KOBE Range Hoods Brillia Series CHX91 SQB-2 Series Model No.
IMPORTANT READ THIS FIRST READ BEFORE INSTALLTAION 1. Carefully check all contents of package(s). 2. Thoroughly inspect the unit for any shipping damages, cosmetic damages or defects. 3. Have a certified contractor/electrician test the unit before installation. IF THERE IS ANY PROBLEMS: 1. DO NOT INSTALL THE UNIT AND KEEP ALL ORIGINAL PACKAGING MATERIALS. 2. Have your original invoice as proof of purchase and product serial number ready. 3.
[ENGLISH] - READ AND SAVE THESE INSTRUCTIONS - CONTENTS IMPORTANGE SAFETY INSTRUCTIONS ..................................................................... 1 COMPONENTS OF PACKAGE ...................................................................................... 3 INSTALLATION ............................................................................................................... 4 OPERATING INSTRUCTIONS .......................................................................................
IMPORTANGE SAFETY INSTRUCTIONS - PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION - WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, OBSERVE THE FOLLOWING: 1. Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards, including fire-rated construction. 2. When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden utilities. 3.
What to Do in the Event of a Range Top Grease Fire 1. SMOTHER FLAMES with a tight fitting lid, cookie sheet, or metal tray, and then turn off the burner. KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911. 2. NEVER PICK UP A BURNING PAN – You May Get Burned. 3. DO NOT USE WATER, including wet dishcloths or towels – a steam blast will result. 4. Use an extinguisher ONLY if: a.
COMPONENTS OF PACKAGE (Must keep all materials for returns or refunds) Duct Cover Box (For Wall Mount Application Models Only) Range Hood Box {A} {B} {C} {D} {E} {F} {G} {H} {I} {J} {K} KOBE Range Hood Warranty Registration Card Quick Reference Guide 6” Round Vent Exhaust (Pre-Installed) 3-1/4” x 10” Exhaust Top Vent Cover with Rectangular Opening Top Vent Cover (to block Round Exhaust) Oil Tunnel x 1 Baffle Filters x 2 Stainless Steel Spacers x 2 Screws {A} {B} {L} {M} {N} {O} {P} Adjust Duct Cover D
INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation To calculate installation, please refer to TABLE 1 and TABLE 2. (All calculation in inches).
UNDER CABINET INSTALLATION Before Installation 1. Read any provided document(s). 2. Test the range hood by temporarily connecting it to an outlet and turning ON the fan and lights. 3. If you run into any problems, contact KOBE Range Hoods. Venting Options and Requirements 4. The range hood has 3 exhaust options: Top 6” Round, Top 3-1/4” x 10” Rectangular, and Rear 3-1/4” x 10” Rectangular. The range hood is factory set for vertical or horizontal venting using round or rectangular vent adapter. 5.
Hood Installation 13. Remove any protective film off the hood, if any. 14. For installing under the cabinet with recessed bottom, attach 4-inch wide wood filler strips (not included) on each side (Figure 5). 15. Create access opening for electrical plug or wires and hood exhaust under the cabinet. 16. Align the hood in the center of the cabinet. As an optional step, you may position a flat-surfaced object below the hood as a support. Alternatively, another person can temporarily hold the hood. 17.
WALL MOUNT INSTALLATION Before Installation 1. Read any provided document(s). 2. Test the range hood by temporarily connecting it to an outlet and turning ON the fan and lights. 3. If you run into any problems, contact KOBE Range Hoods. *Note: 6” Round Vent Exhaust is preinstalled on the range hood. Figure 1 Venting Options and Requirements 4. The range hood has 3 exhaust options: Top 6” Round, Top 3-1/4” x 10” Rectangular, and Rear 3-1/4” x 10” Rectangular.
14. Using reference on TABLE 2 and measurements on page XX to mark the leveling point of the hood. Position three 4*35 screws on the wall, leaving 1/8” away from the wall as shown in Figure 6. 15. Align hood-mounting bracket to the three screws on the wall and hook hood into place. Tighten screws to secure hood to the wall. 16. There are 4 installing holes at the back of the hood. Attached the four 4*35 screws through the installing holes from the front to the back.
