KOBE Brand Range Hood CH00 Series Model No. Under Cabinet: CH0030SQB-1 (30”) CH0036SQB-1 (36”) CH0042SQB-1 (42”) CH0048SQB-1 (48”) Wall Mount: CH0030SQB-WM-1 (30”) CH0036SQB-WM-1 (36”) CH0042SQB-WM-1 (42”) CH0048SQB-WM-1 (48”) RA02 Series Model No.
IMPORTANT READ THIS FIRST READ BEFORE INSTALLATION 1. Carefully check all contents of packages. 2. Thoroughly inspect the unit for any shipping damages, cosmetic damages or defects. 3. Have a certified contractor/electrician test the unit before installation. IF THERE IS ANY PROBLEM: 1. DO NOT INSTALL THE UNIT AND KEEP ALL ORIGINAL PACKAGING MATERIAL. 2. Have your original invoice as proof of purchase and product serial number ready. 3.
[ENGLISH] - READ AND SAVE THESE INSTRUCTIONS - CONTENTS IMPORTANT SAFETY INSTRUCTIONS .................................................................................... 1 COMPONENTS OF PACKAGE.................................................................................................. 3 INSTALLATION .......................................................................................................................... 5 OPERATION INSTRUCTIONS........................................................
IMPORTANT SAFETY INSTRUCTIONS - PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION - WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, OBSERVE THE FOLLOWING: 1) Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards, including fire-rated construction. 2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden utilities.
What to Do In The Event Of a Range Top Grease Fire • • • • SMOTHER FLAMES with a tight fitting lid, cookie sheet, or metal tray, and then turn off the burner. KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911. NEVER PICK UP A BURNING PAN – You May Get Burned. DO NOT USE WATER, including wet dishcloths or towels – a violent steam blast will result.
COMPONENTS OF PACKAGE (Must keep all material for returns or refunds) CH00 {A} {B} {C} {D} {E} {F} {G} {H} {I} {J} Series RANGE HOOD BOX KOBE Range Hood Warranty Registration Card Quick Reference Guide Oil Tunnel Baffle Filter 2 (30” & 36”) 3 (42” & 48”) Spacer x 2 6” Round Plastic Collar (30” & 36”) 8” Round Exhaust Plate (42” & 48”) Screws Package Hood-Mounting Bracket x 2 Screws Package {H} {I} {J} {A} Duct Cover (Included in Wall Mound Hood ONLY) Option Of: Model No.
RA02 Series RANGE HOOD BOX {A} {B} {C} {D} {E} {F} {G} {H} {I} {J} {K} KOBE Range Hood Warranty Registration Card Quick Reference Guide Oil Tunnel Baffle Filter 2 (30” & 36”) 3 (42” & 48”) Spacer 6” Round Plastic Collar (30” & 36”) 8” Round Exhaust Plate (42” & 48”) Screws Package Hood-Mounting Bracket Screws Package Duct Cover (Model No. RA02DC-1) {F} {G} {H} {A} {I} {J} {K} {B} {C} Extension Duct Cover Box (Included in RA02 SQB-DC24-1 Only) {D} {E} {L} Extension Duct Cover (Model No.
INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation Calculate the length of the installation, before installing the hood. (All calculation is measure in inches.
SAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF IT IS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING, CLEANING OR SERVICING. NOTE: BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER, DAMAGE TO THE HOOD MAY OCCUR. CH00 SERIES – UNDER THE CABINET INSTALLATION .................................................................... 7 CH00 SERIES – STAND ALONE INSTALLATION ................................................................................ 9 RA02 SERIES – INSTALLATION .........
CH00 SERIES – UNDER THE CABINET INSTALLATION Figure 1 Preparation before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. Decide the location of the venting pipe from the hood to the outside. Refer to Figure 1. A straight, short venting run will allow the hood to perform more efficiently. Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood.
Ductwork Installation Figure 5 7. Use 6” round steel pipe for 30” and 36” models or 8” round steel pipe for 42” and 48” models (follow building codes in your area) to connect the exhaust on the hood to the ductwork above. Use duct tape to make all joints secure and air tight. Refer to Figure 5. Wiring to Power Supply SAFETY WARNING Figure 6 RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST BE PROPERLY GROUNDED.
CH00 SERIES – STAND ALONE INSTALLATION ***This installation required to have Duct Cover Model No. CH0030DC-12 / CH0036DC-12 / CH0042DC-12 / CH0048DC-12 Preparation before Installation Figure 9 NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. Decide the location of the venting pipe from the hood to the outside. Refer to Figure 9. A straight, short venting run will allow the hood to perform more efficiently.
