KOBE Range Hoods Brillia Series Model No.
IMPORTANT READ THIS FIRST READ BEFORE INSTALLATION 1. Carefully check all contents of packages. 2. Thoroughly inspect the unit for any shipping damages, cosmetic damages or defects. 3. Have a certified contractor/electrician test the unit before installation. IF THERE IS ANY PROBLEM: 1. DO NOT INSTALL THE UNIT AND KEEP ALL ORIGINAL PACKAGING MATERIAL. 2. Have your original invoice as proof of purchase and product serial number ready. 3.
[ENGLISH] - READ AND SAVE THESE INSTRUCTIONS - CONTENTS IMPORTANT SAFETY INSTRUCTIONS .................................................................................... 1 COMPONENTS OF PACKAGE.................................................................................................. 3 INSTALLATION .......................................................................................................................... 4 OPERATING INSTRUCTIONS........................................................
IMPORTANT SAFETY INSTRUCTIONS - PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION - WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, OBSERVE THE FOLLOWING: 1) Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards, including fire-rated construction. 2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden utilities.
What to Do In The Event Of a Range Top Grease Fire • • • • SMOTHER FLAMES with a tight fitting lid, cookie sheet, or metal tray, and then turn off the burner. KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911. NEVER PICK UP A BURNING PAN – You May Get Burned. DO NOT USE WATER, including wet dishcloths or towels – a steam blast will result.
COMPONENTS OF PACKAGE (Must keep all material for returns or refunds) Range Hood Box Duct Cover Box (Included in Wall Mount Hood ONLY) CH1120DC-1 {A} KOBE Range Hood {B} Warranty Registration Card {C} Quick Reference Guide {D} 3-1/4” x 10” Exhaust {E} Top Vent Cover {F} 6” Round Plastic Collar {G} Oil Tunnel {H} Baffle Filters x 2 {I} Stainless Steel Spacer x 2 {J} Wire Cap x 3 {K} Screw Package (for Under Cabinet) {L} {M} {N} {O} {P} {Q} Adjustable Duct Cover Screws Package Duct Cover-Mounting Bracket
INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation To calculate installation, please refer to TABLE 1 and TABLE 2. (All calculation in inches.
SAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF REMOVING ANY PARTS FOR INSTALLING, CLEANING OR SERVICING. NOTE: BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER, DAMAGE TO THE HOOD MAY OCCUR.
UNDER CABINET INSTALLATION Figure 1 Preparation before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. - - Decide the location of the venting pipe from the hood to the outside. Refer to Figure 1. A straight, short vent run will allow the hood to perform more efficiently. Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood. Temporarily wire the hood to test for proper operation before installing.
- Align and secure Top Vent Cover {E} and 3-1/4” x Figure 5 10” Vent Cover (removed from rear exhaust) using 14 screws (13 screws taken from 6” exhaust. (Figure 5) - Attach the 3-1/4” x 10” Exhaust {D} to rear exhaust (located inside hood) using 10 screws taken from rear vent cover. (Figure 6) Hood Installation CAUTION: If moving the cooking range is necessary to install the hood, turn off the power in an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE.
Figure 7 Ductwork Installation 10. Use steel pipe to connect the exhaust on the hood to the ductwork. Use duct tape to make all joints secure and air tight. Install Accessories 11. Install the Oil Tunnel {G} into recess support near rear of hood. Refer to Figure 7. 12. Install Baffle Filters {H} and Stainless Steel Spacers {I}. Angle baffle filter toward back of hood. Push the baffle filter up until almost level. Slide forward into recess behind the front of hood. Lower baffle filter.
WALL MOUNT INSTALLATION ***This installation required to have Duct Cover Model No. CH1120DC-1. Figure 9 Preparation before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. - Decide the location of the venting pipe from the hood to the outside. Refer to Figure 9. - A straight, short vent run will allow the hood to perform more efficiently. - Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood.
4. For Rear 3-1/4” x 10” vent installation only: - Remove attached 6” exhaust and discard. (Figure 11) Keep 13 screws to install vent covers. - Remove duct knockout from back of the hood and discard. (Figure 13) Unscrew 3-1/4” x 10” Vent Cover from rear exhaust (located inside hood); keep screws to install 3-1/4” x 10” Exhaust. - Align Top Vent Cover {E} and 3-1/4” x 10” Vent Cover (removed from rear exhaust) using 14 screws (13 screws taken from 6” exhaust).
Figure 17 Wiring to Power Supply CAUTION: If moving the cooking range is necessary to install the hood, turn off the power in an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE BY QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES.
