User Manual
BEFORE YOU START Declaration of Conformity Responsible Party: JK Imaging Ltd. Address: 1411 W. 190th Street, Suite 550, Gardena, CA 90248, USA JK Imaging Europe, 71 Clarendon road, Watford, WD17 1DS, UK Company Website: www.kodakpixpro.com For Customers in the U.S.A. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE This device complies with part 15 of the FCC Rules.
About this Manual Thank you for purchasing this KODAK PIXPRO Digital Camera. Please read this manual carefully and keep it in a safe place for future reference. JK Imaging Ltd. reserves all rights of this document. No part of this published manual may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form, by any means, without the prior written permission of JK Imaging Ltd..
SAFETY NOTES Safety notes for this camera Do not drop the camera or allow it to hit solid objects. Do not attempt to disassemble the camera. To prevent the camera from being damaged by moisture, do not use or store the camera in very humid environments, such as in rain or near bodies of water. Do not use or store the camera in dusty places or on a beach to prevent dust or sand from entering the camera, causing possible damage to it.
Safety notes for battery If battery fluid leaks inside the camera, contact our customer service department. Do not heat the battery or throw it into a fire to avoid a possible explosion. If battery fluid leaks onto your skin, rinse your skin with clean water and seek immediate medical attention. Do not store the battery in a hot environment or in direct sunlight. Disposal of used batteries should be carried out in accordance with the local (national or regional) regulations.
Safety notes for memory card Do not drop the memory card or allow it to hit solid objects to avoid damaging it. Do not attempt to disassemble or repair the memory card. Do not expose the memory card to water. Always keep it dry. Do not remove the memory card when the camera is turned on. Otherwise, the memory card could be damaged. Do not directly edit the data on the memory card. Copy the data to your PC before you edit them.
Other Safety Notes Do not disconnect the power or turn the product off during the update process. Doing so may cause incorrect data to be written and the product may not power on later. Do not hang the neck strap of the camera around the neck of a child. When using your product on an airplane, observe the relevant rules specified by the airline. Due to the limitations of manufacturing technology, the LCD screen may have a few dead or bright pixels.
CONTENTS BEFORE YOU START.............. 1 SAFETY NOTES...................... 3 CONTENTS.............................. 7 GETTING READY...................11 MODE OVERVIEW................ 20 Display Setting.....................................20 LCD Screen Display.............................21 Overview of the screen icons in photo shooting mode.....................21 Overview of the Screen Icons in Movie Mode...................................23 Accessories Included...........................
Auto Scene Mode (ASCN).............33 Custom Settings...................................35 BASIC OPERATION............... 37 Viewing Photos and Videos.................48 Thumbnail View....................................49 Using the Zoom Function.....................37 Using Zoom Playback (for still pictures only)........................................50 Focus Setting.......................................38 Photos and Video Deletion...................51 Macro Mode...................................
Photo Shooting Setting Menu..............58 HDR...............................................67 Quality............................................58 Touch-up........................................68 AF-Assist Beam.............................59 Rotate............................................69 Digital Zoom...................................59 Resize............................................70 Date Imprint...................................59 i button playback function.....................
LCD Brightness..............................78 Battery Type...................................78 File Settings.........................................79 Format...........................................79 Copy to Card..................................80 File Numbering..............................80 Reset.............................................81 FW Version....................................81 Setting the USB Mode...................87 Connecting to your Printer.............
GETTING READY Accessories Included Your camera box should contain the camera model you purchased along with the following accessories. If anything is missing or appears to be damaged, please contact your retailer.
Install lens cap and neck strap 12
Part Names 1 . Zoom lever 4 56 78 9 10 2. Shutter button 3 3. Strap eyelet 3 2 1 4. Exposure compensation button 5. Continuous shot button 6. Power switch 11 7. AF assist beam/Self-timer lamp 12 9. Flash lamp 13 10. Flash button 8. Mode dial 1 1 . Microphone 12 . Speaker 13 .
1 4. i button 14 15 16 1 5. Indicator lamp 17 1 6. Fast video recording button 1 7. Menu button 18 1 8. Micro USB port 19 1 9. Micro HDMI port 20 21 22 23 20. AF button/Up button 2 1 . Flash button/Right button 22 . Delete button/Self-timer button/Down button 23 . Display button 24. Battery cover switch 30 29 28 27 26 25 24 25 . Battery cover 26. Playback button 27. Tripod socket 28. Macro button/Left button 29. SET button 30.
Installing Battery and Memory Card 1. Open the battery cover according to ①,②,③. 2.
