Digital Action Cam User Manual SP1
BEFORE YOU START Declaration of Conformity Responsible Party: JK Imaging Ltd. Address: 1411 W. 190th Street, Suite 550, Gardena, CA 90248, USA Company Website: www.kodakcamera.jkiltd.com For Customers in Canada This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
For Customers in the U.S.A. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
About this Manual Thank you for purchasing this product. Please read this manual carefully and keep it in a safe place for future reference. JK Imaging Ltd. reserves all rights to this manual. No part of this published manual may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form, by any means, without the prior written permission of JK Imaging Ltd. .
SAFETY NOTES Waterproof / Dustproof / Shockproof / Freeze-proof • Do not use or store this product in high temperature environment. • JIS / IEC dustproof grade 6 (IP6X). • Do not expose the lens to strong light sources (e.g. Daylight, etc.) for extended periods of time. • JIS / IEC waterproof grade 8 (IPX8). • Height for shockproof rating is 2.0m. • Suitable temperature range for freeze proof capability is -10°C and above. Product Notes: • Do not disassemble or repair the product by yourself.
Waterproofing Notes: • Do not use the product below 10 meters (32.8 feet) underwater. The product will remain waterproof for one hour at the depth of 10m (32.8 feet). • Do not use this product in a geothermal spring or in water at a temperature greater than 40 °C. • Please do not open the rear cover underwater. • If water accidentally comes in contact with the product, please do not open the rear cover immediately. Turn the product off, and dry it with a clean, dry and lint free cloth.
Battery Notes: • Use only the battery specified for this product. • If the battery overheats during charging or use, stop charging or use immediately. Turn off the product, remove the battery carefully, and wait until it cools down. • Do not heat the battery or throw it into a fire to avoid a possible explosion. • Please keep the battery contacts clean and dry. • When the product is stored for a long period of time, please remove the battery.
Memory Card Notes: • The memory card referred to in this manual is Micro SD Card or Micro SDHC card. • Please buy a genuine memory card of a well-known brand. • Please keep the memory card clean and dry. • When inserting a memory card, make sure the notch direction of the card matches the notch direction of the memory card mark near the card slot. Do not force the memory card into the card slot. • Before using a brand new memory card, please format the memory card first.
Other Notes: • Do not disconnect the power or turn the product off during the update process. Doing so may cause incorrect data to be written and the product may not power on later. • When using your product on an airplane, observe the relevant rules specified by the airline. • Due to the limitations of manufacturing technology, the LCD screen may have a few dead or bright pixels. These pixels do no effect the quality of the photos or video.
Contents BEFORE YOU START.............................................................. 1 SAFETY NOTES...................................................................... 4 Contents................................................................................... 9 GETTING READY..................................................................13 Accessories Included.........................................................................................13 Part Names.......................................
Operation Method...................................................................25 Turn On / Off......................................................................................................25 Set your Language, Date and Time after the first power-on.............................. 26 LCD Screen Display..........................................................................................27 Introduction to Basic Operation of Recording and Shooting..............................
Introduction to Mode Settings............................................................................43 Movie Settings Introduction...............................................................................44 Still Settings Introduction...................................................................................51 AP Settings Introduction....................................................................................54 Smart Device APP Operating Method....................................
Connection Port Introduction..................................................73 Connect a Computer..........................................................................................73 HDMI Connected TV Output..............................................................................75 APPENDICES........................................................................76 Specifications.....................................................................................................
GETTING READY Accessories Included Your product box should contain the product you purchased along with the following accessories. If anything is missing or appears to be damaged, please contact your retailer. (Based on sales in different countries or regions, the shape of the AC adapter will vary. The actual product will prevail.
Standard Lens Cover Underwater Lens Cover Standard Lens Cover has been installed on the product when leaving factory.
