KOBE Brand Range Hood Model No.
- READ AND SAVE THESE INSTRUCTIONS - CONTENTS Important Safety Instructions................................................................................................. 1 Components Of Package...................................................................................................... 3 Installation............................................................................................................................. 4 Operating Instructions...............................................
IMPORTANT SAFETY INSTRUCTIONS - PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION - WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, OBSERVE THE FOLLOWING: 1) Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards, including fire-rated construction. 2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden utilities.
What to Do In The Event Of a Range Top Grease Fire SMOTHER FLAMES with a close fitting lid, cookie sheet, or metal tray, and then turn off the burner. KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911. NEVER PICK UP A BURNING PAN – You May Get Burned. DO NOT USE WATER, including wet dishcloths or towels – a violent steam blast will result.
COMPONENTS OF PACKAGE ( M u s t k e e p a ll m a te ria l fo r re tu rn s o r re fu n d s ) RANGE HOOD BOX KOBE Range Hood – 1 Warranty Registration Card – 1 Instructions Manual – 1 Baffle Filter - 2 (for 30”, 36”, 42” hood) - 3 (for 48” hood) Bottom Casing - 1 (for 30” hood) - 3 (for 36” & 42” hood) - 2 (for 48” hood) 7” Round Adapter - 1 ORIGINAL KIT (Sold Separately) Option of: Model No.
INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation Calculate the length of the installation, before installing the hood. (All calculation is measure in inches.
SA F E T Y W A R N IN G HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF IT IS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING, CLEANING OR SERVICING. NOTE: BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER, DAMAGE TO THE HOOD MAY OCCUR. Installation Contents Under the Cabinet................................................................................................................. 6 Stand Alone .................................................................................................
UNDER THE CABINET INSTALLATION Figure 1 Preparation before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. Decide the location of the venting pipe from the hood to the outside. Refer to Figure 1. A straight, short venting run will allow the hood to perform more efficiently. Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood.
Figure 5 Ductwork Installation 6. 7. 8. Use aluminum or steel pipe to connect the plastic exhaust on the hood to the ductwork above. Use duct tape to make all joints secure and air tight as shown on Figure 4. To convert ductwork to 7” round, attached 7” round adapter (provided) to the 6” round plastic exhaust. For 48” hood, prepare either separate parallel connection or upside down Yconnection for proper ductwork installation. Refer to Figure 5.
STAND ALONE INSTALLATION ***This installation only applied with the purchase of an optional duct cover: Figure 8 Preparation before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. Decide the location of the venting pipe from the hood to the outside. Refer to Figure 8. A straight, short venting run will allow the hood to perform more efficiently. Try to avoid as many transitions, elbows, and long run as possible.
2. 3. Align hood-mounting bracket to the two screws on the wall and hook hood into place. Tighten screws to secure hood to the wall. For safety purposes, extra knockout holes on the back of the hood are provided. Knockout the holes. Remove the baffle filters and attach screws to the wall by accessing underneath the hood. CAUTION: MAKE SURE HOOD IS SUCURE BEFORE RELEASING Figure 12 Wiring to Power Supply Figure 13 SA F E T Y W A R N IN G RISK OF ELECTRICAL SHOCK.
8. Slide the duct cover onto the hood. Attach screws from underneath the hood to the duct cover. Figure 15 Install Accessories 9. 10. Refer to Figure 15 Slide the baffle filter into the hood. Push the baffle filter upward. Slide forward. Pull downward. Fit into place. For bottom casing, repeat above steps. Refer to page 15. Final Assembly 11. 12. Turn power ON in control panel. Check all lights and fan operation. Make sure to leave this manual for the homeowner.
OPERATION INSTRUCTIONS This KOBE hood is equipped with four electronic controls with a 10-second standby startup & 30second delay shutoff, powerful centrifugal squirrel cage with baffle filters, and bright 12-volt 20-watt halogen lights. The four electronic controls are Light Control, Speed Control A, Speed Control B and the Power Control (On/Off). Refer to Figure 16. Figure 16 Light Control Power Control Speed Control B Speed Control A TURN ON: Press Power Control (On/Off) button once.