3. Insert the memory card into the memory card slot as shown in the diagram below: Write protection buckle The memory card (SD/SDHC) is optional and not included in all camera packaging. If you have to purchase a memory card, select one with storage capacity between 4GB and 32GB to ensure correct data storage. To remove your memory card, open the battery cover, gently press the memory card to eject it and remove it carefully. 16 4. Close the battery cover according to ①,②.
Turn On / Off the Camera Set your Language, Date/Time Slide the power switch to turn on/off the camera. Set your Language, Date/Time after the first power-on Power Switch 1. When you turn the camera on for the first time, the language selection screen appears. 2. Press the arrow buttons to select your desired language. 3. After you press the button to confirm the selection, the Date/Time settings screen appears. 4.
Resetting your Language After you set your language for the first time, follow the instructions below to reset your language. 1. Turn the power switch to turn on the camera. 2. Press the button, press the up/down arrow button to select , and press the button to enter the menu. 3. Press the up/down arrow button to select , and press the button or right arrow button to enter the menu. 4. Press the up/down arrow button to select 「Language」and press the button or right arrow button to enter the menu. 5.
Resetting Date/Time After you set your Date/Time for the first time, follow the instructions below to reset date and time. 1. Turn the power switch to turn on the camera. 2. Press the button, press the up/down arrow button to select , and press the button to enter the menu. 3. Press the up/down arrow button to select , and press the button or right arrow button to enter the menu. 4. Press the up/down arrow button to select 「Date & Time」and press the button or right arrow button to enter the menu. 5.
MODE OVERVIEW Display Setting Press the button to display the settings: Classic, Full, Off. Classic: Displays the camera parameters on screen SD 1234 16M 00:56:00 F3.0 1/50 -0.3 EV 400 ISO Full: Camera parameters with Grid and Histogram SD 1234 16M 00:56:00 F3.0 20 1/50 -0.
LCD Screen Display Overview of the screen icons in photo shooting mode 3 2 1 4 x1.0 6 7 19 8 18 1234 17 16M 16 15 1/50 -0.3 EV 14 13 400 ISO 12 9 10 00:56:00 F3.
10 Video Quality 11 ISO Value (Adjustable in Self-timer 2 sec Self-timer 10 sec Mode) 12 Remaining Recording time Self-timer Smile 13 Exposure Compensation (EV value) (Adjustable in Mode) 14 Shutter Speed (Adjustable in Mode) 15 Histogram 16 Aperture Value (Adjustable in 17 Image stabilization 18 Focus Frame 19 Expo Metering AiAE Spot Center 20 AF Mode Force Off Flash Auto Mode) Force Flash Slow Sync. Slow Sync.
Overview of the Screen Icons in Movie Mode 1 2 3 5 4 7 Color Effect 8 Video Quality 9 Remaining Recording time 6 10 Exposure Compensation (EV value) 11 Image stabilization SD x1.0 12 Focus Frame 15 7 14 13 Eye-Fi ON (with signal) 14 Expo Metering 13 12 11 00:56:00 8 10 AiAE Spot -0.
Overview of the Screen Icons in Playback Mode 1 2 3 1/45 SD 13 4 5 12 11 10 6 x2 7 8 0000 00-00 00:00 9 24 1 DPOF File 8 Image Zone 2 File Protection 9 Shooting Date 3 Memory space (indicating the current number of photos and total number of photos) 10 Eye-Fi ON (with signal) 4 Memory Card/Built-in Memory 11 Red-Eye Reduction 5 Battery Status 12 HDR 6 Zoom Magnification Area 13 Date Folder 7 Image Zoom Ratios
Using the Mode Dial This camera provides a convenient mode dial that allows you to manually switch between different modes with ease. The available modes are listed below: Mode Name Shutter priority Aperture priority Description In this mode, the optimal conditions for taking pictures will be set based on the subject and environment. It is the most commonly used mode for taking pictures.
Auto Mode Auto Mode is the easiest mode to take photos. While operating in this mode, the camera automatically optimizes numerous camera settings to adjust your photos and videos for the best possible results. SD Follow these steps: 1. Turn the power switch to turn on the camera. 2. Turn the mode dial to . 3. Compose your picture in the LCD screen and press the Shutter button halfway down to focus on the subject. 4. The LCD screen will show a green focus frame when the subject is in focus. 5.
Program AE Shutter Priority When (Program AE) mode is selected, you can adjust the EV value and ISO value. 1. Turn the mode dial to and press the button to configure settings. When (Shutter Priority) is selected, you can adjust the shutter speed, ISO value and EV value. The camera automatically sets the aperture value based on the shutter speed value and ISO value to get the most appropriate exposure value. 1. Turn the mode dial to and press the button to configure settings. F3.0 1/50 -2.