Part Names 1 6 1 Alignment Point 2 Standard Lens Cover 3 Microphone 2 4 Speaker 3 5 Lens Cover Ring 6 LCD Screen 5 4 15
7 8 9 10 13 12 15 14 16 11 7 Video Recording Button / Shooting Button 8 Status Indicator 9 Menu Button / Direction Button (Upper) 10 Power Button / Delete Button 11 Lens Cover Buckle 12 OK Button 13 Playback Button / Direction Button (Lower) 14 Tripod Socket 15 Location Hole
17 16 18 16 Rear Cover Open Switch 17 Rear Cover 18 Rear Cover Lock 19 Battery Lock 20 Battery Compartment 21 HDMI Port 22 Micro SD Card Slot 23 USB Port Rear Cover Open Status 20 19 21 22 23 17
Installing and Dismantling the Lens Cover Two types of replaceable lens covers are provided for the product. Standard Lens Cover: Applicable for general use. Do not use underwater. Visual angle in the air is about 160°. Will not focus underwater. Steps for dismantling the lens cover: 1. Hold the product with your left hand, and pull the lens buckle with your finger to the left end as illustrated in the picture. Hold the lens cover ring with your right hand and rotate to the OPEN arrow direction. 2.
Steps for installing the lens cover: 1. Hold the product with your left hand, and pull the lens buckle with your finger to the left end as illustrated in the photo, hold the lens cover ring with your right hand. Please select appropriate lens cover when taking videos and pictures, otherwise it will affect the image effect. 2. When three alignment points are in a straight line, buckle the lens cover to the lens, and rotate against the OPEN arrow direction.
Installing Battery and Memory Card 1. Open the rear cover First, set the rear cover lock to the right, and push the open switch of the rear cover downward. Then rotate the rear cover around the shaft direction to open upward. ① ② 20 2. Insert the battery into the battery compartment according to the negative and positive directions as illustrated in the following picture.
3. Insert the memory card into the card slot according to the direction illustrated in the picture when the product is turned off. When inserting a memory card, make sure the notch direction of the card matches the notch direction of the memory card over the card slot. Do not force the memory card into the card slot. 4. Close the battery cover First, rotate the back over around the shaft direction to close upward. The rear cover will “click” when tightly closed.
Charging Please charge after the product is turned off. 1. Connect the product to the AC adapter with a USB cable. 2. Then insert the plug of the AC adapter to the power outlet for charging. 3. You can also connect the product to your computer with a USB cable to charge the battery. If you press and hold the power button during charging to turn off the product, the charging will be stopped.
Introduction to Various Button Functions Viewfinder status refers to viewfinder of recording and shooting. To save power, if the product is not operated for a period, it will automatically enter the LCD off status. Press any button can wake LCD.
Movie Playback Button Name Single Photo Playing Back Short press: delete Fast Forwarding / Rewinding Pausing Short press: back to the initial state of the movie Power Button / Delete Button Press and hold: turn off the product 24 OK Button Photo file: no action Movie file: start playback Pause Normal speed playback Continue to play back Menu Button / Direction Button (Upper) Previous File Rewind Rewind Previous Frame Playback Button / Direction Button (Lower) Next File Forward Forward
Operation Method Turn On / Off Turn on: When the power is off, press and hold for more than 2 seconds to turn on the product; or press and hold for more than 2 seconds to turn on the product and enter the playback status. Turn off: When the power is on, press and hold for more than 2 seconds to turn off the product. If the product cannot be turned on / off normally, you can remove the battery for forced power cut.
Set your Language, Date and Time after the first power-on 1. Press and hold the 2. Press or 3. After pressing setting screen; to turn on the product and enter the language selection screen; to select language; button to select desired language, the product will enter「Date / Time」 4. Press or to adjust the date and time display format, and press display format; 5. In the date and time options, press 6. After confirming, automatically go to status.
LCD Screen Display 8. 5M 9. 10. 1. 2. 3. 00:01:23 SD 4. 11. 12. 13. 5. I N SD 6. 7. 1. Mode Display 8. Movie Size Display 2. Time Lapse Display 9. Still Size Display 3. Burst Shot Display 10. Field of View Display 4. White Balance Display 11. Remaining Recording Time Display / Number of 5. Loop recording remaining shots Display Display 6. Wind Cut Display 7. Motion detection Display Some icons will automatically hide after a 2 second display.