5. Align hood-mounting bracket to the six screws on the wall and hook hood into place. Tighten screws to secure hood to the wall. 6. For safety purpose, pre-drilled mounting holes are provided through the back of the hood. For a more secure installation, use as many mounting holes as needed to secure from the inside of hood (screws not included). CAUTION: MAKE SURE HOOD SECURE BEFORE RELEASING. Figure 12 IS Wiring to Power Supply SAFETY WARNING RISK OF ELECTRICAL SHOCK.
Figure 13 Duct Cover Installation 8. Use 6” round steel pipe for 30” and 36” models or 8” round steel pipe for 42” and 48” models (follow building codes in your area) to connect the exhaust on the hood to the ductwork above. Use duct tape to make all joints secure and air tight. Refer Figure 13. Slide the duct cover onto the hood. 9. Use 3/16” x 3/8” screws (included) to attach duct cover to hood. Figure 14 Install Accessories 10. Attach oil tunnel. Refer to Figure 14. 11. Refer to Figure 15.
RA02 SERIES - INSTALLATION Figure 16 Preparation before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. Decide the location of the venting pipe from the hood to the outside. (Figure 16) A straight, short venting run will allow the hood to perform more efficiently. Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood.
Hood Installation Figure 19 CAUTION: If required to move the cooking range to install the hood, turn off the power on an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. 1. Using references in Table 2 and measurements on Page 23, mark the leveling locations point for hood-mounting bracket on the wall. 2. Secure two mounting screws (not provided) to the wall, leaving an 1/8” space from the wall. 3.
Figure 22 Duct Cover Installation 6. Use 6” round steel pipe for 30” and 36” models or 8” round steel pipe for 42” and 48” models (follow building codes in your area) to connect the exhaust on the hood to the ductwork above. Use duct tape to make all joints secure and air tight. Refer Figure 20. 7. Use four 4mm x 8mm screws (included) to attach duct cover to hood. Refer to Figure 21. Install Accessories 8. Attach oil tunnel. Refer to Figure 22. 9. Refer to Figure 23.
OPERATION INSTRUCTIONS This KOBE hood is equipped with two rotary controls with powerful centrifugal squirrel cage, baffle filters, and bright LED lights. The two rotary controls are Light Control & Speed Control. Refer to Figure 28. Figure 28 Note: For best results, turn hood to QuietMode™ prior to preparation or cooking to establish airflow in the kitchen. Adjust speed as needed.
MAINTENANCE For the optimal level of operation, clean the range hood surface and baffles regularly. To Clean Hood Surface CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. *** Regular care will help preserve its fine appearance. 1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth. 2. If hood looks splotchy (stainless steel hood), use an orange base cleaner to clean the surface of the hood. Avoid cleaner to get on the control switches.
SPECIFICATIONS CH00 Series MODEL / SIZE For Under Cabinet Application CH0030SQB-1 / 30” / Single Blower CH0036SQB-1 / 36" / Single Blower CH0042SQB-1 / 42” / Dual Blowers CH0048SQB-1 / 48” / Dual Blowers For Wall Mount Application CH0030SQB-WM-1 / 30” / Single Blower CH0036SQB-WM-1 / 36” / Single Blower CH0042SQB-WM-1 / 42” / Dual Blowers CH0048SQB-WM-1 / 48” / Dual Blowers COLOR Commercial Grade Stainless Steel CONSUMPTION / AMPERE CH0030SQB-1 and CH0030SQB-WM-1 – 320W CH0036SQB-1 and CH0036SQB-WM-1 –
SPEED SINGLE BLOWER CH0030SQB-1 CH0036SQB-1 CH0030SQB-WM-1 CH0030SQB-WM-1 DUAL BLOWERS CH0042SQB-1 CH0048SQB-1 CH0042SQB-WM-1 CH0042SQB-WM-1 QuietMode Low High Air Capacity (cfm) Sone* 300 1.8 580 4.7 760 5.4 Air Capacity (cfm) Sone* 450 2.5 800 6.0 1200 8.0 *One sone is equivalent to the sound of a refrigerator at 40 decibels. **Specifications subject to change without notice.
RA02 Series MODEL / SIZE RA0230SQB-1 or RA0230SQB-DC-1 / 30” / Single Blower RA0236SQB-1 or RA0236SQB-DC-1 / 36” / Single Blower RA0242SQB-1 or RA0242SQB-DC-1 / 42” / Dual Blowers RA0248SQB-1 or RA0248SQB-DC-1 / 48” / Dual Blowers RA0230SQB-DC24-1 / 30” / Single Blower RA0236SQB-DC24-1 / 36” / Single Blower RA0242SQB-DC24-1 / 42” / Dual Blowers RA0248SQB-DC24-1 / 48” / Dual Blowers COLOR Commercial Grade Stainless Steel CONSUMPTION / AMPERE RA0230SQB-1 or RA0230SQB-DC-1 – 320W RA0236SQB-1 or RA0236SQB-
Net Gross RA0230SQB-1 or RA0230SQB-DC-1 RA0236SQB-1 or RA0236SQB-DC-1 RA0242SQB-1 or RA0242SQB-DC-1 RA0248SQB-1 or RA0248SQB-DC-1 RA02DC-1 55 60 75 79 67 74 91 97 5 7 QuietMode Low High Air Capacity (cfm) Sone* 300 580 760 1.8 4.7 5.4 Air Capacity (cfm) Sone* 450 800 1200 2.5 6.0 8.