Manual Mode Aperture Priority When selecting (Aperture Priority) mode, you can adjust the aperture size / EV value and ISO value. Selecting a large aperture opening will emphasize the point of focus and show a blurry background and foreground. A small aperture opening will keep both the background and main object in clear focus. 1. Turn the mode dial to and press the button to configure settings. When selecting manual ( ) mode, you can set the aperture / shutter speed manually and ISO value. 1.
Face Beautifier In Portrait Mode, the camera is set to automatically adjust camera exposure for realistic portrayal of skin tones. Beautifier Mode has 3 effects: • Effect 1: Skin Soften 1. Turn the mode dial to select Face Beautifier Mode ( ). • Effect 2: Skin Soften + Eye Brightening • Effect 3: Skin Soften + Eye Brightening + Eye Enlargement 2. Press the button and press the up/down button to select . 3.
Panorama Mode With Panorama Mode, you can take a series of pictures which will be stitched automatically into a ultra-wide panoramic picture by the camera. Follow the steps below: 1. Turn the mode dial to Panorama Mode ( ). 2. Press the arrow buttons to select a shooting direction. (The right direction is used as default if you do not make any choice) 2 seconds later, the camera is ready to take pictures. You can also press the button or half press the shutter button to be ready to take pictures. 3.
Scene Mode Flash Mode, Self-Timer, Macro Mode, and Exposure Compensation are all disabled in Panorama Mode. In the process of shooting in the panoramic mode, when the LCD screen shows “Improper alignment. Please try again.”, it means that in the process of camera moving, the moving angle is off the green line, shooting can't be done. You will have to try again. You can select an appropriate mode from the 12 scene modes according to the type of environment you are shooting.
Scene Rapidly identify pet (dog/cat), capture the dynamic moment of pet. Sunset For sunsets. Capture subjects in strong sunlight. Fireworks For fireworks at night. The use of a tripod is recommended. Sport For fast-moving subjects. Capture sharp, action shots with minimal blur. This mode is not recommended for shooting indoors. Night Portrait For portraits against night scenery. Landscape For landscapes and outdoor shots. Vivid reproduction of green and blue.
Auto Scene Mode (ASCN) In “ASCN” scene mode, the camera can detect different environments intelligently and automatically select the best scene and photo settings for you. “ASCN” can intelligently detect the following scenes: Icon Mode Name Landscape Mode Night Portrait 2. Hold the camera steadily and aim at the subject. The optimum scene mode will be selected automatically. Backlit Portrait 3. Press the shutter button half-way down to focus. Night Landscape Mode 4.
Mode Name Landscape Mode 34 Description For landscapes, will automatically adjust the exposure and reproduce vivid green and blue colors. Portrait Mode Most suitable for capturing people with focus on their faces. Night Portrait When you take portraits at night, or in low light conditions, ASCN will automatically adjust the exposure for people and night scenes.
Custom Settings The user can store the frequently used shooting modes and parameters and switch to this mode for quick adjustment. Settings under after reset): mode (unset state or state 1. Turn the mode dial to select the mode, and enter the setup screen, as shown in the figure below: Go to setting CS mode Yes Or Rotating the mode dial to skip . Select one capture mode to define CS . For setting under other modes (use this method to select a different custom setting): Landscape Save Exit 2.
5. Press the down arrow button select「Custom Settings」and press the button or the right arrow button to enter the menu. 7. Turn the mode dial to switch to the custom settings ( ). 8. The photo settings you stored the last time are invoked. When the mode is used for the first time, there is no preset parameter stored in the mode. 6. Select「Yes」to save or「No」to cancel. Under the mode, if you need to retain or modify the set parameters (except the parameters in ) in restart or all modes.
BASIC OPERATION Using the Zoom Function Your camera is equipped with two types of zoom functions: Optical Zoom and Digital Zoom. Toggle the Zoom Lever of the camera to zoom in or out of the subject while taking pictures. SD Zoom Indicator 1234 00:56:00 -0.3 EV 400 ISO Zoom Lever When the Optical Zoom reaches the threshold as Digital Zoom, release and turn the Zoom Lever to T to switch between the Optical zoom and Digital zoom.
Focus Setting In different photo shooting modes, you can select different focus methods. 1. Press the up arrow button ( ) to display the settings screen. Object Tracking Smart tracking of the object in motion under the focusing shooting. 3. Press the button to confirm the settings and exit the menu. Once enabled, Object Tracking will only work when lens is focused on the object. Single-AF 2.
