Front 2 1 3 4 5 1. Air Vents 2. Cover Release 3. Top Cover 4. Operator Panel 5. Print Exit Slot 6. Print Catcher 7. Trim Tray 7 6 Back 8 8. USB Port 9. Data Plate 10. Power Connector 11. Power Switch 12.
Internal View 1 2 3 4 1. Thermal Print Head 2. Peel Plate 3. Cleaning Roller 4.
Table of Contents 1 Setting Up the Printer Package Contents .............................................................................................................................................1-1 Before You Begin .............................................................................................................................................1-2 Recommended Air Flow Clearances ...........................................................................................................
Table of Contents Appendix A: Important Printer Information System Requirements .......................................................................................................................................A-1 Printer Specifications .......................................................................................................................................A-1 Printer Supplies .................................................................................................................
1 Setting Up the Printer Package Contents The KODAK 605 Photo Printer is packaged with the following items: 1 8 2 7 3 4 6 5 1. Printer 2. KODAK Thermal Printer Cleaning Kit 3. Trim Tray (not installed) 4. Print Catcher (not installed) 5. Power Cable 6. USB Cable 7. Paper Flange with gear (Green) 8. Paper Flange with out gear (Black) 9. User Guide and software CD, not pictured (The User Guide is provided on the CD, and not in printed form.
Setting Up the Printer Before You Begin IMPORTANT: The printer is shipped with several power cables. Be sure to use the correct power cable for your country. Have the following items available before you begin your printer setup: • KODAK Photo Print Kit 6800/4R or KODAK Photo Print Kit 6800/6R which contains the correct paper and ribbon for the best print quality and print life from your printer. See Appendix A for details on the Photo Print Kit (sold separately). • USB cable (included).
Setting Up the Printer Removing the Packing Material Keep the carton and packing inserts for repacking and transporting the printer. 1. Remove the tape from the top cover and paper door. 2. Slide the cover release toward you. IMPORTANT: The cover does not open beyond a 90° angle. 3. Open the top cover carefully. 4. Remove the packing material.
Setting Up the Printer Installing the Trim Tray CAUTION: There are sharp cutter blades inside the printer. Do not insert hands or objects. The trim tray collects paper trimmings that are generated when the printer cuts the prints. 1. Insert the trim tray into the printer as shown. 2. To keep your prints dust-free and to prevent paper jams, empty the trim tray each time you change the paper.
Setting Up the Printer Connecting the Cables Connecting the Power If you received more than one power cable with your printer, make sure to use the correct power cable for your country. Cable 1. Check that the power switch is turned off ( ). CAUTION: The power outlet must be grounded. An ungrounded outlet can cause fire, electric shock, or harmful interference to nearby electrical devices. 2. Connect the power cable to the power connector on the back of the printer and to a grounded power outlet.
Setting Up the Printer Loading the Ribbon Make sure that you have a KODAK Photo Print Kit 6800/4R or KODAK Photo Print Kit 6800/6R available. These kits contain the correct size ribbon for your printer. See Appendix A for details on the Photo Print Kits (sold separately). NOTE: Images remain on the ribbon after printing. If you need to maintain confidentiality, dispose of the used ribbon appropriately. 1. If you are replacing a ribbon, remove the used ribbon. 2.
Setting Up the Printer 6. Remove the label. Take-up spool 7. Insert the right side of the take-up spool into the spool holder on the right. 8. Insert the left side of the take-up spool in the spool holder on the left. 9. Adjust the take-up spool until the spool locks into the spool holder. IMPORTANT: Slack in the ribbon can cause a paper jam. 10. Turn the supply spool to remove any slack in the ribbon. 11. Close the top cover. Turning On the Printer 1. Press the power switch to on ( | ).
Setting Up the Printer Loading the Paper Make sure that you have a KODAK Photo Print Kit 6800/4R or KODAK Photo Print Kit 6800/6R available. These kits contain the correct size paper for your printer. See Appendix A for details on the photo print kits (sold separately). 1. Make sure that the printer power is on ( | ). 2. Remove the plastic from the new paper roll. IMPORTANT: Do not remove the label from the paper roll until you have successfully loaded the paper in the printer. 3.
Setting Up the Printer 5. Carefully lower the paper roll into the slots. Match the geared flange Label (green) with the geared slot (green) on the printer. 6. Remove the label from the paper roll. NOTE: Verify that the paper unrolls from the top of the roll. Slot 7. Feed the paper into the rear printer slot until the red LED light turns off and the green LED light turns on. 8. Close the paper door. NOTE: Ribbon must be loaded in the printer before the paper automatically advances.
Setting Up the Printer Making a Test Print Make a test print to check that the printer is installed and set up correctly. 1. Press Menu twice until Test Print Mode appears. 1 2. Press Enter to start printing the test print. For more information on using the operator panel in Setup mode, see “Using Setup Mode to Review Printer Settings” on page 2-2. 2 Online User Guide This User Guide and the Quick Setup Guide are also provided on the CD that came with your printer.