MEASUREMENTS & DIAGRAMS *** All inch measurements are converted from millimeters. Inch measurements are estimated. *** All measurements in ( ) are millimeters. CH00 Series - FOR UNDER THE CABINET – MODEL NO.: CH0030SQB-1 (30”) CH0036SQB-1 (36”) CH0042SQB-1 (42”) CH0048SQB-1 (48”) - FOR STAND ALONE – MODEL NO.
- FOR STAND ALONECH00 Series MODEL NO.
*** All inch measurements are converted from millimeters. Inch measurements are estimated. *** All measurements in ( ) are millimeters. RA02 Series MODEL NO.
PARTS LIST CH00 Series MODEL NO.: CH0030SQB-1 and CH0030SQB-WM-1 (30”) CH0036SQB-1 and CH0036SQB-WM-1 (36”) CH0042SQB-1 and CH0042SQB-WM-1 (42”) CH0048SQB-1 and CH0048SQB-WM-1 (48”) NO.
CH00 Series Model No.
CH00 Series Model No.
PART LIST RA02 Series MODEL NO.: RA0230SQB-1 / RA0230SQB-DC-1 / RA0230SQB-DC24-1 (30”) RA0236SQB-1 / RA0236SQB-DC-1 / RA0236SQB-DC24-1 (36”) RA0242SQB-1 / RA0242SQB-DC-1 / RA0242SQB-DC24-1 (42”) RA0248SQB-1 / RA0248SQB-DC-1 / RA0248SQB-DC24-1 (48”) NO. DESCRIPTION MODEL /SIZE PART NO.
RA02 Series Model No.
RA02 Series Model No.
CIRCUIT DIAGRAM MODEL NO.: CH0030SQB-1 and CH0030SQB-WM-1 (30”) CH0036SQB-1 and CH0036SQB-WM-1 (36”) RA0230SQB-1 / RA0230SQB-DC-1 / RA0230SQB-DC24-1 (30”) RA0236SQB-1 / RA0236SQB-DC-1 / RA0236SQB-DC24-1 (36”) MODEL NO.
TROUBLE SHOOTING Issue After Installation, both motors and lights are not working. Possible Cause The power is not on. The wire connection is not secure. The control panel is defective. Solution Make sure the circuit breaker and the unit’s power is ON. Use a voltage meter to check the power supply. Check and tighten wire connection. Replace the control panel. Lights are working, but motor(s) is not. The motor(s) is defective. The capacitor(s) is defective. The control panel is defective.
WARRANTY WARRANTY CERTIFICATE KOBE Range Hoods (referred to herein as “we” or “us”) warrants to the original purchaser (referred to herein as “you” or “your”) all products manufactured or supplied by us to be free from defect in workmanship and materials as follows: TWO-YEAR LIMITED WARRANTY FOR PARTS AND LABOR ON KOBE PREMIUM SERIES: For two years from the date of your original invoice from a KOBE authorized dealer, we will, at our sole discretion, choose to repair or replace the product free of charge th
If we determine that the warranty exclusions listed above apply or if you fail to provide all necessary documentation for warranty service, you will be responsible for all expenses associated with the requested service, including parts, labor, shipping, travelling and any other expense related to the service request. To qualify for warranty service, you must: 1. 2. 3. 4. 5.
WARRANTY INFORMATION FORM Fill in the blanks and keep this paper with the original invoice in a safe place for future service purpose. 1. Date of purchase : 2. Model No. : 3. Serial No. : For warranty service or spare parts purchase contact: KOBE Service Center (USA ONLY) Toll Free: 1-855-800-KOBE (5623) Email: kobe@adcoservice.com For service in Canada and to report a problem, please contact: Tel: 1-626-775-8880 Email: customer.service@koberangehoods.
KOBE Range Hoods 11775 Clark Street Arcadia, CA 91006 USA www.koberangehoods.com This KOBE hood is made for use in the USA and CANADA only. We do not recommend using this hood overseas as the power supply may not be compatible and may violate the electrical code of that country. Using a KOBE hood overseas is at your own risk and will void your warranty. Cette hotte KOBE est fabriquée pour usage aux États-Unis et au Canada seulement.