Macro Mode The Macro Setting is ideal for shooting small objects or close-up photos. This mode allows you to focus on subjects very close to the camera. 1. Press the left arrow button ( ) to enter the Marco Menu. Macro Off 2. Press the left/right to select the following 2 modes: • Macro Off Select this option to disable Macro. • Macro On Select this option to make focusing on the object closer to the lens (At the W side, the shooting distance should be more than 1.6 cm). 3.
Self-Timer Setting Using this function can take photos at regular time. The camera can be set to shoot after 2 seconds, 10 seconds since pressing the shutter or shoot after smile. 1. Press the down arrow button ( enter the self-timer menu. • Self-timer 10 sec A single picture is shot 10 seconds after the Shutter Button is pressed. • Self-timer Smile Press the Shutter Button and a picture will be taken immediately after a smile is detected. ) to 3.
Flash Mode The flash is mainly for supplementing light for the scene. The flash is usually used in shooting against the light to highlight the object shot through lightening the object while darkening the background; it is also suitable for metering and shooting in darker scenes through exposure. 1. Press the Flash Button to pop up the flash. 2 2. Press the right arrow button ( the Flash Settings Menu. 1 • • • • ) to enter • • ਘ⥺斿Ұ Force Off ܠ昘旅 3.
White Balance Setting The white balance function allows adjustment of the color temperature for different light sources (Adjustable in Mode). • AWB • Daylight Follow the steps below to set white balance of the camera: • Cloudy • Fluorescent • Fluorescent CWF • Incandescent • Manual WB (Fully press the shutter button to detect the white balance value) • Color Temp. (1900K~10000K) Press direction buttons Up / Down to "Adjust the K value"; Press the direction button Left to exit the K value.
Continuous Shot Follow the steps below to configure the Continuous Shot Settings: 1. Press the Menu. to enter the Continuous Shot • 3 Shots • Time-Lapse Take pictures based on the preset interval (30sec/ 1min/ 5min/ 10min). 3. Press the button to confirm the settings and exit the menu. 4. Press the Shutter button to start continuous shooting. Single The flash is disabled in this mode in order to achieve quick succession of shots. 2.
EV Setting The EV function menu of the camera includes functions, such as EV adjustment, ISO, Shutter Adjustment, Aperture Adjustment, etc. Using the appropriate function settings can improve your pictures. To select the best setting for optimum photos, follow these steps: 1. Press the screen. Exposure Compensation Set up to adjust the picture brightness. In the case of a very high contrast between the photographed object and the background, the brightness of the picture can be appropriately adjusted.
ISO Shutter Adjustment The ISO function allows you to set the sensitivity of the camera's light sensor based on the brightness of the scene. To improve the camera's sensor performance in darker environments, a higher ISO value is required. A lower ISO value is needed when shooting in brighter conditions. For shutter speed, the camera may automatically set the aperture value corresponding to the manually set shutter speed so as to obtain a most suitable exposure value.
Using Quick Recording Aperture Adjustment You can adjust the aperture size value. Selecting a large aperture opening will emphasize the point of focus and show a blurry background and foreground. A small aperture opening will keep both the background and main object in clear focus. (Adjustable in Mode) In shooting mode, press the Recording shortcut button to begin recording video. After finishing, press the Recording short cut button or the Shutter Button to stop and store the video.
i Button Function Menu Mode: The Image Color Setting allows you to select different color effects. 1. Press the button to select the Image Color Setting Menu. 2. Press the left/right arrow button to select the Image Color Setting options.
PLAYBACK Viewing Photos and Videos To view photos and videos on LCD screen: 1. After pressing the screen. button, the last photo or video clip taken will be displayed on the LCD 2. Use the Left/Right navigation buttons to scroll through the photos or video clips stored in the internal memory or on the memory card. 3. To play a selected video clip, press the button to enter the Movie Playback Mode. An operation guide appears on the screen when playing back a video.
Thumbnail View When in Playback Mode, rotate the Zoom Lever counter clockwise to the position to display thumbnail images of the photos and videos on the screen. (the picture is displayed in horizontal position) W Zoom Out T Zoom In 2. Press the arrow buttons to select a picture or video clip to view and press the button to restore it to the original size. If the indicator appears on the LCD, then a movie file is currently being displayed. 1.
Using Zoom Playback (for still pictures only) When playing back photos, you can also use the Zoom Slider to zoom in on the photos 2 to 8 times. 1. Press the button to switch to Playback Mode. 2. Press the left/right button to select a picture to be zoomed in. 3. Rotate the Zoom Lever clockwise to ( ) to zoom in. 4. The bottom right corner of the screen will display the number of times and area of the photo zooming operation. x2 5.