Introduction to Basic Operation of Recording and Shooting 1. Enter the viewfinder status mode, and press shooting mode; to switch between recording mode and 2. Align the lens to the object to be recorded, and press 3. Under the recording mode, repress the 00:56:00 SD 1234 SD 28 for recording or shooting; to stop recording.
Under shooting mode status, when the product detects a human face, a green focus frame will appear. When two or more human faces are detected, a green main focus frame and a white secondary focus frame will appear. When the product rotates around the lens axis for 180°, the display screen on the LCD is positive display. When in still and video record mode, the LCD may turn off to save power. Pressing will turn on the LCD and immediately initiate / terminate recording.
LCD Screen Display under Playback Status 12. 1/1234 1/1234 SD 3. IN SD 4. 1. 5. 7. 6. 8. 00:01:23 9. 10. 2013 07-20 12:21 11. 2. 13. 14. 00:01:23 2013 07-20 12:21 1. Movie Display 10. White Balance Display 2. Field of View Display 11. Time Lapse Display Some icons will automatically hide after a 2 second display. 3. Memory Card or Internal Memory Display 12. Display of Current number of Shots / Total Number of Shots Only displayed when playing back the movie file. 4.
Introduction to Basic Operation of Playback Single Photo: 1. When in viewfinder status mode, press pictures; to enter the playback status of video and 2. Display movie or picture files on the LCD screen; 3. Press or memory. Press to view the movies or pictures stored in the memory card or internal to return to the viewfinder status. When the memory card is inserted, only files in the memory card will be displayed, files on internal memory will not be available to display.
Movie Playback: 1. Select movie to be played back, and press to start movie playback. 00:00:47 00:01:23 2. When playing back the movie, an operation guidance will appear on the screen. You can press buttons to perform the corresponding functions.
Movie playback rewind or forward: 00:00:47 00:01:23 00:00:47 00:01:23 Movie playback pause: There will be no sound output during rewinding or forwarding.
Movie or Picture Delete: 1. Select the movies or photos to be deleted, and press to enter the Delete screen. Press or to select 「Delete」, and press to confirm; 2. After a movie or a photo is successfully deleted, the LCD will display the next movie or photo. If you wish to delete additional files, please continue per item 1 above. 3. If you want to exit the Delete screen, select 「Exit」, and press *KRKZK +^OZ 00:01:23 Movie and / or pictures cannot be restored after being deleted.
Rotation: The direction sensor comes with the product can automatically adjust the direction during file playback according to the rotating direction detected during shooting, in order to ensure that what you see are positive images. The direction of rotation refers to the direction rotating around the lens center clockwise or counterclockwise. Only when the direction sensor detects that the product has rotated for 180°, the rotation feature is effective. Rotation of 90° or 270° is invalid.
Introduction to the Setting Mode of Menu Options 1. Under the viewfinder status, press to enter first-level menu interface of the menu; 2. Press or to select「Mode Settings」, 「Movie Settings」, 「Still Settings」, 「AP Settings」 and 「General Settings」; 3. Press to confirm, and to enter the corresponding secondary level menu interface; 4. Select items with * on the secondary level menu, and press tertiary menu interface; to confirm and to enter the 5.
Menu Introduction First Level Mode Menu Settings Secondary Level Menu Movie Settings Still Settings AP Settings General Settings Movie * Movie Size * Still Size * Sound Settings Shot * Time Lapse * Burst Shot * Power Off * Loop recording * Field of View * Wireless Power Saving * Field of View * White Balance * Date / Time * Motion detection Exit * Language * Wind Cut * Format * White Balance * Copy to Card Exit * Reset Settings * FW Version Exit 37
Introduction to General Settings 10 options in the 「General Settings」 of the first level menu: • 「Sound Settings」 There are 4 options in the 「Sound Settings」: • 「Power Off」 • Volume 1 • 「Wireless Power Saving」 • Volume 2 • 「Date / Time」 • Volume 3 • 「Language」 • Off • 「Format」 Power Off • 「Copy to Card」 • 「Reset Settings」 Power Off means the product will automatically shut down after 60 seconds after the LCD is off.
