KOBE Brand Range Hood Model No.
{THIS PAGE LEFT PURPOSELY BLANK}
- READ AND SAVE THESE INSTRUCTIONS - CONTENTS IMPORTANT SAFETY INSTRUCTIONS.................................................................................... 1 COMPONENTS OF PACKAGE ................................................................................................. 3 INSTALLATION ......................................................................................................................... 4 UNDER THE CABINET INSTALLATION ...........................................................
IMPORTANT SAFETY INSTRUCTIONS - PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION - WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, OBSERVE THE FOLLOWING: 1) Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards, including fire-rated construction. 2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden utilities.
What to Do In The Event Of a Range Top Grease Fire • • • • SMOTHER FLAMES with a close fitting lid, cookie sheet, or metal tray, and then turn off the burner. KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911. NEVER PICK UP A BURNING PAN – You May Get Burned. DO NOT USE WATER, including wet dishcloths or towels – a violent steam blast will result.
COMPONENTS OF PACKAGE (Must keep all material for returns or refunds) RANGE HOOD BOX KOBE Range Hood – 1 W arranty Registration Card Instructions Manual – 1 Baffle Filter –1 - 2 (30”, 36”, 42”) - 3 (48”) Stainless Steel Spacer - 2 (30”) - 2 (36”) - 3 (42”) - 2 (48”) Oil Tunnel – 1 Ducting Transition – 1 Screw Package for Transition – 1 Hood-Mounting Bracket-2 Screw Package for Hood-Mounting Bracket w/ Rubber Stand –1 DUCT COVER KIT (Sold Separately) Option Of: Model No.
INSTALLATION PLEASE READ ENTIRE INSTRUCTION BEFORE PROCEEDING Calculation before Installation To calculate installation, please refer to Table 1. (All calculation in inches.
SAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF REMOVING ANY PARTS FOR INSTALLING, CLEANING OR SERVICING. NOTE: USING ELECTRICAL SCREWDRIVERS MAY CAUSE DAMAGE TO THE HOOD. Installation Table of Contents UNDER THE CABINET INSTALLATION................................................................................6 Preparation Before Installation ................................................................................................6 Hood Installation ................
UNDER THE CABINET INSTALLATION Preparation Before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. • • • • • • • • Decide the location of the venting pipe from the hood to the outside. Refer to Figure 1. A straight, short vent run will allow the hood to perform more efficiently. Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood.
Ductwork Installation 8. Use 8” round steel pipe (follow building codes in your area) to connect the ducting transition on the hood to the ductwork above. Use duct tape to make all joints secure and air tight. Refer to Figure 5. Wiring to Power Supply S AF E T Y W AR N I N G RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE BY QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES.
14. Turn power ON in control panel. Check all lights and fan operation. 15.
WALL MOUNT INSTALLATION ***Follow these installations only if installing with an optional duct cover: Preparation Before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. • • • • • • Decide the location of the venting pipe from the hood to the outside. Refer to Figure 9. A straight, short vent run will allow the hood to perform more efficiently. Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood.
2. 3. mark the leveling point of the hood. Position two mounting screws (not included) on the wall, leaving 1/8” away from the wall. Refer to Figure 13 Align hood-mounting bracket to the two screws on the wall and hook hood into place. Tighten screws to secure hood to the wall. For safety purpose, pre-drilled mounting holes are provided through the back of the hood. For a more secure installation, use as many mounting holes as needed to secure from the inside of hood (screws not included).
Duct Cover Installation 5. 6. Use 8” round steel pipe (follow building codes in your area) to connect the ducting transition on the hood to the ductwork above. Use duct tape to make all joints secure and air tight. Refer Figure 15. Slide the duct cover onto the hood. Use 3/16” x 3/8” screws (included) to attach duct cover to hood. Figure 15 Final Assembly CAUTION: Install heating lamps last. 7. 8. 9. 10. 11. 12. Drop oil tunnel into recess support near rear of hood. Refer to Figure 16.
OPERATING INSTRUCTIONS This KOBE hood is equipped with four electronic controls with a 10-second standby startup & 30second delay shutoff, powerful centrifugal squirrel cage with baffle filters, bright 12-volt 20-watt halogen lights, and heating lamp sockets (lamps not included). The four electronic controls are Light Control, Speed Control A, Speed Control B and the Power Control (On/Off). Refer to Figure 18.
MAINTENANCE SAFETY WARNING NEVER PUT YOUR HAND INTO AREA HOUSING THE FAN WHILE THE FAN IS OPERATING. For optimal operation, clean range hood and all baffle/spacer/filter/oil tunnel/oil container regularly. To Clean Hood Surface CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. *** Regular care will help preserve the appearance of the hood. 1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth. 2.
To Replace Light Bulb CAUTION: HALOGEN LIGHT UNIT MAY BE HOT! WAIT UNTIL UNIT IS COOL. 1. Make sure all controls are off, and range hood is unplugged. 2. Place a flat-head screwdriver between light cover and housing to remove cover . 3. Gently pull defective bulb straight out and discard. Light bulbs should be 12V 20W maximum. 4. Wear a cotton glove or use a cloth to handle the replacement bulb (do not handle with bare fingers as this may shorten the life of the bulb).