Photos and Video Deletion In playback mode, press the down arrow button to delete your photos and videos. To delete photos or videos: 1. Press the button to switch to playback mode. 2. Press the left/right arrow button to select the photos and videos to be deleted. 3. Press the down arrow button and the deletion screen is displayed. 4. Press the up/down arrow button to select 「Delete One」or「Exit」and press the confirm. button to Erased photos/video clips cannot be recovered.
Slideshow You can use this setting to view the pictures taken by the method of slide playing. 1. Press button to enter playback screen. 2. Press button to enter the slide option (except for video file). 3. Press the left/right button to select slideshow playing or 「Cancel」 to return to the playback screen. 52 4. Press the button to confirm the setting. Pictures rotate automatically during a slide show. Slide playing function supports movie playing.
USING THE MENUS Photo Setup Menu Mode: 1. In Photo Shooting Mode, press the button to enter the Photo Shooting Menu. Expo Metering (Exposure Metering) Use this setting to select the "target" size of the camera's field of view to be metered. 2. Press the up/down arrow button to select the Photo Shooting Menu to be set. 3. Press the left/right arrow button to select the Photo Shooting Menu to be set and press the button to confirm. Refer to the following pages for more details about each setting.
Image Size OIS The size setting refers to the image resolution in pixels. A higher image resolution allows you to print that image in larger sizes without degrading the image quality. This mode can help reduce photo blur caused by unintentional hand shake, or low light. The bigger the number of recorded pixels is, the better the image quality becomes. As the number of recorded pixels lessen, you will be able to record more images on a memory card.
Cont. AF HDR Enable the continuous AF to be able to continuously focus automatically when taking pictures. Use this setting to control wide dynamic image range when taking static pictures. Photos with extreme contrast of bright and dark areas will still maintain distinguishable detail and depth.
Face Beautifier Scene Set the effect of the Face Beautifier mode. Select the scene mode under the SCN mode.
• Shooting menu in the shooting mode (Ο: Optional Х: Not optional) Shooting Modes Options 16M Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Х Х Х Х Х Х Ο 57
Photo Shooting Setting Menu Mode: 1. Press the button in Photo Shooting Mode and press the up/down button to select . 5. Press the up/down arrow buttons to select an option and press the button to confirm. Quality The Quality Setting can be used to adjust the image compression ratio. 2. Press the button to enter the menu. 3. Press up/down arrow button to select , and press the button or right arrow button to enter the menu. 4.
AF-Assist Beam Date Imprint In a darker environment, AF Assist Beam can be turned on for better focus. Include a Date/Time stamp on the photo image. Digital Zoom Turn on or off the digital zoom.
Quick Review Custom Settings This option allows quick review of the photos immediately after they are taken. Each photo is displayed on the LCD screen based on the selected time. Custom Settings stores the current photo shooting mode and its parameters. The stored mode and parameters are directly invoked in Custom Settings mode.
Face Detection For detecting and focusing on faces to make all faces as clear as possible in photo mode.
Movie Menu Mode: Expo Metering (Exposure Metering) 1. Turn the mode dial, select the mode and press the button to enter the Movie Menu. Use this setting to select the "target" size of the camera's field of view to be metered. 2. Press the up/down arrow button to select the Movie Menu to be set. Expo Metering: AiAE 3. Press the left/right arrow button to select the Movie Menu to be set and press the button to confirm.
* The longest recording time is 29 AIAE (Artificial Intelligence AE): Automatically selects the central and peripheral metering, to calculate the reasonable value of metering by weighting. minutes at one time. When recording in higher pixel resolutions for extended periods of time, this can cause the camera to generate heat. This is not a camera malfunction. Video Quality Set the image resolution used during video recording.
Movie Setting Menu Mode: 1. Turn the mode dial and select the video recording screen. to enter 2. Press the button, press the up/down arrow button to select , and press the button to enter the menu. Press SET To Enter Menu 3. Press up/down arrow button to select , and press the button or right arrow button to enter the menu. 64 4. Select the items to be set and press the button or the right arrow button to enter the menu. 5.
Digital Zoom Custom Settings Turn on or off the digital zoom. Custom Settings stores the current movie shooting mode and its parameters. The stored mode and parameters are directly invoked in Custom Settings mode.
Playback Menu Mode: 1. Press the button to display the playback screen and press button to enter the menu. 2. Press the up/down arrow button to select the playback to be set and press 3. Press the left/right arrow buttons to select an option and press the Photo Video Press SET To Confirm Press SET To Confirm Normal Mode Normal Mode Refer to the following pages for more details about each setting. 66 button to enter. button to confirm.
