KOBE Brand Range Hood CH-100 Series (18” Height) Model No.: CH0030SQB-1 (30”) CH0036SQB-1 (36”) CH0042SQB-1 (42”) CH0048SQB-1 (48”) RA-02 Series (18” Height) Model No.
- READ AND SAVE THESE INSTRUCTIONS - CONTENTS IMPORTANT SAFETY INSTRUCTIONS .................................................................................... 1 COMPONENTS OF PACKAGE.................................................................................................. 3 INSTALLATION .......................................................................................................................... 5 OPERATION INSTRUCTIONS...............................................................
IMPORTANT SAFETY INSTRUCTIONS - PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION - WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, OBSERVE THE FOLLOWING: 1) Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards, including fire-rated construction. 2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden utilities.
What to Do In The Event Of a Range Top Grease Fire • • • • SMOTHER FLAMES with a tight fitting lid, cookie sheet, or metal tray, and then turn off the burner. KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911. NEVER PICK UP A BURNING PAN – You May Get Burned. DO NOT USE WATER, including wet dishcloths or towels – a violent steam blast will result.
COMPONENTS OF PACKAGE (Must keep all material for returns or refunds) CH-100 Series RANGE HOOD BOX {A} KOBE Range Hood – 1 {B} Warranty Registration Card –1 {C} Instructions Manual – 1 {D} Oil Tunnel – 1 {E} Baffle Filter - 2 (30” & 36”) - 3 (42” & 48”) {F} Spacer – 2 {G} 8” Round Exhaust Plate – 1 {H} (42” & 48” only) {H} {I} {J} Screws Package – 1 Hood-Mounting Bracket – 2 Screws Package – 1 {I} {J} {A} Duct Cover (Sold Separately) Option Of: Model No.
RA-02 Series RANGE HOOD BOX (BOX 1 OF 2) {A} KOBE Range Hood – 1 {B} Warranty Registration Card –1 {C} Instructions Manual – 1 {D} Oil Tunnel – 1 {E} Baffle Filter 2 (30” & 36”) 3 (42” & 48”) {F} Spacer – 2 {G} 8” Round Exhaust Plate – 1 {F} {G} {H} (42” & 48” only) {H} Screws Package – 1 {I} Hood-Mounting Bracket – 1 {J} Screws Package – 1 {A} {I} {B} {J} {C} BOX 2 OF 2 ITEM NO.: RA02DC {K} {D} Duct Cover {E} {K} - FOR MORE INFORMATION, PLEASE VISIT OUR W EBSITE www.KOBERangeHoods.
INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation Calculate the length of the installation, before installing the hood. (All calculation is measure in inches.
SAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF IT IS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING, CLEANING OR SERVICING. NOTE: BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER, DAMAGE TO THE HOOD MAY OCCUR. CH-100 SERIES – UNDER THE CABINET INSTALLATION ................................................................. 7 CH-100 SERIES – STAND ALONE INSTALLATION ............................................................................. 9 RA-02 SERIES - INSTALLATION ........
CH-100 SERIES – UNDER THE CABINET INSTALLATION Figure 1 Preparation before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. Decide the location of the venting pipe from the hood to the outside. Refer to Figure 1. A straight, short venting run will allow the hood to perform more efficiently. Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood.
Figure 5 Ductwork Installation 7. Use 6” round steel pipe for 30” and 36” models or 8” round steel pipe for 42” and 48” models (follow building codes in your area) to connect the exhaust on the hood to the ductwork above. Use duct tape to make all joints secure and air tight. Refer to Figure 5. Wiring to Power Supply SAFETY WARNING Figure 6 RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST BE PROPERLY GROUNDED.
CH-100 SERIES – STAND ALONE INSTALLATION ***This installation only applies with the purchase of an optional duct cover: Figure 9 Preparation before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. Decide the location of the venting pipe from the hood to the outside. Refer to Figure 9. A straight, short venting run will allow the hood to perform more efficiently. Try to avoid as many transitions, elbows, and long run as possible.