The Power Off will be invalid during recording, movie playing back and wireless connecting. Wireless Power Saving Date / Time Date and time can be set during the first power on cycle. If you wish to change the date or time thereafter, please operate as the following. Wireless Power Saving mode means that after 30 seconds of remote-controlled recording with the APP, the wireless connection will automatically disconnect, but the product will continue to record.
Language Format The language can be set during the first power on cycle. If you wish to change the language thereafter, please operate as the following. Format can clear all data stored in the memory card or memory (including protected movies and photos). 1. Enter the 「Language」 in the secondary level interface and press to confirm; 2. Press or to select language; 3. Press to confirm and back to 「Language」 in the secondary level interface; 4. Press status.
Copy to Card Reset Settings Copy to Card is to copy the files in the internal memory to the memory card Reset Settings can recover all product settings to the factory defaults. There are 2 options in 「Copy to Card」: There are 2 options in the 「Reset Settings」: • Cancel • Confirm When the memory card cannot be detected by the product, options will not be displayed on the 「Copy to Card」 interface.
FW Version FW Version can display the current version. When a new version is stored in the memory card, the firmware can be updated. There are 2 options in 「Update firmware? 」: • Cancel • Confirm Update Firmware? New Ver: x.xx 42 The following operation needs to be followed to update the firmware: 1. Enter the FW Version interface, and press to enter the tertiary level menu「Update the firmware? 」. LCD will display 「New version: X.XX」; 2. Select , and press to confirm.
Introduction to Mode Settings 2 options in the 「Mode Settings」 of the first level menu: • 「Movie」: for recording movies • 「Still」: for shooting photos Mode Settings method of operation: 1. After selecting to confirm. or options, press 2. Press to enter the viewfinder status, and display your selected or status. Under the viewfinder status, directly press , to perform or status switch.
Movie Settings Introduction There are 8 options in First Level menu 「Movie Settings」: • 「Movie Size」 • 「Time Lapse」 • 「Loop recording」 • 「Field of View」 • 「Motion detection」 • 「Wind Cut」 • 「White Balance」 • 「Exit」 Movie Size Movie Size refers to the image resolution during recording.
When selecting 「WVGA120」, the sound cannot be recorded. When selecting 「WVGA120」, 「Time Lapse」, 「Loop recording」or「Motion detection」 cannot be enabled. When selecting「WVGA60」, 「Time Lapse」 or 「Loop recording」 cannot be enabled.
Time Lapse Time Lapse enables the recording of an interval of time, and splices the frames together to present a condensed video which usually requires a long period of time to complete. 2. Press , the LCD will display red font time countdown; 3. Press again to finish recording. 09 00:00:01 There are 7 options in 「Time Lapse」: • Off • 1 second • 2 seconds • 5 seconds • 10 seconds • 30 seconds • 60 seconds Time Lapse method of operation: 1.
Loop recording Loop recording allows for the recording of independent segments of movies according to selected time length from the beginning of recording. The product will continually record movies of the length selected until the record button is pressed to end recording. When the memory card is full, the product will overwrite the recorded files starting from the first movie circularly. There are 3 options in 「Loop recording」: • Off • 5 minutes • 10 minutes Loop recording method of operation: 1.
Field of View Motion detection Field of View means the image receiving angle for the product. Motion detection means that if the product detects moving objects entering into the LCD screen, it will automatically start recording. During the recording process, if there is no moving object detected for 10 continuous seconds, the recording will be automatically paused. There are 4 options in 「Field of View」: • Ultra Wide • Medium • Narrow • Water Ring Field of View method of operation: 1.