MAINTENANCE For the optimal level of operation, clean the range hood surface and baffles regularly. To Clean Hood Surface CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. *** Regular care will help preserve its fine appearance. 1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth. 2. If hood looks splotchy (stainless steel hood), use an orange base cleaner to clean the surface of the hood. Avoid cleaner to get on the control switches.
SPECIFICATIONS MODEL / SIZE CH0030SQB / 30” CH0036SQB / 36" CH0042SQB / 42” CH0048SQB / 48” COLOR # 304 Commercial Grade Stainless Steel VOLTAGE NUMBER OF MOTORS 120V 60Hz 1 – 30”, 36”, 42” 2 – 48” DESIGN 18-Gauge Seamless / Satin Finish FAN TYPE: CENTRIFUGAL Squirrel Cage EXHAUST Top 6” Round x 1 – 30”, 36”, 42” Top 6” Round x 2 – 48” 7” Round Adapter CONTROLS Electronic Control (4 Buttons) – 10-Second Standby Startup 30-Second Delay Shutoff HALOGEN LIGHTS 12V 20W x 2 – 30”, 36” 12V 20W x 3
MEASUREMENTS & DIAGRAMS All measurements in ( ) are millimeters. All inch measurements are converted from millimeters. Inch measurements are estimated. - FOR UNDER THE CABINET MODEL NO.: CH0030SQB CH0036SQB CH0042SQB MODEL NO.: CH0048SQB - FOR STAND ALONE (WITH OPTIONAL DUCT COVER) MODEL NO.: CH0030SQB CH0036SQB CH0042SQB MODEL NO.
***Rear Knockout Holes ***Hood-Mounting Bracket 15
PARTS LIST MODEL NO.: CH0030SQB CH0036SQB CH0042SQB CH0048SQB NO. 1 2 3 DESCRIPTION 7” Round Adapter 6” Round Plastic Exhaust Hood Casing 4 5 6 7 8 9 10 11 Control Unit Control Board Halogen Light Unit (12V 20W Max.
(Optional Duct Cover) ORIGINAL KIT NO. DESCRIPTION 01 Hood-Mounting Bracket 02 Screw (3/16” x 3/8”) 03 Duct Cover 02 MODEL /SIZE CH0030DC-12 CH0036DC-12 CH0042DC-12 CH0048DC-12 Screw (3/16” x 3/8”) RECIRCULATING KIT NO.
MODEL NO.
MODEL NO.
MODEL NO.
CIRCUIT DIAGRAM MODEL NO.
MODEL NO.
DISCLAIMER 1. CAREFULLY INSPECT ALL ITEMS FOR DAMAGES BEFORE ACCEPTING DELIVERY. NOTE ANY DAMAGES ON THE FREIGHT BILL OR EXPRESS RECEIPT. REQUEST NAME AND SIGNATURE OF THE CARRIER’S AGENT AND KEEP COPY TO SUPPORT YOUR CLAIM. Upon acceptance of items, owner assumes responsibility for its safe arrival. Damages should be reported to carrier and a claim filed. Failure to do this could result in the carrier refusing to honor your claim. The carrier will furnish you with necessary forms for filing a claim.
WARRANTY WARRANTY CERTIFICATE KOBE Range Hoods, Inc. warrants all products manufactured or supplied by it to be free from defects in workmanship and materials. Its obligations pursuant to this warranty are limited to a period of two years from the date of purchase and to the repair or replacement at its option and subject to the terms and conditions stated below, of any component part, which its examination shall disclose to be so defective.
CONSEQUENTIAL DAMAGE The warrantor is not responsible for any consequential damage. SOME STATES DO NOT ALLOW THE EXCLUSION OF CONSEQUENTIAL DAMAGE SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU. IMPLIED WARRANTIES/STATE LAW Any implied warranties, including the implied warranty of merchantability and fitness for purpose, imposed on the sale by the laws of the state of sale are limited to two year from the date of original purchase. Some states do not allow limitations on the duration of implied warranties.
PRODUCT REGISTRATION Register Your Product! Any covered failure occurring within two years of original purchase arising from defective workmanship or material in manufacture will be repaired or at our option the unit will be replaced free of charge by an authorized KOBE Range Hoods Agent or KOBE Range Hoods as applicable. Keep proof of purchase (original invoice) handy for inspection.
