KOBE Brand Range Hood Model No.
- READ AND SAVE THESE INSTRUCTIONS - CONTENTS Important Safety Instructions................................................................................................. 1 Components of Package ....................................................................................................... 3 Installation............................................................................................................................. 4 Operation Instructions ............................................
IMPORTANT SAFETY INSTRUCTIONS - PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION - WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, OBSERVE THE FOLLOWING: 1) Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards, including fire-rated construction. 2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden utilities.
What to Do In The Event Of a Range Top Grease Fire SMOTHER FLAMES with a close fitting lid, cookie sheet, or metal tray, and then turn off the burner. KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911. NEVER PICK UP A BURNING PAN – You May Get Burned. DO NOT USE WATER, including wet dishcloths or towels – a violent steam blast will result.
COMPONENTS OF PACKAGE (Must keep all material for returns or refunds) BOX 1 OF 2 MODEL NO. IS2436GSB MODEL NO. IS2442GSB Glass Canopy w/ LCD Screen – 1 Baffle Filter – 2 Warranty Registration Card – 1 Instructions Manual – 1 Telescopic Stack – 1 Blower Unit - 1 Inner Duct Cover – 1 Outer Duct Cover – 1 Mounting Template – 1 7” Round Damper – 1 Screws Package * Attached to Hood BOX 2 OF 2 MODEL NO.
INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation To calculate installation, please refer to TABLE 1. (All calculation in inches.
Figure 1 Preparation before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. Decide the location of the venting pipe from the hood to the outside. (Figure 1) A straight, short vent run will allow the hood to perform more efficiently. Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood. Temporarily wire the hood to test for proper operation before installing.
Telescopic Stack Installation Figure 4 6. Align the telescopic stack to the pre-drill holes on the ceiling and securely fasten to the joists and cross framing lumber with eight screws (not provided). Make sure screws are driven into center of joists and cross framing lumber for maximum support. 7. Adjust the blower unit to the telescopic stack using reference F calculated in TABLE 1 on page 4 and measurements on pages 14-15.
Duct Cover Installation Figure 7 11. Slide the inner duct cover up and secure to the telescopic stack with four (ST 3 x 15) screws (provided). Refer to Figure 7. 12. With assistance, slide the outer duct cover to the blower unit and ask assistant to hold steady until step 15 is completed. 13. Attach glass canopy with LCD screen underneath the blower unit. Make sure blower unit is inside the housing connector. Refer to the PARTS LIST on pages 16-17. 14.
OPERATION INSTRUCTIONS Figure 9 LCD DISPLAY: PRESS TO TURN ON/OFF THE LCD SCREEN (When power is turned on, LCD screen will light up & remain lit until turn off. When power is turned off, LCD screen will remain lit for several seconds before turning off.) GENERAL SETUP (During menu option, if a function is not chosen within 10 seconds, the icon will stop flashing & menu option will end. Setting Time 1. Press until time icon flashes. 2. Press or (Choose to select current time by hh:mm. for A.M.
Setting Background Color 1. Press until 2. Press or flashes. to select background color (purple, light blue, or green). Setting Sound 1. Press until flashes. 2. Press to select sound. OR Press (When to mute sound. appears, keypad sound is ON.) HOOD OPERATION Turning Fan ON/OFF 1. Press to turn fan ON. (Each press of will cycle the fan through QuietMode™, Low, Medium, and High.) The screen will indicate: = QuietMode™ Speed = Low Speed = Medium Speed = High Speed 2.
Turning ISC (Integrated Sensor Control) ON/OFF 1. Press to turn ISC ON. ( will indicate that the ISC system is ON. When gas, smoke, or higher than normal room temperature is detected, fan will automatically turn ON. Fan will turn to its highest speed and decrease speed until all gas and smoke are eliminated.) 2. Press to turn ISC OFF. Turning Lights ON (Light control is separate from ON/OFF control. Turning power off will not turn lights off.) 1. Press to turn halogen lights ON.
MAINTENANCE SAFETY WARNING NEVER PUT YOUR HAND INTO AREA HOUSING THE FAN WHILE THE FAN IS OPERATING. For the optimal level of operation, clean the range hood surface and baffles/filters/oil containers regularly. To Clean Hood Surface CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. *** Regular care will help preserve the appearance of the hood. 1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth. 2.
