Full Product Manual

Important Safety Instructions:
Please read the following safety information before attempting to assemble, operate or
install the product. To reduce risk of fire, electric shock, or injury to persons:
• CAUTION: Turn OFF the main power at the fuse or circuit breaker before installing the
lighting fixture or making any electrical connection. You may use a non-contact
voltage tester to ensure no power is running to the wires.
• CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified electrician to
ensure correct branch circuit conductor.
• WARNING: If any special control devices are used with this fixture, follow instructions
carefully to assure full compliance with N.E.C. requirements. If there are any
questions, contact a qualified electrical contractor.
• Make sure this lighting fixture is adequately grounded. To ensure proper grounding,
there must be a separate ground wire (bare copper) contact between this lighting
fixture and the ground connection of your main power supply panel. Do not connect
the bare or green insulation fixture ground wire to the black (hot) current-carrying
wire or the white (neutral) wire. Connection of the bare or green fixture ground wire
to the black or white wires may cause metal parts of the fixture to carry electrical
currents, and may cause electrical shock, which could cause serious injury or death.
• Do not connect this fixture to an electrical system that does not provide a means for
equipment grounding. Never use a fixture in a two-wire system that is not grounded.
Installing a fixture into an electrical system not having a proper grounding could
cause metal parts of the fixture to carry electrical currents if any of the fixture wires,
wire connections, or splices were to become broken, cut, or loose during the
mounting or normal operation of the fixture. Under this condition, anyone coming in
contact with the fixture would be subject to electrical shock, which could cause
serious injury or death.
• CAUTION: A loose wire increases the risk of fire; tighten all connections securely.
• Do not suspend any fixture by the house wires. Suspending a fixture by the house
wires and wire connectors may result in the fixture falling, possibly causing personal
injury and the danger of electrical shock or fire.
• The fixture must be installed by qualified electrician. All electrical connections must
be in accordance with all national and local electrical codes
• CAUTION: All glass is fragile. Use care when handling glass shades and bulbs.
Tools Needed (not included):
Please lay out all parts and read the instructions prior to installation.
PACKAGE CONTAINS:
PREPARATION
INSTALLATION：
3 x Wire Nuts 2 x Quick Chain Links
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION
OF THE PRODUCT AND THE HAZARDS INVOLVED
1. Detach the screw collar from chain
holder. Mount the Crossbar kit together
with the Chain holder using the
Mounting Screws.
INSTALLATION PROCEDURE:
2 3
54 6
WILLIAMS OUTDOOR HANGING
SINGLE PENDANT LIGHT
IMPORTANT INFORMATION.
PLEASE READ CAREFULLY AND RETAIN FOR FUTURE REFERENCE
Model: LM030161
For assistance with assembly, installation, parts or customer service,
please contact us:
[e-mail]
1-866-294-9244, Monday to Friday, 8am to 5pm Pacific Time
2975 Red Hill Ave., Suite 100, Costa Mesa, CA 92626, USA
Safety Glasses
Carefully remove the lighting fixture, LED bulb and mounting accessories from the box, and
check that all parts are included using the contents diagrams below. Do not attempt to
assemble the product if any part(s) is missing or damaged. Please contact Koda customer
support if this is the case.
1 x Hanging
Coach Light
1 x Canopy
1 x 36” Chain
Wire Stripper
2 x Bracket Mounting Screws
1 x Crossbar Kit,
1x Chain Holder with Screw Collar
1 x LED Bulb
2. Attached the Canopy to the ceiling using
the Screw collar.
3. Connect the Quick Chain Link to the
Chain Holder. Determine the height you
want to hang the fixture down from the
ceiling. Use a pair of pliers to twist to open
the chain link end and remove the
unwanted portion of Chain. Connect the
wanted Chain to the Quick Chain Link.
Twist to close both opened Chain Links.
Philips and Flat Head
Screwdrivers
Wire Nut
Installation Kit: LED Bulb:
Hanging Coach Light:
2 x Pliers
4. Connect the Fixture and the Chain with
the Quick Chain Link.
5. Determine the length of wires you need
and use a wire stripper tool to cut and strip
the wires. Then weave the wires through
the Chain, Unlock the Collar and release
the Canopy to pass the wires through the
hole on the chain holder and Cross bar as
shown in the diagram.
Bracket Mounting Screw
Canopy
Screw Collar
Hanging Coach Light
Chain Holder
36” Chain
Quick Chain Link
LED Bulb
Crossbar Kit