Playback HDR 1. Press the button, select the settings, and press the button to display the settings screen. With the HDR function, pictures that are overexposed may be corrected to optimize the highlights and lowlights captured to more accurately represent the actual scene. 2. Press the left/right button to select from the following 2 functions: Normal Mode: Display all images. Date Mode: Arranged by date. 1. In Playback Mode, press the left /right arrow button to select the photos to be edited. 2.
Touch-up 1. In Playback Mode, press the left /right arrow button to select the photos to be edited. 2. Press the button, select the settings, and press the button to display the settings screen. : HDR 3. Press the left/right button to select Touchup options or「Cancel」to return to the playback Screen. : Cancel 4. After using the HDR function, the image will be saved as a new file and the original file is still stored in the memory.
Rotate 4. Press the button to confirm the setting. The Touch-up mentioned here is the individual beautification for three effects, beauty mode allows you to select from single, two, or all three effects combined. You can use this setting to change the orientation of the picture. 1. In Playback Mode, press the left /right arrow button to select the photos to be edited. 2. Press the button, select the settings, and press the button to display the settings screen. 3.
Resize 4. Press the button to confirm the setting. Videos and panoramic pictures cannot be rotated. The rotated picture file will replace the original photo. This setting allows you to resize a picture to a particular resolution and saves it as a new picture. 1. In Playback Mode, press the left/right arrow button to select the photos to be edited. 2. Press the button, select the settings and press the button to display the settings screen. 3.
i button playback function This setting allows you to change the picture color effect. The file is saved as a new photo and stored in memory together with the original photo. 1. In Playback Mode, press the left/right arrow button to select the photos to be edited. 2. Press the button to select the Image Color Setting Menu. 3. Press the left/right button to select the corresponding menu or「Cancel」to return to the playback Screen.
Playback Setting Menu Mode: 1. Press the button to show the playback screen, press the button, and press the up/down button to select . 5. Press the up/down arrow buttons to select an option and press the button to confirm. 2. Press the Refer to the following pages for more details about each setting. button to enter the menu. 3. Press up/down arrow button to select , and press the button or right arrow button to enter the menu. 4.
Protect To prevent any pictures or videos from being accidentally erased, use this setting to lock one or all of the files. There are 4 sub menus available: • One Lock the selected photo or video if they are unprotected; unlock the selected photo or video if they are protected. • Date Folder Protect all photos in the Date Folder. • All Lock all photos or videos. • Reset Cancel all locked photos or videos. To lock or unlock the photo and video files: 1.
Delete You can delete one or all photo/video files. There are 3 sub menus available: • One Delete one photo or video. • Date Folder Delete all photos in the Date Folder. • All Delete all photos or videos. 3. Press the up/down arrow buttons to select an option and press the button to confirm. To delete photo or video files: 1. Press the up/down arrow button to select 「Delete」and press the button or right arrow button to enter the submenu. 2.
DPOF (Digital Print Order Format) Trim The DPOF feature allows you to compile and select a group of pictures that you would like to print and will save your selection on the memory card so that you can use the memory card to print without having to individually specify the photos you want to print. The Trim Setting allows you to crop photos and save them as new pictures. The printer that supports DPOF is needed for printing. 1.
Setup Menu Mode : 1. Press the button in any mode and press the up/down button to select . 2. Press the button to enter the menu. 3. Press up/down arrow button to select , and press the button or right arrow button to enter the menu. Refer to the following pages for more details about each setting. Sound Settings To change this setting: 1. Select「Sound Settings」in the basic settings menu. Press the button or right arrow button to enter the menu. 2. Press the left/right arrow button to select an option.
Power Saver Language This setting allows you to save power and get the maximum possible running time for your camera's batteries. Follow the steps below to turn the LCD screen and camera off automatically after a consecutive period of inactivity. 1. Select「Power Saver」in the basic settings menu. Press the button or right arrow button to enter the menu. 2. Press the up/down arrow button to select an option. Refer to the “Reset your language” section on page 18.
Date/Time Battery Type Refer to the “Reset Date/Time” section on page 19. Please choose the right type of battery before using. LCD Brightness 1. Select「BATTERY TYPE」in the basic settings menu. Press the button or right arrow button to enter the menu. Use this setting to adjust the brightness of your LCD screen. 1. Select「LCD Brightness」in the basic settings menu. Press the button or right arrow button to enter the menu. 2. Press the up/down arrow button to select an option. ALKALINE Normal 2.
File Settings Format Please note: formatting enables you to delete all contents in the memory card and built-in memory, including protected photo and movie files. To use this setting: 1. Press the button, press the up/down arrow button to select and press the button to enter the menu. 2. Press up/down arrow button to select and press the button or right arrow button to enter the menu. 3. Press the up/down arrow button to select「Format」and press the button or right arrow button to enter the menu. 4.
