KOBE Range Hoods Model No.
IMPORTANT READ THIS FIRST READ BEFORE INSTALLATION 1. Carefully check all contents of packages. 2. Thoroughly inspect the unit for any shipping damages, cosmetic damages or defects. 3. Have a certified contractor/electrician test the unit before installation. IF THERE IS ANY PROBLEM: 1. DO NOT INSTALL THE UNIT AND KEEP ALL ORIGINAL PACKAGING MATERIAL. 2. Have your original invoice as proof of purchase and product serial number ready. 3.
[ENGLISH] - READ AND SAVE THESE INSTRUCTIONS - CONTENTS IMPORTANT SAFETY INSTRUCTIONS .................................................................................... 1 COMPONENTS OF PACKAGE.................................................................................................. 3 INSTALLATION .......................................................................................................................... 4 OPERATING INSTRUCTIONS........................................................
IMPORTANT SAFETY INSTRUCTIONS - PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION - WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, OBSERVE THE FOLLOWING: 1) Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards, including fire-rated construction. 2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden utilities.
What to Do In The Event Of a Range Top Grease Fire • • • • SMOTHER FLAMES with a tight fitting lid, cookie sheet, or metal tray, and then turn off the burner. KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911. NEVER PICK UP A BURNING PAN – You May Get Burned. DO NOT USE WATER, including wet dishcloths or towels – a violent steam blast will result.
COMPONENTS OF PACKAGE (Must keep all material for returns or refunds) Range Hood Box (Box 1 of 2) {A} {B} {C} {D} {E} {F} {A} KOBE Range Hood {B} Mounting Template {C} Warranty Registration Card {D} Quick Reference Guide {E} Baffle Filters x 3 {F} Screws Package {G} Wire Cap x 3 M4 x 1-1/2” (8) Knob attached to baffle filter {G} Wire caps (3) Duct Cover Box (Box 2 of 2 ) {H} {I} {J} {H} Telescopic Stack {I} Two-Piece Duct Cover {J} Screw Package - FOR MORE INFORMATION, PLEASE VISIT OUR W EBS
INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation To calculate installation, please refer to TABLE 1. (All calculation in inches.
Figure 1 Preparations of Ductwork and Location NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. - Decide the location of the venting pipe from the hood to the outside. Refer to Figure 1. A straight, short venting run will allow the hood to perform more efficiently. Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood. - - Temporarily wire the hood to test for proper operation before installing.
Figure 3 Wiring to Power Supply SAFETY WARNING RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE BY A SPECIALIZED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY. 6. 7. Connect three wires (black, white and green) to house wires and cap with wire connectors.
Figure 5 Hood Installation 11. Place four (4 x 8 mm) temporary screws (provided) to hold the duct cover up. Install the hood as shown in Figure 5. 12. Use eight (3/16x3/8 mm) screws (provided) to secure hood to telescopic stack. Make sure to tighten screws securely. Refer to Figure 5. 13. Connect all the wire connections inside the hood. Install Accessories 14. Place baffle filters underneath the hood Final Assembly 15.
OPERATING INSTRUCTIONS Note: For best results, turn fan on prior to any preparation or cooking and keep fans running while cooking. Adjust speed as needed. Power Control Press Power Control to turn On/Off the range hood. Speed Control The fan will start on Speed #3. Press increase the speed level. button to decrease the speed level. Press button to To activate 3-minute delay shutoff, press and hold button.
ECO Mode can be activated while fan is running or off. Press and hold button until icon briefly appears in the LED Display. While fan is running you can change the speed, use delay shutoff or turn off fan without disabling ECO Mode. When fan is off and ECO Mode has been activated, the icon will appear in the LED Display. The operating on QuietMode™. To deactivate, press and hold appears in the LED Display.