5. Align hood-mounting bracket to the two screws on the wall and hook hood into place. Tighten screws to secure hood to the wall. 6. For safety purpose, pre-drilled mounting holes are provided through the back of the hood. For a more secure installation, use as many mounting holes as needed to secure from the inside of hood (screws not included). CAUTION: MAKE SURE HOOD SECURE BEFORE RELEASING. Figure 13 WALL IS Wiring to Power Supply Figure 14 SAFETY WARNING RISK OF ELECTRICAL SHOCK.
Figure 15 Duct Cover Installation 8. Use 6” round steel pipe for 30” and 36” models or 8” round steel pipe for 42” and 48” models (follow building codes in your area) to connect the exhaust on the hood to the ductwork above. Use duct tape to make all joints secure and air tight. Refer Figure 15. Slide the duct cover onto the hood. 9. Use 3/16” x 3/8” screws (included) to attach duct cover to hood. Figure 16 Install Accessories 10. Attach oil tunnel. Refer to Figure 16. 11. Refer to Figure 17.
RA-02 SERIES - INSTALLATION Figure 19 Preparation before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. Decide the location of the venting pipe from the hood to the outside. (Figure 18) A straight, short venting run will allow the hood to perform more efficiently. Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood.
Figure 22 Hood Installation CAUTION: If required to move the cooking range to install the hood, turn off the power on an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. 1. Using references in Table 2 and measurements on Page 21, mark the leveling locations point for hood-mounting bracket on the wall. 2. Secure two mounting screws (not provided) to the wall, leaving an 1/8” space from the wall. (Figure 22) 3.
Figure 26 Duct Cover Installation 6. Use 6” round steel pipe for 30” and 36” models or 8” round steel pipe for 42” and 48” models (follow building codes in your area) to connect the exhaust on the hood to the ductwork above. Use duct tape to make all joints secure and air tight. Refer Figure 24. 7. Use four 4mm x 8mm screws (included) to attach duct cover to hood. Refer to Figure 25. Install Accessories 8. Attach oil tunnel. Refer to Figure 26. 9. Refer to Figure 27.
OPERATION INSTRUCTIONS This KOBE hood is equipped with two rotary controls with powerful centrifugal squirrel cage, baffle filters, and bright LED lights. The two rotary controls are Light Control & Speed Control. Refer to Figure 28. Figure 28 Note: For best results, turn hood to QuietMode™ prior to preparation or cooking to establish airflow in the kitchen. Adjust speed as needed.
MAINTENANCE For the optimal level of operation, clean the range hood surface and baffles regularly. To Clean Hood Surface CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. *** Regular care will help preserve its fine appearance. 1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth. 2. If hood looks splotchy (stainless steel hood), use an orange base cleaner to clean the surface of the hood. Avoid cleaner to get on the control switches.
SPECIFICATIONS CH-100 Series MODEL / SIZE CH0030SQB-1 / 30” / Single Blower CH0036SQB-1 / 36" / Single Blower CH0042SQB-1 / 42” / Dual Blowers CH0048SQB-1 / 48” / Dual Blowers COLOR Commercial Grade Stainless Steel CONSUMPTION / AMPERE CH0030SQB-1 – 700W CH0036SQB-1 – 700W CH0042SQB-1 – 700W CH0048SQB-1 – 700W VOLTAGE 120V 60Hz NUMBER OF BLOWER 1 – 30”, 36” 2 – 42”, 48” DESIGN 18-Gauge Seamless / Satin Finish FAN TYPE: CENTRIFUGAL Squirrel Cage EXHAUST Top 6” Round – 30”, 36” Top 8” Round – 4
RA-02 Series MODEL / SIZE RA0230SQB-1 / 30” / Single Blower RA0236SQB-1 / 36" / Single Blower RA0242SQB-1 / 42” / Dual Blowers RA0248SQB-1 / 48” / Dual Blowers COLOR Commercial Grade Stainless Steel CONSUMPTION / AMPERE RA0230SQB-1 – 350W RA0236SQB-1 – 350W RA0242SQB-1 – 350W RA0248SQB-1 – 350W VOLTAGE 120V 60Hz NUMBER OF BLOWER 1 – 30”, 36” 2 – 42”, 48” DESIGN 18-Gauge Seamless / Satin Finish FAN TYPE: CENTRIFUGAL Squirrel Cage EXHAUST Top 6” Round – 30”, 36” Top 8” Round – 42”, 48” CONTROL
MEASUREMENTS & DIAGRAMS All measurements in ( ) are millimeters. All inch measurements are converted from millimeters. Inch measurements are estimated. CH-100 Series MODEL NO.
