Start Here 3200 Series All-in-One Printer Back Ho me MS SD/H C MM C Print Copy Scan Includes Information on the: ESP 3250 All-in-One Printer ESP 3260 All-in-One Printer Note: A USB 2.0 cable is required to connect your KODAK All-in-One Printer to your WINDOWS or MACINTOSH OS Computer. Available in the KODAK Store or see your local retailer.
1 Unpacking the Printer Included with your KODAK All-in-One Printer: Inkjet Printer Software FOR WINDOWS & MACINTOSH Power Cord and Adapter Printhead Black & Color Ink Cartridges Software CD IMPORTANT: To view a setup video for your printer, go to www.kodak.com/go/inkjetvideo. Back Home MS SD/HC MMC a. Remove all shipping tape from the outside of the printer. Printer Access Door Scanner Lid MS SD/HC b. Lift the printer access door. MMC c.
2 Connecting the Power a. Connect the: • power cord to the adapter • adapter to the printer • power cord to the power source USB Do not connect the USB cable to the printer until instructed during software install. b. Remove the plastic film from the LCD. Back Hom e MS SD/ HC MM C Back Home MS c. Press ON . SD/HC MMC d. Select your language and press OK. www.kodak.
3 Inserting the Printhead MS SD/HC MMC a. Lift the printer access door. b. Carefully remove the printhead from its bag. Do not touch the copper-colored contacts. c. Remove the two plastic protective shields. Carriage d. Place the printhead into the carriage. Insert at the angle shown. e. Push firmly against the target label of the printhead until you hear a loud snap. 4 www.kodak.
4 Inserting the Ink Cartridge a. Remove the black ink cartridge from its bag. b. Carefully remove and discard the orange cap. Handle ink cartridges carefully to avoid ink transfer. c. Insert the black ink cartridge into the printhead. d. Press down on the ink cartridge until you hear it click into position. e. Repeat steps 4a - 4d with the color ink cartridge. Back Home MS f. Close the printer access door and press OK. SD/HC MMC www.kodak.
5 Loading Paper and Calibrating a. Open the paper tray. Back Home MS SD/HC MMC Paper Tray Left Paper-edge Guide b. Pull out the paper tray extender until it is fully extended. Paper Stop c. Lift the paper stop. Back Home MS d. Make sure the left paper-edge guide is to the far left. SD/HC MMC Paper Tray Extender e. Carefully fan and stack the paper, then insert it into the tray. Back Home MS f. Move the paper forward until it stops. SD/HC MMC g. Move the left paper-edge guide until it stops.
6 Installing Software on WINDOWS OS a. Load the KODAK All-in-One Printer Software CD into the CD drive. Follow the on-screen instructions. FO RW IND OW S& CIN MA TO SH If the installer window does not open, click Start, then click Computer or My Computer, and double-click the CD drive. NOTE: If your computer does not have a CD drive, go to www.kodak.com/go/downloads to download the software. b. Connect the USB cable to the USB port on the printer and to your computer.
7 Installing Software on MACINTOSH OS a. Connect the USB cable to the USB port on the printer and to your MACINTOSH Computer. b. Load the KODAK All-in-One Printer Software CD into the CD drive. Follow the on-screen instructions. If the installer window does not open, double-click the KODAK All-in-One Printer Software CD icon on the desktop. FOR WINDOWS & MACINTOSH KODAK Home Center Software for MACINTOSH OS KODAK Home Center is installed with your KODAK All-in-One Printer Software.
Warranty Information Limited Warranty Kodak warrants Kodak consumer electronic products and accessories (“Products”), excluding batteries, to be free from malfunctions and defects in both materials and workmanship for one year from the date of purchase. Retain the original dated sales receipt. Proof of the date of purchase will be required with any request for warranty repair. Limited Warranty Coverage Warranty service is only available from within the country where the Products were originally purchased.
Safety Information • Read and follow these instructions before using KODAK Products. • Always follow basic safety procedures. • Follow all warnings and instructions marked on the equipment. Warning Statements • Do not expose this product to liquid, moisture, or extreme temperatures. KODAK AC Adapters are intended for indoor use only. The use of controls, adjustments, or procedures other than those specified herein may result in exposure to shock and/or electrical or mechanical hazards.
Registration has its rewards—including a terrific offer. Register your KODAK All-in-One Printer and get great support, expert tips, free software downloads—plus a phenomenal deal on inkjet supplies to get you started. Simply register right away when prompted during software installation or on the Web at www.kodak.com/go/register. Registration takes a minute—but the rewards are lasting. Inkjet supplies offer valid for U.S. residents only. www.kodak.
Thank you for purchasing a KODAK All-in-One Printer. In the unlikely event that your printer does not operate as expected, please do not return it to the store. Do the following steps to begin troubleshooting. 1. Power cycle the printer by unplugging the printer. Wait five seconds, and then plug the power cord back into the printer. 2. Confirm that you are using a USB 2.0 cable. You can purchase a USB 2.0 cable online at www.kodak.com/go/usbcable or at your local retailer. 3.
