prosilica USER MANUAL November 1, 2006 GE1900 GE1900C Prosilica Inc. www.prosilica.com tel: 604.875.8855 fax: 604.875.8856 © 2006 Prosilica Inc. All rights reserved.
GE1900 User Manual 70-0028A-A Table of Contents Introduction......................................................................................................................................1 Precautions.......................................................................................................................................1 Warranty ..........................................................................................................................................1 Specifications...
GE1900 User Manual 70-0028A-A Introduction The GE1900 series of cameras are sensitive, 30 frames per second, HDTV format, Gigabit Ethernet cameras based on the Kodak KAI-2093M CCD sensor. Precautions READ INSTALLATION GUIDE CAREFULLY. This document contains specific information which is necessary for the correct operation and treatment of this product. DO NOT OPEN THE CAMERA. WARRANTY IS VOID IF CAMERA IS OPENED. This camera contains sensitive components which can be damaged if handled incorrectly.
GE1900 User Manual 70-0028A-A Specifications Sensor Type Kodak KAI-2093M (KAI-2093CM for color) Sensor Shutter Type Progressive Interline Image Resolution 1920 x 1080 pixels Pixel Size 7.4µm x 7.4µm Optical Format 1 inch Lens Mount Color Sensor Filter Pattern C-mount with adjustable back focus † Bayer Full Resolution Frame Rate 30.6 fps Frame Rate (640 x 480 ROI) 50 fps I/O 1 isolated TTL compatible input, 3 isolated TTL compatible outputs Power Requirements Less than 5.
GE1900 User Manual 70-0028A-A Supported Features Imaging Modes free-running, external trigger, fixed rate, software trigger Fixed Rate Control 0.
GE1900 User Manual 70-0028A-A Mechanical M3 3 MM DEEP 6 PLCS TYP 13.9* 26 26 80.4* 57 64 All dimensions are in mm. *Add 0.3mm for color cameras due to addition of IR blocking filter. 51.3 39.1 Figure 1. GE SERIES mechanical dimensions. Prosilica Inc.
GE1900 User Manual 70-0028A-A Connections 5 6 1 2 7 3 4 Figure 2. GE SERIES connection diagram. Prosilica Inc.
GE1900 User Manual 70-0028A-A Item 1: GIGABIT ETHERNET PORT This port conforms to the IEEE 802.3 1000BASE-T standard for Gigabit Ethernet over copper. It is recommended that CAT5E or CAT6 compatible cabling and connectors be used for best performance. Cable lengths up to 100m are supported. Item 2: General Purpose I/O PORT 9 8 10 12 7 1 11 2 3 6 5 4 Figure 3. General Purpose I/O Pin out. Camera rear view.
GE1900 User Manual 70-0028A-A Sync Out 2 and Sync Out 3 These signals only function as outputs and can be configured as follows: Exposing Corresponds to when camera is integrating light. Trigger Ready Indicates when the camera will accept a trigger signal. Trigger Input A relay of the trigger input signal used to “daisy chain” the trigger signal for multiple cameras. Readout Valid when camera is reading out data. Strobe Programmable pulse based on one of the above events.
GE1900 User Manual 70-0028A-A Item 4: Mini-SMB Sync Out 1 This Mini-SMB port on the camera uses an Amphenol 903-406J-51R connector. A suitable mating cable connector is Amp 413985-3 which can be used with RG174 coaxial cable. Contact Prosilica to purchase cabling. This connector is particularly useful for triggering multiple cameras in a “daisy chain” fashion. The Sync Out 1 signal can be configured as follows: Exposing Corresponds to when camera is integrating light.
GE1900 User Manual 70-0028A-A Item 7: AUXILIARY POWER PORT This port is required to provide power to the camera. This port provides threaded captivation of the power cable if required. The captivated cable mating connector is the Switchcraft 760K. This connector can be purchased from Prosilica or from http://www.digikey.com. This port can accept from 5V to 17V DC with the inner conductor being positive power and the external conductor being ground.