Figure 19 Install Accessories 15. Install the Oil Tunnel {G} into recess support near rear of hood. Refer to Figure 19. 16. Install Baffle Filters {H} and Stainless Steel Spacers {I}. ① Angle baffle filter toward back of hood. ② Push the baffle filter up until almost level. ③ Slide forward into recess behind the front of hood. ④ Lower baffle filter. ⑤ Slide back until it fits into resting position. Refer to Figure 20. 17. For Stainless Steel Spacer, follow above steps. Figure 20 Final Installation 18.
OPERATING INSTRUCTIONS Note: For best results, turn fan on prior to any preparation or cooking and keep fans running while cooking. Adjust speed as needed. To operate the fan function • • Press button to choose from speed. o Q = QuietMode™ speed o L = Low speed o H = High speed Press “OFF” to turn fan off. To operate the light function • Press the Light Control to turn lights on and off.
MAINTENANCE For optimal performance, clean the range hood surface and baffles regularly. To Clean Hood Surface CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. *** Regular care will help preserve its fine appearance. 1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth. 2. If hood looks splotchy (stainless steel hood), use a stainless steel cleaner to clean the surface of the hood. Avoid getting cleaning solution onto or into the control panel.
SPECIFICATIONS MODEL / SIZE Under Cabinet Application CHX9130SQB-1 (30”) CHX9136SQB-1 (36”) Wall Mount Application CHX9130SQB-WM-1 (30”) CHX9136SQB-WM-1 (36”) COLOR 18-Gauge Commercial Grade Stainless Steel CONSUMPTION / AMPERE 232W / 2.
MEASUREMENTS & DIAGRAMS *** All inch measurements are converted from millimeters. Inch measurements are estimated. *** All measurements in ( ) are millimeters. -FOR UNDER THE CABINETMODEL NO.: CHX9130SQB-1 (30”) / CHX9136SQB-1 (36”) 30" = Knockout Holes "A" 36” = Knockout Holes "A" & "B" - FOR WALL MOUNT (DUCT COVER IS INCLUDED– MODEL NO.
***Hood-Mounting Bracket ***Duct Cover-Mounting Bracket ***Duct Cover Support 17
PARTS LIST MODEL NO.: NO. 1 2 3 4 5 CHX9130SQB-1 and CHX9130SQB-WM-1 (30”) CHX9136SQB-1 and CHX9136SQB-WM-1 (36”) DESCRIPTION MODEL /SIZE 6” Exhaust Plate Vent Cover (Top) 2-3/4” x9-3/4” Exhaust Plate 3-3/4” x11-1/4” Vent Cover 6” Round Plastic Exhaust PART NO.
MODEL NO.
CIRCUIT DIAGRAM MODEL NO.
TROUBLE SHOOTING Issue After Installation, both motors and lights are not working. Lights are working, but motor(s) is not. The range hood is vibrating. The motor is working, but the lights are not working. Possible Cause The power is not on. Solution Make sure the circuit breaker and the unit’s power is ON. Use a voltage meter to check the power supply. Check and tighten wire connection. The wire connection is not secure. The control panel is defective. The motor(s) is defective.
WARRANTY WARRANTY CERTIFICATE In order to obtain warranty service, you must provide proof of original purchase from a KOBE authorized Dealer. Please keep a copy of your original invoice as proof of purchase. ONE-YEAR LIMITED LABOR WARRANTY ON KOBE BRILLIA SERIES: For one year from the date of your original invoice from a KOBE authorized dealer, we will repair any parts or components free of charge that failed due to manufacturing defects.
6. Product is purchased from an unauthorized KOBE dealer. 7. Product is damaged due to negligence, misuse, abuse, accident. If we determine that the warranty exclusions listed above applies or if you fail to provide all necessary documentation for warranty service, you will be responsible for all expenses associated with the requested service, including parts, labor, shipping, travelling, and any other expense related to the service request.
WARRANTY INFORMATION FORM Fill in the blanks and keep this paper with the original invoice in a safe place for future service purpose. 1. Date of purchase : 2. Model No. : 3. Serial No. : For warranty service or spare parts purchase contact: KOBE Service Center (USA ONLY) Toll Free: 1-877-BUY-KOBE (289-5623) Email: customer.service@koberangehoods.com For service in Canada and to report a problem, please contact: Phone: 1-626-775-8880 Email: customer.service@koberangehoods.
KOBE Range Hoods 11775 Clark Street Arcadia, CA 91006 USA www.koberangehoods.com This KOBE hood is made for use in the USA and CANADA only. We do not recommend using this hood overseas as the power supply may not be compatible and may violate the electrical code of that country. Using a KOBE hood overseas is at your own risk and will void your warranty. Cette hotte KOBE est fabriquée pour usage aux États-Unis et au Canada seulement.