- FOR STAND ALONE (WITH OPTIONAL DUCT COVER) CH-100 Series MODEL NO.
All measurements in ( ) are millimeters. All inch measurements are converted from millimeters. Inch measurements are estimated. RA-02 Series MODEL NO.
PARTS LIST CH-100 Series MODEL NO.: CH0030SQB-1 (30”) CH0036SQB-1 (36”) CH0042SQB-1 (42”) CH0048SQB-1 (48”) NO.
CH-100 Series MODEL NO.
CH-100 Series MODEL NO.
RA-02 Series MODEL NO.: NO.
RA-02 Series MODEL NO.
RA-02 Series MODEL NO.
CIRCUIT DIAGRAM CH-100 Series MODEL NO.: CH0030SQB-1 (30”) CH0036SQB-1 (36”) CH0042SQB-1 (42”) CH0048SQB-1 (48”) RA-02 Series MODEL NO.
TROUBLE SHOOTING Issue After Installation, both motors and lights are not working. Possible Cause The power is not on. The wire connection is not secure. The control panel is defective. Solution Make sure the circuit breaker and the unit’s power is ON. Use a voltage meter to check the power supply. Check and tighten wire connection. Replace the control panel. Lights are working, but motor(s) is not. The motor(s) is defective. The capacitor(s) is defective. The control panel is defective.
DISCLAIMER 1. CAREFULLY INSPECT ALL ITEMS FOR DAMAGES BEFORE ACCEPTING DELIVERY. NOTE ANY DAMAGES ON THE FREIGHT BILL OR EXPRESS RECEIPT. REQUEST NAME AND SIGNATURE OF THE CARRIER’S AGENT AND KEEP COPY TO SUPPORT YOUR CLAIM. Upon acceptance of items, owner assumes responsibility for its safe arrival. Report damages to the carrier and file a claim immediately. Failure to do so may result in the denial of your claim. The carrier will furnish you with necessary forms for filing a claim.
WARRANTY WARRANTY CERTIFICATE KOBE Range Hoods warrants all products manufactured or supplied by it to be free from defects in workmanship and materials. Its obligations pursuant to this warranty are limited to a period of two years from the date of purchase and to the repair or replacement at its option and subject to the terms and conditions stated below, of any component part, which its examination shall disclose to be so defective.
3) The purchaser shall be responsible for any expenses involved in making the range hood readily accessible for servicing and where the range hood is installed outside the main sales territory of the retailer or service territory of the nearest approved KOBE Range Hoods Agent as applicable, for any traveling expenses and any costs of transporting the range hood or parts thereof to and from the dealer or Service Agent 4) The purchaser must produce proof of purchase together with this warranty certificate whe
PRODUCT REGISTRATION Register Your Product! Any covered failure occurring within two years of original purchase arising from defective workmanship or material in manufacture will be repaired or at our option the unit will be replaced free of charge by an authorized KOBE Range Hoods Agent or KOBE Range Hoods as applicable. Keep proof of purchase (original invoice) handy for inspection.
KOBE Range Hoods 11775 Clark Street Arcadia, CA 91006 USA http://www.KOBERangeHoods.com This KOBE hood is made for use in the USA and CANADA only. We do not recommend using this hood overseas as the power supply may not be compatible and may violate the electrical code of that country. Using a KOBE hood overseas is at your own risk and will void your warranty. Information subject to change without notice. VER.