Copy to Card File Numbering Use this setting to copy the files stored in the internal memory to an memory card. 1. Press the button, press the up/down arrow button to select and press the button to enter the menu. 2. Press up/down arrow button to select and press the button or right arrow button to enter the menu. After you take a picture or video clip, the camera will save it with a sequential number. You can use this to reset the file numbering to 0001. 1.
Reset FW Version Use this setting to restore the camera to its original default settings. Use this setting to view the current camera firmware version. 1. Press the button, press the up/down arrow button to select and press the button to enter the menu. 1. Press the button, press the up/down arrow button to select and press the button to enter the menu. 2. Press up/down arrow button to select and press the button or right arrow button to enter the menu. 2.
CONNECTIONS Connecting to a Computer You can use a micro USB cable to connect the camera and copy (transmit) photos to a computer, printer or other device. Setting the USB Mode The camera’s USB port can be set to connect with either a computer or a printer. The following steps will allow you to ensure that the camera is correctly configured to connect with a PC. 1. Press the button, press the up/down arrow button to select and press the button to enter the menu. 2.
Transferring files to your computer The computer will automatically detect the camera as a removable drive. Double-click the My Computer icon on the desktop to locate the removable drive and to copy folders and files in the drive to a directory on your PC as you would copy any typical folder or file. Follow the steps below to connect the camera to a computer. 1. Make sure the computer is turned on. 2. Connect one end of the supplied micro USB cable to the USB/AV OUT port on your camera. 3.
Video System You can use the AV cable (which should be purchased separately) to connect the camera and the television for realizing the video output. Connect one end of the AV cable to AV port of the camera, connect the other end to AV-OUT port of the television. Adjust the format of the video output system according to your requirements, and the steps are as follows: 1. Press the button, press the up/down arrow button to select and press the button to enter the menu. 2.
Set Eye-Fi Card Connection Mode This camera supports the wireless connection for Eye-Fi card, Enable Eye-Fi connection by following below steps. 1. Press the button, press the up/down arrow button to select and press the button to enter the menu. 2. Press up/down arrow button to select and press the button or right arrow button to enter the menu. 3. Press the up/down arrow button to select 「Eye-Fi」and press the button or right arrow button to enter the menu.
Supported HDMI Connections HDMI (High Definition Multimedia Interface), is a fully digital audio/video transmission interface, through which uncompressed audio and video signals are transmitted. Direct transmission of digital video signals to your TV reduces conversion loss and improves image quality. Connecting HDMI-Ready TV 1. Use the cable with high resolution output terminal (which should be purchased separately) to connect the camera to the television which meets HDMI standard. 2.
Connecting to a PictBridge Compatible Printer PictBridge technology allows printing of the photos saved in the memory card by the printer. 3. Press the up/down arrow button to select「USB」and press the button or right arrow button to enter the menu. To find out if a printer is PictBridge compatible, simply look for the PictBridge logo on the packaging or check the owner's manual for specifications.
Connecting to your Printer 1. Make sure the printer is turned on. 2. Connect one end of the supplied micro USB cable to the USB port on your camera. If the camera is not connected to a PictBridge compatible printer, the following error message will appear on the LCD screen. 3. Connect the other end of the micro USB cable to the USB port on the printer.
Using the PictBridge Menu After setting the USB mode to Printer, the PictBridge Menu will appear. Print (with Date) If you have set the date and time on your camera, the date and time will be recorded and saved with each photo you take. 1. In the PictBridge menu, select「Print (with Date)」and the screen as shown below appears. Press the up/down arrow button to select a menu item and press the button or right arrow button to enter the item.
Print (without Date) 3. Press the up/down arrow button to select the number of copies for the currently displayed photo. 4. Press the button and the following screen will appear. 5. Select「Yes」and press the button to confirm; select「Cancel」to cancel printing. Use this setting to print the photos without dates on them. 1. In the PictBridge menu, select「Print (without Date)」and the screen as shown below appears. 2. Press the left/right arrow button to select a photo to be printed. 3.
Print Index You can print all photos in the camera via this function. 1. In the PictBridge menu, select「Print Index」and the screen as shown below appears. 5. Select「Yes」and press the button to confirm; select「Cancel」to cancel printing. 2. Select「Yes」and press the button to confirm; select「Cancel」to cancel printing.