2 Operating the Printer Making Prints You make prints using photo printing software applications. For application-specific printing information, see the user’s guide or online Help for the software application. Handling and Storing Prints For best results: • Make sure hands are clean and free of food, oil, and grease. • Store prints in a cool, dry environment free of chemical contamination. • Store prints at temperatures below 72° F (25° C) for extended periods.
Operating the Printer Understanding the Operator Panel Lights Light Color Printer Status Power Orange The printer power is on. Ready Green The printer is ready to make prints. Error Red An error has occurred. See the message on the operator panel, then see “Resolving Operator Panel Error Messages” on page 4-2. Using Setup Mode to Review Printer Settings Use the operator panel to review printer settings in Setup mode. Printer settings are displayed here 1,2 3 4 5 1.
Operating the Printer Accessing the Printer Settings Press Menu repeatedly to scroll through the printer settings in the following order. Printer Setting Operator Panel Display Action Required Printer ready Ready None. The printer is on and ready to make prints. Changing energy save mode Energy Save Mode Press Enter to turn Energy Save Mode on or off. The default is off. When turned on, the printer goes into a standby mode after 30 minutes, using less power.
Operating the Printer Printer Setting Operator Panel Display Action Required Changing the wait time Press Enter to change wait time from 0 to 100 seconds. The default is 1 second. This only applies when printing 4R prints using 6R ribbon. The wait time is the length of time that the printer waits before it starts printing after receiving a 4R print. This allows the printer to receive a second 4R print that will print at the same time as the first 4R print.
3 Maintaining the Printer To ensure good printer performance and high-quality prints, make sure that the KODAK 605 Photo Printer and its environment are clean and dust free. Cleaning the Printer Clean the exterior of the printer and the filter openings regularly to eliminate dust buildup and prevent dirt from entering the printer. CAUTION: Never use abrasives or harsh chemicals to clean any part of the printer. Do not allow any foreign objects or liquids to fall or spill inside the printer.
Maintaining the Printer CAUTION: Alcohol is a flammable liquid. It can cause eye irritation and dry skin. Prolonged or repeated skin contact may cause drying, cracking or irritation. Wash your hands with soap and water following any maintenance procedures where you use alcohol pads. For additional information, see the Material Safety Data Sheet (MSDS). In the United States for information on health related issues, call 585-722-5151. Customers outside the U.S.
Maintaining the Printer Cleaning the Platen Roller Platen Roller 1. Remove an alcohol pad from its packaging. Wipe the rubber section of the platen roller with the pad. 2. Rotate the roller to clean the entire surface. 3. Allow the alcohol to dry completely (about five minutes) before you resume printing. 4. Close the top cover. Cleaning the Cleaning It is essential to keep the cleaning roller clean to prevent dirt from transferring back onto the prints and to keep the printer operating correctly.
4 Troubleshooting Resolving Potential Problems Problem Description or Cause Possible Solution Paper jam; error light is on, printer does not operate Paper is jammed in the printer Clear the paper jam. See “Clearing a Paper Jam” on page 4-3. Prints have vertical streaks Thermal print head is dirty. If directed by your Kodak service representative, clean the thermal print head. See “Cleaning the Thermal Print Head and the Peel Plate Edge” on page 3-2.
Troubleshooting Resolving Operator Panel Error Messages Refer to the following table to resolve errors reported on the operator panel. If the problem persists, contact your Kodak service representative. Error Message Description or Cause Possible Solution Paper Empty The paper is empty or is not loaded. Load the paper. See “Loading the Paper” on page 1-8. Check Ribbon The ribbon is empty, is not loaded, or is stuck to the paper. Load the ribbon. See “Loading the Ribbon” on page 1-6.
Troubleshooting Clearing a Paper Jam 1. Press and hold Paper Rewind until the Paper Empty message appears. 2. Once the Paper Empty message appears: – – – – Open the paper door. Cut off any damaged or printed areas of the paper. Load the paper. See “Loading the Paper” on page 1-8. If the operator panel displays the Ready message, the jam is cleared. 3. If the Paper Jam message is still displayed on the operator panel: – – – – Turn off the printer. Open the paper door. Open the top cover.
Troubleshooting 5. Cut off any damaged or printed areas of the paper. NOTE: Do not damage or mark any of the rollers. 6. Look inside the printer and carefully remove any pieces of paper. 7. Turn on the printer. 8. Load the ribbon. See “Loading the Ribbon” on page 1-6. 9. Close the top cover. 10. Load the paper. See “Loading the Paper” on page 1-8.
