hil phene
Houghton & Co. oil #1120,#1130 and 1055
Houtosafe 1000
Kano Kroil
Keystone penetrating oil #2
*Loctite 271
*Loctite 290
*Loctite 601
*Loctite Teflon-Sealant
Marvel Mystery Oil
Minn Rubber 366Y
National Compound #N11
“Nylock” VC-3
Parco #1306 Neoprene
*Permabond 910
Petron Pd287
Prestone
Pydraul AC
Sears Regular Motor Oil
Sinclair oil “Lily White”
Stauffer Chemical FYRQUEL #150
Stillman #SR 269-75 (polyurethane)
Stillman #SR 513-70 (neoprene)
Tannergas
Telar
Tenneco andrerol #495 & #500 oils
Titon
*Vibra-tite
Zerex
*When in raw liquid form.
Before pressurizing the system, always ensure that the top is securely locked to the bottom piece by turning
the filter body clockwise. Always release the pressure in the unit before removing the bowl, or injury may
result.
If you have trouble removing the filter body there may still be pressure.
Discard seals and polycarbonate clear bowls if they are damaged or broken.
Replace and clean the filter when no longer functioning fully.
Clean the filter by removing it and using an air gun to blow out captured particles.
After each use drain the polycarbonate clear bowls. Make sure to cover the bottom of the filter with a dry
cloth and push in the manual drain to reduce splatter.
Make sure to follow previous installation instructions when reinstalling unit.
Maintenance
WARNING
MATERIALS THAT ATTACK POLYCARBONATE PLASTIC (PARTIAL LISTING)
TRADE NAMES OF ATTACKING MATERIALS
3. Make sure the arrow points to the outlet. See Figure 2.
4. Install the unit with the appropriate pipe size without using fittings and couplings that
restrict the airflow.
5. Always use PTFE tape on all of the threads.
6. Connect the air supply to the inlet port.
PRINTED IN CHINA