5. During recording, you may press the to stop recording. When the Motion detection feature is enabled, Time Lapse or Loop recording setting cannot be performed. When the memory card is full, ① will become red font and flashes for 2 seconds. 15:00 00:00:00 00:00:00 Movie Size cannot be selected as WVGA120.
Wind Cut White Balance Wind Cut refers to the reduction of noise caused by wind. White Balance means that the user adjusts the color temperature under different light sources to ensure that the colors are reproduced correctly. There are 2 options in 「Wind Cut」: • Off • Enable There are 5 options in 「White Balance」: Wind Cut method of operation: 1. After the Wind Cut is enabled, press to return to the viewfinder status. LCD will display corresponding icons; 2. Press to start recording; 3.
Still Settings Introduction There are 5 options in First Level menu 「Still Settings」: • 「Still Size」 • 「Burst Shot」 • 「Field of View」 • 「White Balance」 • 「Exit」 51
Still Size Burst Shot The Still Size indicates the number of pixels used to capture the images. A photo having higher image resolution contains more details and is capable of better meeting bigscreen fine photo printing requirements. Burst Shot allows ten photos to be captured continuously one single time before auto pause.
Field of View White Balance Field of View means the image receiving angle range of the product. White Balance means that the user adjusts the color temperature under different light sources to ensure that the colors are reproduced correctly. There are 4 options in「Field of View」: • Ultra Wide • Medium • AWB ( Auto White Balance ) • Narrow • Daylight • Water Ring • Cloudy • Fluorescent • Underwater Field of View method of operation: 1.
AP Settings Introduction The action cam can be wirelessly connected with your smart device. 5. The action cam and the smart device can only be connected one to one. Please review the following items before your first connection: 6. When the temperature of the battery is higher than 65 °C : 1. Your smart device system version needs to be iOS 4 or higher and Android 2.3 or higher. If not, please upgrade your smart device system version. 2.
Connection setting method of the product and the smart device: Step 1: setting up the product 1. Press in the viewfinder status, select 「AP Settings」, and press to enable wireless connection function so that the SSID interface in 「AP mode」 appears. SSID and WPA2 password messages are displayed in the interface. AP mode SSID:PIXPRO-SP1_1234 WPA2-PSK:12345678 Step 2: setting up the smart device 1. Enable the wireless function of the smart device to search surrounding wireless devices; 3.
AP mode 3. If there is a need to turn off wireless, press button or press after selecting in the SSID interface so that the selection interface appears. Select , press to turn off wireless. AP mode 2. If connect APP failed, press to return to the SSID interface, select , press , so that the selection interface appears, select , press . This will change the WPA2 password.
Smart Device APP Operating Method Position Service Function The APP supports the position service function on your device. It may record GPS information in the photo files. This function is not supported for movie files. Android system: 1. When the APP is enabled for the first time, it may prompt that 「"PIXPRO SP1" would like to use your current location」.
iOS system: 1. When the APP is enabled for the first time, if the position service is enabled, it will prompt whether to not 「"PIXPRO SP1 " would like to use your current location」; if the position service is disabled, it will prompt 「Turn on Location Services to allow "PIXPRO SP1" to determine your location」; and if clicking 「setting」, the smart device position service setting interface will appear. 2.
APP Home Playback Enter APP Home interface, and three options are displayed: • 「Playback」: enter playback state • 「Remote Viewfinder」: enter the viewfinder status and control the action cam to shoot by using the smart device • 「About」: check the version of the APP. Click 「playback」 in the APP Home to enter the playback state.
Index playback (action cam / smart device) 1. In the APP Home, click 「playback」to enter the index playback state, and enter the photo album of the action cam in default. 23:30 < 2. The index playback interfaces of the smart device and the action cam can be switched by shifting a red dot on the interface of the smart device. 3. The index playback interface of the smart device displays files downloaded from the action cam to the smart device.
Enter the selection interface after selecting , and click thumbnails so that files can be selected. Clicking the same thumbnail for the second time will cancel selection. 23:30 < itemsselected selected 22Items Setting function Click at the right upper corner of the interface so that the setting interface can appear. 23:30 < Cache can be wiped in the Android system. • : share • : slide play • : delete Cache can be wiped in the iOS, where login and logout accounts also can be set.
