User's Guide

Qi Wireless Charging
1. Place your wireless device on top of the tray. Charging
will begin on contact.
2. When wireless charging, the LED indicator is continu-
ously solid green.
3. There is a protective circuit that detects when foreign
objects or devices that are not Qi certified are placed on
the charging and will disable power to the charger as a
safety precaution. When triggered the LED indicator will
flash red and green.
NOTE: works with Qi devices including: iPhone 8, iPhone X
iPhone XS, iPhone XR or newer iPhone models, compatible
Android and Google Pixel phones.
USB Charging Mobile Devices
Connect the charging cable of your 5V devices to the USB
port at the front of the clock, then connect the other end to
your device. Your clock supplies 1A of power and will
charge you phone or other devices automatically.
NOTE: Charging cables for your device are not included.
Adjusting the Display Brightness
Tap SNOOZE to adjust the brightness of the LED backlight.
NOTE: This can only be done when the adapter is being
used to power the clock. If only the backup batteries are
being used to power the clock, press SNOOZE to turn on
the backlight for 10 seconds and then it will go off again.
Troubleshooting
If your clock is not functioning properly, it may be caused
by electro-static discharge or other interference.
Unplug the DC jack and remove backup batteries, plug the
DC jack to the clock. Reinstall the backup batteries after 10
seconds.
Your clock will reset to default settings and you will need to
set it again.
Setting Time
1. On the top of the clock, press and hold , the hour
digits “12” will flash. Press + or - to set the hours. (You
can hold down to change the time faster.) As you cycle
through, the hours will change from AM to PM.
2. Press again, the minutes digits “00” will flash. Press +
or - to set the minutes.
4. Press again to exit the setup (or if no key pressed for
about 10 seconds it will automatically exit the setup).
Qi Wireless Charging Tray Clock
User’s Guide
CA-80WC
Product Care
1. Place your clock away from areas with direct sunlight,
excessive heat or moisture.
2. Protect your furniture when placing your clock on a natural
wood and lacquered finish by using a cloth or protective
material between it and the furniture.
3. Clean your clock with a soft cloth moistened only with mild
soap and water. Stronger agents such as Benzine, thinner or
similar materials can damage the surface of the unit.
4. Do not use old or used battery in your clock.
5. If the clock is not to be used for over a month or longer,
remove the battery to prevent possible corrosion. If the battery
compartment become corroded or dirty, clean the compartment
and replace with new battery.
Specifications
Alarm duration: 60 minutes (buzzer)
Snooze duration: 5-60 minutes (buzzer)
Defaults:Time - 12:00AM ; Alarm 1 & 2 - 6:00AM Snooze - 5 minutes
Power: The output of the provided AC/DC adapter is 5V/2A
FCC Disclaimer
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Installation
Plug in the AC/DC power adapter to an AC wall outlet and
then plug its DC jack into the back of the clock. Your clock
will turn on and is now ready to use.
Backup Battery Installation
1. Slide to remove the battery cover on the bottom of the
clock.
2. Insert 2 new AA batteries (not included) with “+” and
“-” ends of battery aligned as indicated (the “-” side of
the battery touches the contact spring on your clock).
3. Replace the battery cover.
• Do not mix old and new batteries.
• Do not mix alkaline, standard and rechargeable batteries.
• Alkaline batteries are recommended
HELLO,
Thanks for choosing Capello. We’re a small team
that believes in the simple joy of nicely designed
products. If you need a hand, we’re here to help
you:
[e-mail]
A little story from the designer:
I remember going to the science museum in
Pittsburgh as a kid and seeing the electric arc
between my hand and the Van de Graaff
generator. Electricity though the air was like
holding lightning. Wireless charging has been a
long time coming to phones and it’s so cool and
convenient to simply set your phone down and
have it charge. Welcome to the future!
Enjoy, Matthew
SNOOZE
BRIGHTNESS
ADJUST
TIME SET
ALARM 1 /ALARM 2
INDICATORS
ALARM 2
ON-OFF / SET
+ TIME ADJUST
- TIME ADJUST
ALARM 1
ON-OFF / SET
TIME
AM / PM INDICATORS
Qi WIRELESS
CHARGING INDICATOR
USB CHARGING PORTDC POWER JACK
BATTERY COVER UNDER CLOCK
(BATTERIES NOT INCLUDED)
Setting the Alarm
1. Press and hold , the hour digit will flash. Press + or -
to set the alarm hour. (You can hold down to change the
time faster.) As you cycle through, the hours will change
from AM to PM.
2. Press again, the alarm minutes digit will flash. Then
press + or - to set alarm minutes.
3. Press again, the snooze time “05” will flash. Then
press + or - to set snooze duration from 5-60 minutes.
4. Press to exit the setup (or if no key pressed for about
10 seconds it will automatically exit the setup).
Repeat the same procedure using to set Alarm 2.
Using the Alarm
1. Press once to activate Alarm 1 and the icon will
show on the display.
2. Press again to turn Alarm 1 off and the icon will
disappear from the display.
Repeat the same procedure using to set Alarm 2.
Note: The Snooze duration is set during the alarm setup.
When the Alarm Sounds
To SNOOZE , tap the top of Sleep & Charge to snooze
the alarm. The Snooze duration is set during the alarm
setup.
To stop the alarm and reset it to sound again tomorrow,
press any button on the top of your clock (besides the
Snooze button). The alarm will stop buzzing and will be
set to sound again tomorrow.
Qi Wireless Charging Tray