OPERATING INSTRUCTIONS 3-Speed Mechanical Push Button NOTE: For best results, turn fan on prior to any preparation or cooking and keep fans running while cooking. Adjust speed as needed.
MAINTENANCE For optimal performance, clean the range hood surface and filters regularly. To Clean Hood Surface CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. ***Regular care will help preserve its fine appearance. 1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth. 2. If hood looks smudged (stainless steel hood), use a stainless steel cleaner to clean the surface of the hood. Avoid getting cleaning solution onto or into the control panel.
SPECIFICATIONS MODEL / SIZE CHX9130SQB-1 (30”) CHX9136SQB-1 (36”) CHX9130SQB-2 (30”) CHX9136SQB-2 (36”) COLOR Commercial Grade Stainless Steel CONSUMPTION / AMPERE 106W / 1.
MEASUREMENTS & DIAGRAMS ***All inch measurements are converted from millimeters. Inch measurements are estimated. ***All measurements in ( ) are millimeters. MODEL NO.: - FOR UNDER THE CABINET CHX9130SQB-1 (30”) / CHX9136SQB-1 (36”) CHX9130SQB-2 (30”) / CHX9136SQB-2 (36”) MODEL NO.
***Hood-Mounting Bracket ***Duct Cover-Mounting Bracket ***Duct Cover Support 13
PARTS LIST MODEL NO.: NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 CHX9130SQB-1 (30”) / CHX9136SQB-1 (36”) CHX9130SQB-2 (30”) / CHX9136SQB-2 (36”) DESCRIPTION 6” Round Exhaust Plate 3-1/4” x 10” Rectangular Exhaust 3-1/4” x 10” Top Vent Cover Control Switch LED Light Capacitor (5uF) x 2 Metal Oil Tunnel Left Motor Right Motor Left Impeller Right Impeller Spacer (33mm x 365mm) Baffle Filter (322mm x 365mm) LED Light Driver Duct Cover (For Wall Mount Only) NO.
CIRCUIT DIAGRAM MODEL NO.
TROUBLE SHOOTING Issue After installation, both motors and lights are not working. Lights are working, but motor(s) is not. The range hood is vibrating. The motor is working, but the lights are not working. The range hood is not venting out correctly. Possible Cause The power is not on. The wire connection is not secure. The control panel is defective. The motor(s) is defective. The capacitor(s) is defective. The control panel is defective. The blower system is not secure.
WARRANTY WARRANTY CERTIFICATE In order to obtain warranty service, you must provide proof of original purchase from a KOBE authorized Dealer. Please keep a copy of your original invoice as proof of purchase. ONE-YEAR LIMITED LABOR WARRANTY ON KOBE BRILLIA SERIES: For one year from the date of your original invoice from KOBE authorized dealer, we will repair any parts or components free of charge that failed due to manufacturing defects.
THIS WARRANTY WILL BE VOIDED BY: 1. Improper installation and failure to follow installation instructions. 2. Any repair, alternation, modification not authorized by KOBE. 3. Duct alternation, modification, and connection. 4. Incorrect electric current, voltage, or wiring. 5. Improper usage of the product such as commercial, outdoor, or other usage other than residential indoor usage. 6. Purchasing this product from an unauthorized KOBE dealer. 7.
WARRANTY INFORMATION FORM Fills in the blanks and keep this paper with the original invoice in a safe place for future service purpose. 1. Date of purchase : _______________________________ 2. Model No. :_______________________________ 3. Serial No. :_______________________________ For warranty service or spare parts purchase in US, contact: KOBE Service Center Email (best): customer.service@koberangehoods.
KOBE Range Hoods 11775 Clark Street Arcadia, CA 91006 USA www.koberangehoods.com This KOBE hood is made for use in the USA and CANADA only. We do not recommend using this hood overseas as the power supply may not be compatible and may violate the electrical code of that country. Using a KOBE hood overseas is at your own risk and will void your warranty. Cette hotte KOBE est fabriquée pour usage aux États-Unis et au Canada seulement.