Appendix A: Important Printer Information System Requirements • Computer with MICROSOFT WINDOWS XP, WINDOWS 2003 Server, WINDOWS VISTA Operating System • Minimum 1.0 GHz Celeron Microprocessor • Minimum memory requirement is determined by your operating system • Minimum 2 GB of available hard disk space • USB High Speed (2.0) compliant host device Printer Specifications Dimensions 17.4 in. (44.1 cm) 25.2 in. (64.1 cm) 19 in. (48.
Important Printer Information Printer Supplies Paper and Ribbon Each Photo Print Kit contains the correct media set (roll-feed paper and ribbon) for your printer model. Photo Print Kits are sold separately. IMPORTANT: For best results, replace both the paper and ribbon at the same time. Used ribbon is safe for land-fill disposal. Do not recycle used ribbon.
Important Printer Information Thermal Printer Cleaning Kit Use the KODAK Thermal Printer Cleaning Kit when performing routine maintenance on the printer (see page 3-1). One Thermal Printer Cleaning Kit is included with your printer. KODAK Thermal Printer Cleaning Kit Catalog number 172-1117 Contents Individually packaged alcohol pads (10) CAUTION: Alcohol is a flammable liquid. It can cause eye irritation and dry skin.
Appendix B: Safety and Regulatory Information Important Safety Information CAUTION: Use of controls or adjustments or performance of procedures other than those specified in this manual may result in injury and/or damage to the printer. • The power outlet should be easily accessible and installed near the printer. • Position the power cable so that it cannot be pulled on or tripped over. • Never allow the power cable to contact hot surfaces. • The power outlet must be grounded.
Safety and Regulatory Information Safety Labels Please observe the important safety warnings that are posted on the printer. P/N 2J5451 1641132182 CAUTION HOT SURFACE To avoid burns, use caution when closing the cover. P/N 2J5452 1641132183 CAUTION SHARP OBJECTS The metal edges of the printer may be sharp. P/N 2J5439 1641132233 CAUTION SHARP CUTTER BLADE There are sharp cutter blades inside the printer. Do not insert hands or objects. This label is posted behind the trim tray.
Safety and Regulatory Information Regulatory and Safety Compliance Safety Complies with UL 60950-1:2003 CAN/CSA C22.2 No. 60950-1-03 EN 60950-1:2001 IEC 60950-1:2001 Tested for Norwegian IT Power systems 240V phase to phase Electromagnetic Compatibility (EMC) NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules.
Safety and Regulatory Information CAUTION: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. “Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.” Install and use the equipment according to the instruction manual.
Safety and Regulatory Information Noise Emission The operator-position noise emission value is less than 70 dB(A).* * Average value specified in accordance to JIS Z8731 Disposal This product contains a small amount of lead in the solder on the circuit boards. Disposal of this material may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities. In the USA, contact the Electronics Industry Alliance at www.eiae.org.
Safety and Regulatory Information China RoHS Environmental Protection Use Period (EPUP) In China, this number indicates the time period (in years) within which any hazardous substances present in the product are not expected to be released such that there is risk to human health, property, or the environment. This value is assigned based on normal use of the product as described in the operating instructions.
Index A air flow clearances, 1-2 B bar code, ribbon, 1-6 C cable connecting, 1-5 power, 1-1—1-2, 1-5 position of, B-1 USB, 1-1 checking paper status, 2-3 ribbon status, 2-3 cleaning cleaning rollers, 3-3 cleaning rollers, cleaning, 3-3 clearances for air flow, 1-2 clearing paper jam, 4-3 connecting cables, 1-5 contents, package, 1-1 D disposal, printer, B-5 E Electronics Industry Alliance, B-5 EMC directive, compliance with, B-3 error messages operator panel, 4-2 F filter openings blocking, B-1 cleaning, 3-
Index loading paper, 1-8—1-9 ribbon, 1-6—1-7 M maintaining the printer, 3-1 maintenance cleaning rollers, 3-3 KODAK Thermal Printer Cleaning Kit, A-3 performing routine, 3-1 Material Safety Data Sheet, 3-1 N noise emission spec, B-5 O online user guide, 1-1, 1-10 operator panel error messages, 4-2 lights, 2-2 making a test print, 2-3 printer settings, 2-3 Ready message, 2-3, 2-4 setup mode, 2-3 ordering supplies, A-2 P package contents, 1-1 packing material, removing, 1-3 packing the printer, A-3 paper han
Index prints, 2-1 ribbon, A-2 supplies, printer, A-2 supply spool, 1-6 switch, power, 1-7 system requirements, A-1 T takeup spool, 1-7 temperature paper and ribbon specifications, A-2 printer specifications, A-1 test print, making, 1-10 thermal print head cleaning, 3-1, 3-2, 4-1 transporting the printer, A-3 trim tray, 1-1 cleaning, 3-1 installing, 1-4 troubleshooting clearing paper jam, 4-3 error messages, operator panel, 4-2 power interruption, 4-4 U unpacking, 1-3 USB cable, 1-1 connecting, 1-5 USB conn