MAINTENANCE SAFETY WARNING NEVER PUT YOUR HAND INTO AREA HOUSING THE FAN WHILE THE FAN IS OPERATING. Cleaning Hood Surface CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. PAPER TOWEL ON STAINLESS STEEL. DO NOT USE For optimal operation, clean range hood and all baffle/spacer/filter/oil tunnel/oil container regularly. *** Regular care will help preserve the appearance of the hood. 1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth. 2.
SPECIFICATIONS MODEL / SIZE For 36” model IS2236SQB-DC16-1 IS2236SQB-DC22-1 IS2236SQB-DC59-1 COLOR Commercial Grade Stainless Steel CONSUMPTION / AMPERE 211W / 1.
MEASUREMENTS & DIAGRAMS All measurements in ( ) are millimeters. All inch measurements are converted from millimeters. Inch measurements are estimated. IS22DC-16-1 Dimension: 16-1/8” (410) MIN IS22DC-22-1 Dimension: 37-3/8” (950) MAX. 22” (559) MIN. IS22DC-59-1 Dimension: 58-6/8“ (1493) MAX.
PART LIST MODEL NO.: For 36” model IS2236SQB-DC16-1 IS2236SQB-DC22-1 IS2236SQB-DC59-1 For 42” model IS2242SQB-DC16-1 IS2242SQB-DC22-1 IS2242SQB-DC59-1 BOX 1of 2 NO. DESCRIPTION 1 LED Light (3W) 2 Control Unit 3 PART NO. L1-0403-0301 L1-0404-6001-A L1-0214-0122 Baffle Filter BOX 2 of 2 NO. DESCRIPTION 4 6” Round Plastic Exhaust (pre-installed) 5 Duct Cover 6 Telescopic Stack 7 Processor Board 8 9 10 MODEL /SIZE MODEL /SIZE IS22DC-22-1 PART NO.
MODEL NO.
CIRCUIT DIAGRAM MODEL NO.
TROUBLE SHOOTING Issue Possible Cause After Installation, both motors and lights are not working. Lights are working, but motor(s) is not. The range hood is vibrating. The power is not on. The motor is working, but the lights are not working. Solution Make sure the circuit breaker and the unit’s power is ON. Use a voltage meter to check the power supply. The wire connection is not secure. Check and tighten wire connection. The motor(s) is defective. Replace the motor. The capacitor(s) is defective.
WARRANTY WARRANTY CERTIFICATE In order to obtain warranty service, you must provide proof of original purchase from a KOBE authorized Dealer. Please keep a copy of your original invoice as proof of purchase. TWO-YEAR LIMITED LABOR WARRANTY ON KOBE PREMIUM SERIES: For two years from the date of your original invoice from a KOBE authorized dealer, we will repair any parts or components free of charge that failed due to manufacturing defects.
4. Incorrect electric current, voltage or wiring. 5. Improper usage of the product such as commercially, outdoor or other usage other than its intended purpose which is residential indoor usage only. 6. Product is purchased from an unauthorized KOBE dealer. 7. Product is damaged due to negligence, misuse, abuse, accident.
WARRANTY INFORMATION FORM W INFORMATION FORM FillWARRANTYARRANTY in the blanks and keep this paper with the original invoice in a safe place for future service purpose. 1. Date of purchase : 2. Model No. : 3. Serial No. : For warranty service or spare parts purchase contact: KOBE Service Center (USA ONLY) Toll Free: 1-877-BUY-KOBE (289-5623) Email: customer.service@koberangehoods.com For service in Canada and to report a problem, please contact: Tel: 1-626-775-8880 Email: customer.
KOBE Range Hoods 11775 Clark Street Arcadia, CA 91006 USA www.koberangehoods.com This KOBE hood is made for use in the USA and CANADA only. We do not recommend using this hood overseas as the power supply may not be compatible and may violate the electrical code of that country. Using a KOBE hood overseas is at your own risk and will void your warranty. Cette hotte KOBE est fabriquée pour usage aux États-Unis et au Canada seulement.