Print DPOF Images Exit To use DPOF printing, you must select your photos for printing using the DPOF settings beforehand. See “DPOF” section on page 75. Select「Exit」to exit the PictBridge menu. At this time, the message「Remove USB Cable!」 appears on the screen. 1. In the PictBridge menu, select「Print DPOF Images」and the screen as shown below appears. Disconnect the micro USB cable from the camera and printer. 2. Select「Yes」and press the button to confirm; select「Cancel」to cancel printing.
APPENDICES Specifications Design and specifications are subject to change without notice. Effective Image Sensor Pixels 16.15 Mega pixels Total Image Sensor Pixels 16.44 Mega pixels [1/2.3"CCD] Lens Focal Length 4.3mm (Wide) - 154.8mm (Tele) 35mm film equivalent 24mm (Wide) - 864mm (Tele) F number F3.0 (Wide) - F6.6 (Tele) Lens Construction 11 groups 15 elements Optical Zoom 36x Focusing Range Normal: (Wide) 50cm ~ ∞, (Tele) 200cm ~ ∞; Macro: 1.
Number of Recording Pixels Still Image Movie (3:2) (16:9) 16MP: 4608×3456 10MP: 3648×2736 5MP: 2592×1944 3MP: 2048×1536 0.3MP: 640×480 14MP: 4608×3072 12MP: 4608×2592 2MP: 1920×1080 1280×720 (30fps), 1280×720 (15fps), 640×480 (30fps) Image Compression Best, Fine, Normal DCF, DPOF (Ver1.1) Support Yes File Format 94 (4:3) Still Image Exif 2.3 (JPEG) Movie MOV [Image: H.
HDR Yes Video Panorama Up to 180°(Horizontal) LCD Display 3.
Flash Flash Method Pop-up (Manual) Flash Modes Force Off, Flash Auto, Force Flash, Slow Sync., Slow Sync. + Red-Eye, Red-Eye Reduction Shooting Capability (Battery Performance) Operation Environment Dimensions (W×H×D) (Wide) Approx. 0.5m ~ 7.5m (ISO 800) (Tele) Approx. 1.2m ~ 3.7m (ISO 800) Internal Memory: Approx.
Prompts and Warning Messages Message Description Action Warning! Battery exhausted. The camera battery is used up. It is a warning indicating that the camera is going to shut down. Charge the battery. Lens obstruction, Re-start Camera. The lens is jammed or some foreign object is preventing the lens from functioning properly. Turn off the camera and restart it to reset the lens. Built-in memory error! An error occurs in internal memory. Format the internal memory. Improper alignment.
Message 98 Description Action Remove USB Cable! Indicates that you can disconnect the USB cable. The message disappears after you disconnect the USB cable. Connection Failed! Failure to connect to your PC, printer, TV (with HDMI). Remove USB cable and retry connection Write Protect ! The memory card is locked. Unlock the write-protect switch of the memory card. Card Full ! Indicates that the memory card is full. Insert a new SD memory card or delete unwanted images.
Message Description Action Card is not formatted. When an error occurs in the memory card, the message "Not Formatted" appears. The message will disappear after 2 seconds. Format the SD memory card with this camera. Slow access When a memory card lower than Class 4 is used to record a HD movie, the writing speed will be slower and recording will not continue. Use an SD memory card with Class 4 or higher. No Red-Eye Detected! Red eyes have not been detected in the image.
Message 100 Description Action Too many pictures for quick processing. During the playback by date, the images exceed specifications so that it is not possible to play by date. This may be solved by deleting unnecessary images. Unable to recognize files. The format of the file to be viewed is not supported or the file is corrupted so it cannot be properly read. You may be able to play it back on another brand of camera or on your computer.
Troubleshooting Problem Camera does not turn on Camera turns off suddenly during operation The picture is blurred Images and video files cannot be saved Images will not print from the connected printer Possible causes The battery has been depleted. The battery is not inserted correctly. The batteries have been depleted. Solution Recharge the battery. Camera shakes while taking a picture. Turn on OIS feature. Please use tripod for high magnification (above 15X) optical zoom.
Problem 102 Possible Causes Solution Saving data to memory card is slow Using a memory card below Class 4 may result in slower recording times. Use an memory card with write Class higher than 4 to improve performance. Cannot write to the memory card The memory card has been locked. Too many movies to process The number of pictures or folders in the memory card exceed the specifications, so the playback of data folder can not be displayed.
Licensed Product The Kodak trademark and trade dress are used under license from Kodak. © 2014 by JK Imaging Ltd. All rights reserved. JK Imaging Ltd. 1411 W. 190th Street, Suite 550, Gardena, CA 90248, USA JK Imaging Europe, 71 Clarendon road, Watford, WD17 1DS, UK www.kodakpixpro.com Ver.