Download function In the index playback interface of the action cam, click to enter the download mode. Select a file to begin downloading. Downloading will be continued after switching to the index interface of the smart device, and the downloading progress bar will be displayed. 23:30 < Download : downloading : wait downloading : the download is complete : cancel download 62 : fail in downloading 23:30 < Only choose at most 20 files at the same time.
Delete function 1. In the index playback interface of the action cam, click to enter the selection interface, select the files to be deleted, click again to delete the files, and select whether or not to delete in the delete prompting interface. 23:30 23:30 < < < 7 Items selected 2.
Slide play function Clicking a photo in slide play will stop slide play and the single photo interface will appear. 1. In the index playback interface of the smart device, click to enter the selection interface; 2. Firstly, select the files to be played, and then click to start slide play; 3. If no file is selected, directly click that all files will be played.
Share function Transmission procedure is determined according to the settings of the smart device. 1. In the index playback interface of the smart device, click to enter the selection interface. 2. Select the files to be shared, and click to pop up the share option.
Single Photo In the index playback interface, the single photo interface will appear if a single file is clicked. Previous and next files can be selected to be browsed through sliding from side to side. 100% enlargement screen will appear by double clicking one single photo, and the original dimension will be recovered by double clicking again. 1.
2. Executable operations in single photo playback of the files on the smart device: Edit function: 1. Editing photo files: • : share • : slide play Click to enter the effect interface, where filter effects, brightness adjustment and modeling effects can be set. • : edit • Filter effects: • : delete The filter effects are divided into 23 types. More effect options can be viewed by sliding the effect option bar from side to side.
• Brightness adjustment effects: 2. Editing movie files: Click : Off : Auto to enter the trim interface. 23:30 < 11 / 26 23:30 < Trim • Modeling effects: : Off : centering on dot : centering on strip (lateral direction) First, click the effect your like and then click (Android system) / (iOS system) to select the options of 「saving」or uploading to social networks or「cancel」.
Steps of movie trim: ① According to the desired trim accuracy of the movie, click or to increase or shorten the number of frames. ② Slide the quick browse bar from side to side so that the vertical line stays on thumbnails needing to be cut, and click to select the trim starting point. ③ Slide the quick browse bar again to the left so that the vertical line stays on the thumbnails needing to be cut, and click to select the trim finishing point.
Field of View: Ultra Wide Medium Narrow Water Ring AWB: Video mode: 23:30 < AWB Daylight Cloudy Fluorescent Underwater 99:99 Still Size: 14M 10M 5M Burst Shot: Single • / : enter the index playback state on the action cam. Burst Shot The characteristics of these parameters are the same as the action cam.
Video mode method of operation: 1. Click icons at the top of the interface to set corresponding parameters. 2. Click click to start video recording, and to stop video recording. 3. Click state. to enter the index playback In Wireless Power Saving enabled state, a prompting message about breaking of wireless connection in 30 seconds will be popped up when video recording on the smart device.
23:30 Click「About」 in the APP Home, so that the version of the APP can be checked. < 9999 • : enter the index playback state on the action cam.
Connection Port Introduction Connect a Computer The product can be connected to the computer using a USB cable to allow for copying the files from the product into the computer. The product supports Windows operating systems (Windows XP, Windows Vista , Windows 7, and Windows 8) and the Mac operating system. Steps: 1. Open the rear cover of the product, connect one end of the USB cable to the computer (the computer needs to be in on state) and the other end to the USB port of the product; 2.
If connected to the computer USB port of 100mA, the product will have no response due to insufficient power supply. Pressing for more than 2 seconds will cause shut-down and stop of communication between the computer and the product. If a memory card is inserted in the product, only files in the memory card will be read. If needing to read the files in the internal memory, please pull out the memory card before connecting to the computer.
