KOBE Range Hood Brillia Series Model No.
IMPORTANT READ THIS FIRST READ BEFORE INSTALLATION 1. Carefully check all contents of package(s). 2. Thoroughly inspect the unit for any shipping damages, cosmetic damages or defects. 3. Have a certified contractor/electrician test the unit before installation. IF THERE IS ANY PROBLEM: 1. DO NOT INSTALL THE UNIT AND KEEP ALL ORIGINAL PACKAGING MATERIAL. 2. Have your original invoice as proof of purchase and product serial number ready. 3.
[ENGLISH] - READ AND SAVE THESE INSTRUCTIONS - CONTENTS IMPORTANT SAFETY INSTRUCTIONS.................................................................................... 1 COMPONENTS OF PACKAGE ................................................................................................. 3 INSTALLATION ......................................................................................................................... 4 OPERATING INSTRUCTIONS .........................................................
IMPORTANT SAFETY INSTRUCTIONS - PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION - WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, OBSERVE THE FOLLOWING: 1) Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards, including fire-rated construction. 2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden utilities.
What to Do In The Event Of a Range Top Grease Fire • • • • SMOTHER FLAMES with a tight fitting lid, cookie sheet, or metal tray, and then turn off the burner. KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911. NEVER PICK UP A BURNING PAN – You May Get Burned. DO NOT USE WATER, including wet dishcloths or towels – a steam blast will result.
COMPONENTS OF PACKAGE (Must keep all material for returns or refunds) Range Hood Box {A} KOBE Range Hood {B} Warranty Registration Card {C} Quick Reference Guide {D} Baffle Filter – 2 pcs {E} Oil Tunnel {F} Stainless Steel Spacer – 2 pcs {G} 6” Round Plastic Collar {H} 3-1/4” x 10” Rectangular Exhaust {I} Power Cord {J} Twist-on Wire Connector {K} Screw set {L} Screws Package {G} {H} {I} {J} {A} {L} {K} M4 x 1/2" (18) {B} Adjustable Liner (Sold Separately) Model No.
INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation To calculate installation, please refer to TABLE 1. (All calculation in inches.
Figure 1 Preparation Before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. • Decide the location of the venting pipe from the hood to the outside. Refer to Figure 1. • A straight, short vent run will allow the hood to perform more efficiently. • Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood. • Temporarily wire the hood to test for proper operation before installing.
Figure 5 Hood Preparation Before Installation CAUTION: If moving the cooking range is necessary to install the hood, turn off the power in an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. 14. Choose the required vent option. The Round Exhaust Plate is pre-installed for top vent. 15. For Top 3-1/4” x 10” rectangular installation only: Remove the pre-installed Round Exhaust Plate (Refer to Figure 5).
Figure 9 Duct Work Installation 18. Determine and make all necessary cuts in the wall or ceiling for the ductwork. Note: Install the ductwork before installing the insert. 19. Use steel pipe to connect the exhaust on the hood to the ductwork above. Use duct tape to make all joints secure and air tight. 20. Please refer to local codes for the usage of a damper (not included). Wiring to Power Supply SAFETY WARNING *Note: Sample image only. May not be actual model. RISK OF ELECTRICAL SHOCK.
Figure 13 Final Assembly 29. Install the oil tunnel into recess support near rear of hood. Refer to Figure 12. 30. Install baffle filters. Angle baffle filter toward back of hood ① . Push baffle filter up until almost level ②. Slide forward into recess behind the front of hood ③. Lower baffle filter ④. Slide back until it fits into resting position ⑤. Refer to Figure 13.
OPERATING INSTRUCTIONS 3-Speed Mechanical Control Note: For best results, turn fan on prior to any preparation or cooking and keep fans running while cooking. Adjust speed as necessary. Button Control OFF = Turns the range hood OFF. Q = Lowest fan speed (QuietMode). L = Middle fan speed (Low). H = Highest fan speed (High). = Turns the lights ON/OFF. Power Control To turn the hood off, press the OFF button once while it is ON.
MAINTENANCE For optimal performance, clean the range hood surface and baffles regularly. To Clean Hood Surface CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. *** Regular care will help preserve its fine appearance. 1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth. 2. If hood looks splotchy (stainless steel hood), use a stainless steel cleaner to clean the surface of the hood. Avoid getting cleaning solution onto or into the control panel.
SPECIFICATIONS MODEL / SIZE INX2630SQB-700-3 COLOR Stainless Steel CONSUMPTION / AMPERE 290W / 2.5A VOLTAGE 120V 60Hz NUMBER OF MOTORS 1 FAN TYPE: CENTRIFUGAL Single Horizontal Squirrel Cage EXHAUST Top – 6” Round 3-1/4” x 10” Rectangular Rear – 6” Round 3-1/4” x 10” Rectangular CONTROLS Mechanical Push Button (3-Speed) LIGHTS 3-watt LED light x 2 HOOD DIMENSION (W X D X H) OPTIONAL ACCESSORIES (W X D X H) 30” x 18-1/2” x 12” 2 Piece Adjustable Liner Model No.
MEASUREMENTS & DIAGRAMS All ( ) are in millimeter. All inch measurements are converted from millimeters. Inch measurements are estimated.
Front View Ajustable Stainless Steel Liner (Sold Separately) Model No.
PARTS LIST MODEL NO: INX2630SQB-700-3 NO. DESCRIPTION MODEL/SIZE PART NO.
MODEL NO: INX2630SQB-700-3 15
CIRCUIT DIAGRAM MODEL NO.
TROUBLE SHOOTING Issue After Installation, both motors and lights are not working. Lights are working, but motor(s) is not. Possible Cause The power is not on. The range hood is vibrating. The blower system is not secure. The motor is working, but the lights are not working. LED light fixture(s) is defective. The wire connection is not secure. The control switch is defective. The motor(s) is defective. The capacitor(s) is defective. The control switch is defective.
WARRANTY WARRANTY CERTIFICATE In order to obtain warranty service, you must provide proof of original purchase from a KOBE authorized Dealer. Please keep a copy of your original invoice as proof of purchase. ONE-YEAR LIMITED LABOR WARRANTY ON KOBE BRILLIA SERIES: For one year from the date of your original invoice from a KOBE authorized dealer, we will repair any parts or components free of charge that failed due to manufacturing defects.
6. Product is purchased from an unauthorized KOBE dealer. 7. Product is damaged due to negligence, misuse, abuse, accident. If we determine that the warranty exclusions listed above applies or if you fail to provide all necessary documentation for warranty service, you will be responsible for all expenses associated with the requested service, including parts, labor, shipping, travelling, and any other expense related to the service request.
WARRANTY INFORMATION FORM Fill in the blanks and keep this paper with the original invoice in a safe place for future service purpose. 1. Date of purchase : 2. Model No. : 3. Serial No. : For warranty service or spare parts purchase in US, contact: KOBE Service Center Email (best): customer.service@koberangehoods.com Phone: 1-626-775-8880 ext. 103 Toll Free: 1-877-BUY-KOBE (289-5623) For warranty service or spare parts purchase in Canada, contact: Email (best): customer.service@koberangehoods.
KOBE Range Hoods 11775 Clark Street Arcadia, CA 91006 USA www.koberangehoods.com This KOBE hood is made for use in the USA and CANADA only. We do not recommend using this hood overseas as the power supply may not be compatible and may violate the electrical code of that country. Using a KOBE hood overseas is at your own risk and will void your warranty. Cette hotte KOBE est fabriquée pour usage aux États-Unis et au Canada seulement.