User Manual
CONTENTS CONTENTS......................................................... 1 BEFORE YOU START......................................... 3 FCC Warning............................................................................3 For Customers in Europe..........................................................4 About this Manual.....................................................................5 SAFETY PRECAUTIONS.................................... 6 GETTING READY............................................
Turning off the projector......................................................... 12 Resetting the projector........................................................... 12 Setup iShow (wireless projector) app for projection ..........................................................13 For iOS system...................................................................... 13 For Android system................................................................ 14 For Windows system..................................
1 BEFORE YOU START FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
For Customers in Europe This symbol [crossed-out wheel bin WEEE Annex IV] indicates separate collection of electrical waste and electronic equipment in the European countries. Please do not throw the equipment into domestic refuse. Please use the return and collection systems available in your country for proper, safe disposal of this product. “CE” mark indicates that this product complies with the European requirements for safety, health, environment, and customer protection.
About this Manual Thank you for purchasing this KODAK iShow 1000 Pico Projector. Please read this manual carefully and keep it in a safe place for future reference. Windows is registered in the United States and other countries by Microsoft Corporation, and its trademark use rights are reserved by Microsoft Corporation. Product names and trademarks involved in the Manual are for illustrative and identification purposes only.
2 SAFETY PRECAUTIONS When using a pico projector, please note the following safety precautions to prevent damage to the product. Do not dispose of improperly or expose to extreme heat. Do not operate the pico projector in moist or wet environments. Exposure to water may cause electrical shock or other injury. Avoid exposure to extreme temperatures as this may damage the pico projector. Do not operate the pico projector if damaged. Disassembling the pico projector will void the warranty.
3 GETTING READY Accessories Included Your KODAK iShow 1000 Pico Projector box should contain the pico projector you purchased along with the following accessories. If anything is missing or appears to be damaged, please contact your retailer.
Part Names Focus slider Speaker Power button Status indicator Earphone jack HDMI port Power inlet Tripod receptacle Support Lens 8 Reset hole
Charging Battery 1. Ensure the projector is turned off and connect it to the power charger. 2. Insert the plug of the power charger into the wall outlet to charge the battery. 3. Charging indicator: Red: Charging Green: Charging complete 4. To have maximum battery life, charge the battery for at least 4 hours the first time.
Downloading and installing iShow (wireless projector) app 1. For iOS system users: Please search for the iShow (wireless projector) app in the App Store ® , download the app, and install it on your device. 2. For Android system users: Please search for the iShow (wireless projector) app in Google Play ® , download the app, and install it on your device. 3.
4 Basic Operations of the Projector Turning on the projector 1. Press and hold the power button for three seconds to power up the projector. The button can be released when the status indicator lights up. 2. The projector will display the start up screen. Pico Projector Setting up the projector using the support 1. Open the support. 2. Place the projector on a stable surface.
Adjusting focus 1. Move the focus slider to adjust the clarity of the projected image. 2. Stop moving the slider once the projected image becomes clear. Turning off the projector 1. Before turning off the projector, close any files that are being displayed. 2. Press and hold the power button for three seconds to turn off the projector.
5 Setup iShow (wireless projector) app for projection For iOS system Due to incompatibility on some operating systems, the formatting of some documents may not be preserved. We recommend the use of PDF files to minimize formatting inconsistencies. Your device can only wirelessly connect to one signal at a time.
8. When the pico projector starts, your device’s wireless network will automatically detect the signal “iShow-XXXX” (the signal name is the same as the SSID name, which can be set by the user). Select this signal and your device will connect to the projector. 9. Click on the installed iShow (wireless projector) app on your device and the file selection pane will appear as shown below. 10.
3. To sync your documents, use your device’s data cable to connect your device to the computer. Move the documents that you want to project from your computer onto your device. If you prefer to wirelessly transfer files to your device via email or other means, remember to download and save them onto your device. Once they are saved to the device, the iShow (wireless projector) app will automatically locate them. 4. Once you have completed adding files, you may disconnect the device from the computer. 5.
9. Once the file type is selected, the appropriate files will appear. Tap the file that you want to project. Once you have finished displaying this file, return to the file selection pane to choose your next file. For Windows system 1. Use enclosed CD-ROM to install iShow (wireless projector) app on your computer. 2. Power on your KODAK iShow 1000 Pico Projector by pressing the power button for 3 seconds. 3.
6. Click the setting button again to return to the previous interface. Select the file type you want to project by clicking the appropriate icon (Documents, Pictures, or Video Files) at the top of the file selection pane. 7. Once the file type is selected, the appropriate files will appear. Click the file that you want to project. Once you have finished displaying this file, return to the file selection pane to choose your next file.
6 Set the application (available only in wireless connection) In iShow (wireless projector) app, tap the Setting button to configure appropriate settings in iShow (wireless projector) app. The menu tree where the following operations are found under the settings button vary by device and version. You can configure: SSID You may change the name of the wireless network. You may also set the network security, and set the wireless network to open or encrypted mode.
Keystone Correction You can use and to apply keystone correction to the projected screen in order to adjust it to a proper shape for easy viewing. About You can use this option to find out the current version and copyright information of your iShow (wireless projector) app.
7 Using HDMI for projection If your device supports HDMI output, you can use an HDMI cable to connect your device to the KODAK iShow 1000 Pico Projector. This allows the projector to mirror what is on your devices display. This functionality does not require the use of the iShow (wireless projector) app. Connecting via HDMI enables the projection any application that is supported on your device.
8 Firmware Update When there is a new version of firmware, follow the following steps to update the firmware of the pico projector: 1. Download the new firmware to the computer's hard drive. 2. Turn on the KODAK iShow 1000 Pico Projector and connect to the power charger. 3. Use the wireless network to connect the computer containing the firmware upgrade to the projector. Open a web browser, and enter the IP (192.168.203.1) to access to the firmware update interface. 4.
9 Projector Specifications Type DLP Focus Range (diagonal) 5-50inches Throw Distance Approx.16.5-165cm Resolution 854×480 pixels Image Brightness 50 Lumens Contrast Ratio 500:1 Connector Power inlet, earphone jack, HDMI Type A Speaker Mixed stereo output Support wireless network Yes Picture *.jpg, *.png; photo supports up to 24 mega-pixels Video *.3gp, *.mp4, *.mov, *.m4v; supports up to 1080p30 Supported projection file formats Microsoft ® Word ® (*.doc, *.
Supported operating systems Android 2.3.0 or higher, iOS 4.3.1 or higher, Windows 7, Windows 8 Focus Control Manual Power Built-in rechargeable Li-polymer battery 3.7V 2800mAh Capability Approx. 90 mins Operation Environment Temperature: 0 ~ 35°C, Humidity: 10 ~ 80% Storage Environment Temperature: 0 ~ 45°C, Humidity: 0 ~ 60% Product Dimension Approx. 125.0×60.0×22.5mm Product Weight Approx.
The Kodak trademark and trade dress are used under license from Kodak. © 2013 by JK Imaging Ltd. All rights reserved. JK Imaging Ltd. 1411 W. 190th Street, Suite 550, Gardena, CA 90248, USA JK Imaging Europe, 71 Clarendon road, Watford, WD17 1DS, UK www.kodakcamera.jkiltd.com Ver.