HDMI Connected TV Output The product is capable of realizing movie and photo playback on a TV through HDMI. The HDMI connection defaults to automatic connection mode. Steps: 1. Open the rear cover of the product, connect one end of the HDMI cable (not included) to a TV which is up to the HDMI standard (the TV and the product both need to be turned on) and the other end to the cable to the HDMI port of the product; 2. The product display will show a rolling connection cartoon; 3.
APPENDICES Specifications 「Design and specifications are subject to change without notice.」 Active Pixels 14.24 Megapixels Total Pixels 15.31 Megapixels [1/2.33" MOS] Lens Focal Length 3.0mm Equivalent to 35mm film 16.8mm F number F2.8 Lens Construction 6 groups 6 elements Optical Zoom Fixed focus Focusing Range Normal: 60cm ~ ∞ Field of View Ultra Wide, Medium, Narrow, Water Ring Anti-Handshake EIS File Format 76 Still Image Exif 2.3 (JPEG) Movie Movie Format: MOV (H.
Still Size Image Dimensions Movie Size (4:3) 14MP: 4320×3240 5MP: 2592×1944 (16:9) 10MP: 4320×2432 1920×1080(30fps), 1280×960(50fps), 1280×960(30fps), 1280×720(60fps), 1280×720(30fps), 840×480(60fps) High-Speed Movie: 848×480(120fps) Detection Features Face detection Waterproof Feature Up to 10 m underwater Shockproof Feature Up to 2 m Dustproof Feature Equivalent to JIS / IEC ( IP6X ) Freeze-proofing Feature -10°C Wireless Supported LCD Screen 1.
Burst Shot Supported Playback Modes Single Photo White Balance Auto (AWB), Daylight, Cloudy, Fluorescent, Underwater Internal Memory: Approx.
Prompts and Warning Messages Message Description When using “Copy to card”, if the number of folders in the memory card exceeds the maximum number of folders (999), the copy and access actions cannot be performed. ! MAX 999 This message indicates that a long read time may be caused due to too many folders in the product During shooting, if the files or folders have reached the maximum number (9999 for files, 999 for folders), the memory card cannot be accessed.
Message ! IN Description Reset Mode When turning on the product or pressing , the product detects that the internal memory is out of space. The message will disappear after 3 seconds. Updating firmware. User should do nothing. The product will turn off automatically after the update is completed. The memory card still cannot be recognized after format. ! 80 An error occurs when reading the memory card.
Message Description The internal memory still cannot be recognized after format. ! ! IN SD Interruption logging problem is encountered in the period of writing in the memory card or recording in the video recording or shooting process. Reset Mode The message will disappear in 2 seconds, and the screen of format or not will appear. Return to the viewfinder status will be displayed in 2 seconds.
Message Description Connecting to the computer USB Connecting to the HDMI device 82 Reset Mode The display is ended after connection is succeeded. Caution will appear before power off when the battery of the product is already dead. The firmware cannot be updated when power is insufficient. It will shut down after displaying for 2 seconds. A message appears to prompt updating after full charging and returning to the update screen.
Trouble Shooting Problem Possible causes Solution Product does not turn on The battery has been depleted. Charge the battery. Exceeded maximum folder number If the files or folders have reached the maximum number (9999 for files, 999 for folders), the memory card cannot be accessed. Copy the data to the computer disk, and format the memory card using the product.
Special Accessories Let the action cam accommodate to your activity, there are different options of accessories available. Accessories bundle vary per distribution retailer. To purchase additional accessories separately, please contact your local retailer customer service support, or visit www. kodakcamera.jkiltd.com for more customer service details.
For ease of assembly, please line up the marks on the base and pre-tightening handle per the diagrams below.
86
Adhesive mount (flat) : accessory applicable to skateboard Adhesive mount (curved) : accessory applicable to helmet 87
Installation Method: There are two types of adhesive mounts: flat and curved. You may select based on the shape of the object to be used. Both types can be assembled in the same way, taking the adhesive mount (flat) as an example: 1. Align the location pole of the base to the location hole of the action cam, and align the screw on the base to the tripod socket of the action cam. Rotate the screw for fixing.