SPECIFICATIONS MODEL / SIZE COLOR CONSUMPTION / AMPERE VOLTAGE NUMBER OF MOTORS DESIGN FAN TYPE: CENTRIFUGAL EXHAUST CONTROLS HALOGEN LIGHTS HEATING LAMP SOCKET HOOD DIMENSION (W X D X H) OPTIONAL ACCESSORIES (Not Included) (W X D X H) HOOD WEIGHT (lbs) Blower Air Capacity (cfm)* Sone** CH0030SQB / 30“ CH0036SQB / 36“ CH0042SQB / 42“ CH0048SQB / 48“ #304 Commercial Grade Stainless Steel 900W / 8A 120V 60Hz 1 18 Gauge Seamless / Satin Finish Squirrel Cage Top Transition Rectangular to 8” Round x 1 Elec
MEASUREMENTS & DIAGRAMS All ( ) are in millimeter. All inch measurements are converted from millimeters. Inch measurements are estimated.
- FOR UNDER T HE CABINET – (Cont.
- FOR WALL MOUNT (WITH OPTIONAL DUCT COVER) – MODEL NO: CH0030SQB CH0036SQB CH0042SQB CH0048SQB 18
Rear Knockout Holes 19
- FOR WALL MOUNT (WITH OPTIONAL DUCT COVER) – (Cont.
4" (102) 1/3" (8.5) 1/2" (13) 1" (25.4) 1 - 3/8" (35) 1/4" (6.5) 3/16" (5) 11/16" (17.5) Hood-Mounting Bracket 6" (152) 7 - 1/2" (190.
PARTS LIST MODEL NO: CH0030SQB CH0036SQB CH0042SQB CH0048SQB BODY COMPONENTS NO.
3 2 1 4 5 23 22 6 7 9 21 8 18 20 3 16 19 10 11 15 17A 14 17B 17C 17D 12 13 Optional Duct Cover (Sold Separately) 24 3 23 17
Blower Assembly NO. 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 DESCRIPTION Screws (3/16” x 3/8”) Air Flow Grill Left Locknut Left Squirrel Cage Motor Right Squirrel Cage Right Locknut Air Chamber MODEL / SIZE 24 PART NO. CH100-4.1 CH100-4.2 CH100-4.3 CH100-4.4 CH100-4.5 CH100-4.6 CH100-4.7 CH100-4.
Electrical Assembly NO. 21.1 21.2 21.3 21.4 21.5 21.6 21.7 21.8 21.9 DESCRIPTION Capacitor Electrical Box Screws (3/16” x 3/8”) Processor Board Electrical Box Cover Setup Board Screws (3/16” x 3/8”) Transformer Screws (3/16” x 3/8”) MODEL / SIZE PART NO. CH100-21.1 CH100-21.2 CH100-21.3 CH100-21.4 CH100-21.5 CH100-21.6 CH100-21.7 CH100-21.8 CH100-21.9 21.2 21.9 21.3 21.4 21.1 21.5 21.8 21.6 21.
CIRCUIT DIAGRAM MODEL NO.
MODEL NO.
DISCLAIMER 1. CAREFULLY INSPECT ALL ITEMS FOR DAMAGES BEFORE ACCEPTING DELIVERY. NOTE ANY DAMAGES ON THE FREIGHT BILL OR EXPRESS RECEIPT. REQUEST NAME AND SIGNATURE OF THE CARRIER’S AGENT AND KEEP COPY TO SUPPORT YOUR CLAIM. Upon acceptance of items, owner assumes responsibility for its safe arrival. Report damages to the carrier and file a claim immediately. Failure to do so may result in the denial of your claim. The carrier will furnish you with necessary forms for filing a claim.
WARRANTY WARRANTY CERTIFICATE KOBE Range Hoods, Inc. warrants all products manufactured or supplied by it to be free from defects in workmanship and materials. Its obligations pursuant to this warranty are limited to a period of two years from the date of purchase and to the repair or replacement at its option and subject to the terms and conditions stated below, of any component part, which its examination shall disclose to be so defective.
3) The purchaser shall be responsible for any expenses involved in making the range hood readily accessible for servicing and where the range hood is installed outside the main sales territory of the retailer or service territory of the nearest approved KOBE Range Hoods Agent as applicable, for any traveling expenses and any costs of transporting the range hood or parts thereof to and from the dealer or Service Agent 4) The purchaser must produce proof of purchase together with this warranty certificate whe
PRODUCT REGISTRATION Register Your Product! Any covered failure occurring within two years of original purchase arising from defective workmanship or material in manufacture will be repaired or at our option the unit will be replaced free of charge by an authorized KOBE Range Hoods Agent or KOBE Range Hoods as applicable. Keep proof of purchase (original invoice) handy for inspection.
{THIS PAGE LEFT PURPOSELY BLANK}
KOBE Range Hoods 10505 Valley Blvd Suite # 302 El Monte, CA 91731 USA http://www.KOBERangeHoods.com This KOBE hood is manufactured for use in the USA and CANADA only. We do not recommend using this hood overseas as the power supply may not be compatible and may violate the electrical code of that country. Using a KOBE hood overseas is at your own risk and will void your warranty. VER.