To Replace Light Bulb CAUTION: HALOGEN LIGHT UNIT MAY BE HOT! WAIT UNTIL UNIT IS COOL. 1. Make sure all controls are OFF, and range hood is unplugged. 2. Place the flat-head screwdriver into the groove between the halogen light glass covering and the housing . 3. Gently separate glass covering from the housing . 4. Gently pull out the defective light bulb and discard. Light bulbs should be 12V 20W maximum. 5.
SPECIFICATIONS BOX 1 OF 2 MODEL / SIZE IS2436GSB / 36" IS2442GSB / 42” BOX 2 OF 2 MODEL / SIZE IS124DC – Duct cover with blower unit COLOR 18-Gauge Commercial Grade Stainless Steel CONSUMPTION / AMPERE 240W / 2.0A VOLTAGE 120V 60Hz NUMBER OF MOTORS 1 DESIGN 18-Gauge Seamless / Satin Finish FAN TYPE Squirrel Cage EXHAUST Top 7” Round Damper CONTROLS Touch Screen Multi Function LCD HALOGEN LIGHTS 12V 20W x 2 OPTIONAL ACCESSORIES (SOLD SEPARTELY) Recirculating Kit – Item No.
MEASUREMENTS & DIAGRAMS All ( ) measurements are in millimeter. All inch measurements are converted from millimeter. Inch measurements are estimated.
PARTS LIST MODEL NO.: IS2436GSB IS2442GSB (Box 1 of 2) MODEL NO. IS2436GSB MODEL NO. IS2442GSB NO. DESCRIPTION 01 Glass Canopy 02 03 04 05 06 07 08 09 MODEL IS2436GSB IS2442GSB Housing Connector Sensor Control Light Support Panel (Top) Light Support Panel (Bottom) Halogen Light Hood Casing LCD Screen Baffle Filter BF-0124 PART NO. GC-0036-01 GC-0042-01 PH-0001-01 PH-0002-01 PH-0003-01 PH-0003-02 PH-0004-01 PH-0005-01 PH-0006-01 PH-0007-01 (Box 2 of 2) MODEL NO. IS124DC NO.
MODEL NO.: IS2436GSB IS2442GSB BOX 1 OF 2 - GLASS CANOPY WITH LCD SCREEN 1 2 3 4 5 6 7 9 8 RECIRCULATING KIT - ITEM NO.
CIRCUIT DIAGRAM MODEL NO.
DISCLAIMER 1. CAREFULLY INSPECT ALL ITEMS FOR DAMAGES BEFORE ACCEPTING DELIVERY. NOTE ANY DAMAGES ON THE FREIGHT BILL OR EXPRESS RECEIPT. REQUEST NAME AND SIGNATURE OF THE CARRIER’S AGENT AND KEEP COPY TO SUPPORT YOUR CLAIM. Upon acceptance of items, owner assumes responsibility for its safe arrival. Report damages to the carrier and file a claim immediately. Failure to do so may result in the denial of your claim. The carrier will furnish you with necessary forms for filing a claim.
WARRANTY WARRANTY CERTIFICATE KOBE Range Hoods, Inc. warrants all products manufactured or supplied by it to be free from defects in workmanship and materials. Its obligations pursuant to this warranty are limited to a period of two years from the date of purchase and to the repair or replacement at its option and subject to the terms and conditions stated below, of any component, which its examination shall disclose to be so defective.
CONSEQUENTIAL DAMAGE The warrantor is not responsible for any consequential damage. UNLESS YOU LEAVE IN A STATE THAT DO NOT ALLOW THE EXCLUSION OF CONSEQUENTIAL. IMPLIED WARRANTIES/STATE LAW Any implied warranties, including the implied warranty of merchantability and fitness for purpose, imposed on the sale by the laws of the state of sale are limited to two year from the date of original purchase. Some states do not allow limitations on the duration of implied warranties.
PRODUCT REGISTRATION Register Your Product! Any covered failure occurring within two years of original purchase arising from defective workmanship or material in manufacture will be repaired or at our option, replaced free of charge by an authorized KOBE Range Hoods Agent or KOBE Range Hoods as applicable. Keep proof of purchase (original invoice) handy for inspection.
KOBE Range Hoods 10505 Valley Blvd Suite # 302 El Monte, CA 91731 USA http://www.KOBERangeHoods.com This KOBE hood is made for use in the USA and CANADA only. We do not recommend using this hood overseas as the power supply may not be compatible and may violate the electrical code of that country. Using a KOBE hood overseas is at your own risk and will void your warranty. V.