2. Tie one end of the rope to the adhesive mount, and the other end to the rear cover shaft. 3. Assemble the base, pre-tightening handle and adhesive mount according to the direction illustrated in the picture. First press the base into the adhesive mount, and then rotate and tighten the pre-tightening handle. Pre-tightening Handle Rope Adhesive Mount 4. Tack the double-sided adhesive at the bottom of the adhesive mount to the object to be used. Double-sided adhesive is disposable.
Handlebar mount: accessory applicable to bicycle Installation Method: 1. Set the handlebar clamp to the handlebar, and rotate the screw for fixing.
2. Align the location pole of the base to the location hole of the action cam, and align the screw on the base to the tripod socket of the action cam. Rotate the screw for fixing. 3. Assemble the base, pre-tightening handle and handlebar clamp according to the direction illustrated in the picture. First press the base into the handlebar clamp, and then rotate and tighten the pre-tightening handle.
Suction mount: accessory applicable to be attached to the automotive windshield (or smooth surface) Installation Method: 1. Align the location pole of the base to the location hole of the action cam, and align the screw on the base to the Tripod Socket of the action cam. Rotate the screw for fixing.
2. Assemble the base, pre-tightening handle and suction mount according to the direction illustrated in the Picture. First press the base into the suction mount, and then rotate and tighten the pre-tightening handle. Base Pre-tightening Handle Suction Mount 3. First, clean the suction mount and the windshield, and then attach the suction cup to the windshield (or smooth surface). Press the handle to make it attached to the windscreen.
Vented helmet strap mount: accessory applicable to bicycle helmet Installation Method: 1. Expand the band first, and then thread both ends of the band into the helmet.
2. Thread both ends of the band into the buckle, and then press the buckle clamp. Buckle Buckle Clamp 3. Align the location pole of the base to the location hole of the action cam, and align the screw on the base to the tripod socket of the action cam. Rotate the screw for fixing.
4. Assemble the base, pre-tightening handle and vented helmet strap mount according to the direction illustrated in the picture. First press the base into the vented helmet strap mount, and then rotate and tighten the pre-tightening handle.
Head strap mount : accessory applicable to mount the action cam on your head Location Pole Installation Method: 1. Insert the angle bracket into the mount, align the location pole on the angle bracket to the location hole of the action cam, and align the screw on the angle bracket to the tripod socket of the action cam. Rotate the screw for fixing. Angle Bracket Screw Mount Band 2. Set the band to your head and adjust the degree of tightness.
If you need to remove the mount, please use one hand to push forward the angle bracket (as directed by arrow ①), and use a pointed object to push the buckles in the two side holes by order with another hand (as directed by arrow ②) . Then remove the angle bracket out from the mount.
Surfboard adhesive mount: accessory applicable to surfboard Plane Support (Small) Plane Support (Large) Installation Method: 1. Align the location pole of the base to the location hole of the action cam, and align the screw on the base to the Tripod Socket of the action cam. Rotate the screw for fixing. 2. Tie one end of the rope to the plane support (small), and the other end to the rear cover shaft of the action cam.
3. Assemble the base, pre-tightening handle and plane support (large) according to the direction illustrated in the Picture. First press the base into the plane support (large), and then rotate and tighten the pre-tightening handle. Base Pre-tightening Handle Plane Support (Large) 4. Tack the double-sided adhesive at the bottom of the plane support (large) and the plane support (small) to the object to be used. Double-sided adhesive is disposable. It can be purchased separately and replaced if needed.
Extended Arm: You can add one or two extended arms (except head bank mount) to each kit, to help you to adjust the mounting angle of the action cam more flexibly.
Licensed Product The Kodak trademark and trade dress are used under license from Kodak. © 2013 by JK Imaging Ltd. All rights reserved. JK Imaging Ltd. 1411 W. 190th Street, Suite 550, Gardena, CA 90248, USA www.kodakcamera.jkiltd.com Ver.