Instructions / Assembly

Important Safety Instructions:
Please read the following safety information before attempting to assemble, operate or
install the product. To reduce risk of fire, electric shock, or injury to persons:
• CAUTION: Turn OFF the main power at the fuse or circuit breaker before installing the
lighting fixture or making any electrical connection. You may use a non-contact
voltage tester to ensure no power is running to the wires.
• CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified electrician to
ensure correct branch circuit conductor.
• WARNING: If any special control devices are used with this fixture, follow instructions
carefully to assure full compliance with N.E.C. requirements. If there are any
questions, contact a qualified electrical contractor.
• Make sure this lighting fixture is adequately grounded. To ensure proper grounding,
there must be a separate ground wire (bare copper) contact between this lighting
fixture and the ground connection of your main power supply panel. Do not connect
the bare or green insulation fixture ground wire to the black (hot) current-carrying
wire or the white (neutral) wire. Connection of the bare or green fixture ground wire
to the black or white wires may cause metal parts of the fixture to carry electrical
currents, and may cause electrical shock, which could cause serious injury or death.
• Do not connect this fixture to an electrical system that does not provide a means for
equipment grounding. Never use a fixture in a two-wire system that is not grounded.
Installing a fixture into an electrical system not having a proper grounding could
cause metal parts of the fixture to carry electrical currents if any of the fixture wires,
wire connections, or splices were to become broken, cut, or loose during the
mounting or normal operation of the fixture. Under this condition, anyone coming in
contact with the fixture would be subject to electrical shock, which could cause
serious injury or death.
• CAUTION: A loose wire increases the risk of fire; tighten all connections securely.
• Do not suspend any fixture by the house wires. Suspending a fixture by the house
wires and wire connectors may result in the fixture falling, possibly causing personal
injury and the danger of electrical shock or fire.
• The fixture must be installed by qualified electrician. All electrical connections must
be in accordance with all national and local electrical codes
• CAUTION: All glass is fragile. Use care when handling glass shades and bulbs.
Tools Needed (not included):
Please lay out all parts and read the instructions prior to installation.
PACKAGE CONTAINS:
PREPARATION
INSTALLATION：
3 x Wire Nuts
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION
OF THE PRODUCT AND THE HAZARDS INVOLVED
1. Loosen and remove the Ball Nuts from
the Round Mounting Plate, set them aside.
INSTALLATION PROCEDURE:
Black (hot) wire to the hot supply wire
(most likely black or colored).
White (neutral) wire to the neutral supply
wire (most likely white).
Bare copper (ground) wire to the supply
ground wire (most likely bare copper,
green wire, or green and yellow wire), or
wrap around the ground screw if ground
wire does not exist.
Screw the wire nuts in a clockwise
direction until tight. Make sure no bare
wire or wire strands are visible after
making the connections. Check for
tightness by pulling wires.
5. Make the following spliced wire
connections using wire nuts:
2 3
54 6
FARMER SINGLE PENDANT LIGHT
IMPORTANT INFORMATION.
PLEASE READ CAREFULLY AND RETAIN FOR FUTURE REFERENCE
Model: LM030224
For assistance with assembly, installation, parts or customer service,
please contact us:
[e-mail]
1-866-294-9244, Monday to Friday, 8am to 5pm Pacific Time
2975 Red Hill Ave., Suite 100, Costa Mesa, CA 92626, USA
Safety Glasses
Carefully remove the lighting fixture, LED bulb and mounting accessories from the box, and
check that all parts are included using the contents diagrams below. Do not attempt to
assemble the product if any part(s) is missing or damaged. Please contact Koda customer
support if this is the case.
1 x Cage Shade
Fixture Mounting Screw
Bracket Mounting Screw
Lamp Cord
Lamp Holder
Socket Ring
1 x Canopy, Lamp Cord,
Lamp Holder and Socket Ring
Wire Stripper
2 x Bracket Mounting Screws
1 x Round Mounting Plate,
2 x Fixture Mounting Screws,
2 x Hex Nuts with 2 x Ball Nuts
1 x LED Bulb
2. Pull the power supply wires out from
the outlet box and install the Round
Mounting Plate to the outlet box using the
Bracket Mounting Screws included.
3. Loosen the flat head screw on the
Canopy and adjust the Lamp Cord to your
desired length.
Philips and Flat Head
Screwdrivers
4. Cut the excessive length of the Lamp
Cord with a Wire Stripper and reserve a
length above the Canopy enough for the
hardwire connection.
Cage Shade
LED bulb
Canopy
Round Mounting Plate
Hex Nut
Ball Nut
Wire Nut
Installation Kit: LED Bulb:
Farmer Single
Pendant Light:
Black (hot) Supply Wire
White (neutral) Supply Wire
Supply Ground Wire