GE1900 User Manual 70-0028A-A Cleaning the Sensor DO NOT CONTACT CLEAN SENSOR UNLESS ABSOLUTELY NECESSARY. Identifying Debris Debris on the image sensor or optical components will appear as a darkened area or smudge on the image that does not move as the camera is moved. Do not confuse this with a pixel defect which will appear as a distinct point. Locating Debris Before attempting to clean the image sensor, it is important to first determine that the problem is due to debris on the sensor window.
GE1900 User Manual 70-0028A-A Adjusting the C-mount LOCKING RING C MOUNT RING Figure 4. Camera Front View. THE C-MOUNT IS ADJUSTED AT THE FACTORY AND SHOULD NOT REQUIRE ADJUSTING. If for some reason, the C-mount requires adjustment, use the following method. Loosen Locking Ring Use an adjustable wrench to loosen locking ring. Be careful not to scratch the camera. When the locking ring is loose, unthread the ring a few turns from the camera face.
GE1900 User Manual 70-0028A-A Camera Installation Computer Interface The Prosilica GE Series cameras will work with any Gigabit Ethernet network card; however Prosilica strongly recommends using Gigabit Ethernet components that support Jumbo Frames. A Jumbo Frame is loosely defined as a frame size greater than 1500 bytes however typical Jumbo Frames are around 9000 bytes.
GE1900 User Manual 70-0028A-A Gigabit Ethernet Setup for Windows o Install network card in computer. o Boot the PC and cancel the “Found new Hardware Wizard” window that may appear when Windows detects the new card. o Install the driver that came with the network card. o Once the driver is installed, open the Network Connections Dialog as follows: From the Windows desktop select start, then select Control Panel, then double click on the Network Connections icon.
GE1900 User Manual 70-0028A-A o Select the Internet Protocol (TCP/IP) check box and then select Properties. See Figure 6. Network card TCP/IP address.. Select the Use the following IP address and enter an IP address of 169. 254. x. y, where x and y can be any number. Press the TAB key after entering the IP address and the subnet mask will automatically be entered. The subnet mask is 255. 255. 0. 0. Click OK to save changes.
GE1900 User Manual 70-0028A-A Figure 7. Turn off Firewall. o Return to the Gige Local Properties window as in Figure 5. Select the Advanced tab as in Figure 7 and disable the Firewall for this device. Click OK to save changes. Gigabit Ethernet Cabling All Gigabit Ethernet cabling and connectors should be CAT5E or CAT6 compatible. Cable lengths must not exceed 100 meters. Power Connection The camera requires a 12V DC power supply that can source a minimum of 500 mA of current.
GE1900 User Manual 70-0028A-A Installing GigE Viewer for Testing o The latest Viewer software can be downloaded from http://www.prosilica.com/support.htm. o Run the GigE Viewer Installer.exe. This will install the Prosilica Digital Camera drivers as well as the Prosilica GigE Viewer application program. o Plug in the Prosilica camera via the Gigabit Ethernet port. Plug in the power connection. Verify that the Status LED 1 is a solid green. Run the Prosilica GigE Viewer Application.
GE1900 User Manual 70-0028A-A System Optimization o Open the Network Connections Dialog as follows: From the Windows desktop select start, then select Control Panel, then double click on the Network Connections icon. Double click the relevant network card listed or right-click the relevant network card and select Properties. This will open the properties window for your network card. See Figure 9. Figure 9. Network card main properties window.
GE1900 User Manual 70-0028A-A Figure 10. Network card advanced settings. o Set Maximum Frame Size or Jumbo Frames to the maximum possible value. A typical value is 9000. If the list contains a property called Receive Descriptors, then change this value to its maximum value. Select OK to save properties. o From the main properties dialog as in Figure 9, make sure that only the Internet Protocol (TCP/IP) check box is selected then click OK. The card is now optimized for use with the Prosilica camera.
GE1900 User Manual 70-0028A-A Trouble Shooting Check the Basics o Is power available? Check the status LED 1. If the LED is off, the camera is not getting power. Verify the connections and cabling. o Is the LED orange? This occurs if the firmware is corrupt because a firmware update was interrupted. If the LED is orange, run the firmware updater again, carefully following the instructions. If the problem persists, contact Prosilica. o Is the LED flashing orange? This indicates a fault with the camera.
