Action Cam SP360 User Manual
Before You Start Declaration of Conformity Responsible Party: JK Imaging Ltd. Address: 1411 W. 190th Street, Suite 550, Gardena, CA 90248, USA Company Website: www.kodakpixpro.com About this Manual Thank you for purchasing this product. Please read this manual carefully and keep it in a safe place for future reference. JK Imaging Ltd. reserves all rights of this document.
INDUSTRY CANADA This device complies with Canadian RSS-210. This device complies with Industry Canada license-exempt RSS standard (s).Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
For Customers in the U.S.A. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety Notes Product Notes: • Do not disassemble or attempt to repair the product by yourself. • Do handle the product properly. This product may be damaged if dropped, punctured or crushed. • Avoid directly touching the lens element, please use professional lens cleaning paper together with lens cleaning agents to wipe the lens and keep the lens clean. • Do not use corrosive, alcoholic or organic-solvent-containing cleaners to wipe this product.
• Directly editing the data on memory card is not recommended. Copy the data to your computer disk before editing is recommended. • Please turn the product off before removing the memory card. Otherwise, the memory card could be damaged. • When the product is stored for a long period of time, please backup the data on the memory card and remove the memory card. Other Notes: • Do not disconnect the power or turn the product off during firmware updating process.
Contents Before You Start.......................................................................................................................................1 Safety Notes.............................................................................................................................................4 Contents...................................................................................................................................................6 Getting Ready.........................
Modes Introduction ...........................................................................................................................................22 Wi-Fi mode ......................................................................................................................................................................... 23 Movie mode .......................................................................................................................................................
Getting Ready Accessories Included Your product box should contain the product you purchased along with the following accessories. If anything is missing or appears to be damaged, please contact your retailer. (The AC Adapter style will vary according to the power requirement from different countries or regions.
Kodak PIXPRO SP360 View 1 2 3 12 11 10 10 2 Status indicator 4 4 8 9 Glass lens cover ideo recording button / V Shooting button / OK button 3 7 6 5 8 1 NFC mark 5 Menu button / Direction button (lower) 6 ower button / Mode button / P Direction button (upper) 7 LCD 8 Microphone 9 Tripod socket 10 Buzzer 11 Side cover 12 Location hole 13 Battery cover 14 Battery cover lock 13 14 9
Mounting / Removing Lens Cover Removing lens cover: Mounting lens cover Turn the lens cover according to the illustrated direction until it separates from the SP360. Turn and firmly tighten the lens cover according to the illustrated direction. The lens cover protects the lens from being damaged (dustproof, shockproof and splashproof). Using the lens cover will not influence the image and video quality. Before mounting the lens cover, make sure the lens surface is clean and dry.
Installing Battery 1. Open the battery cover 2. Insert the battery Push the battery cover lock from "LOCK" to "OPEN" along the direction of arrow ① , push the battery cover along the direction of arrow ② , and open the battery cover along the direction of arrow ③ . Insert the battery into the battery compartment along the direction of arrow ④ (note the location of the + and - symbols) 4 3 2 1 2 Gently pull the tape upward to remove the battery.
Installing Memory Card Open the side cover, then insert the memory card into the card slot (note the direction of the memory card gap), push the bottom end of the memory card with a fingertip into the slot completely, and then close the side cover. A memory card (microSD / microSDHC) is optional and is not included in the product package. It needs to be purchased separately. Please use an original memory card which is Class 6 or higher and has a capacity of 4GB to 32GB.
Charging the Battery Please use the battery charger or AC adapter to charge the battery in an ambient temperature ranging from 10 ˚C to 35 ˚C. Charging the battery with a battery charger: 1. Place the battery into the battery charger according to the direction illustrated. Use the Micro USB cable to connect the battery charger and the AC adapter, and then plug the AC adapter into an electrical outlet. 2. The indicator light will turn red while charging.
Charging the Action Cam with a computer: 1. Place the battery into the Action Cam. 2. Use the Micro USB cable to connect the Action Cam to a computer (while the computer is on). 3. The indicator light will become orange while charging and will turn off automatically after charging is complete.
Configuration and Operation Main Screen Display Introduction Main screen displays under Wi-Fi mode Main screen displays under other modes 2 3 4 5 1 8 1. Mode 7 6 4. Battery status Movie mode 5. Motion detection (On) / Loop recording mode 6. Remaining recording time: / / / / / Time Lapse mode Number of remaining shots: none :("+9999" will be displayed when it exceeds the none 7. Unfold mode Burst mode Dome / Memory card / 3.
Power On / Off Power on: When the power is off, press and hold the button for more than one second to turn on the product. Power off: When the power is on, press and hold the button for more than one second to turn off the product. If the product cannot be powered on / off normally, you can remove the battery from the action cam to force it to power off. Start-up for language, date and time 1. Press and hold the button to turn on the product.
Introducing the Menu 1. In the main screen (except for Wi-Fi mode), press the button to enter the first-level menu interface, press the or button to select the item, and press the button to enter the corresponding secondary level menu interface. In Movie mode/Loop recording mode / Time lapse mode can enter In Snap Shot Photo mode/Burst mode can enter Movie Settings and Still Settings and General Settings. General Settings. 2.
General Settings Volume / Format Set the volume of the product. Format can clear all data stored in the memory card or the internal memory. There are 2 options: • Enable • Off When a memory card is inserted, only the card can be formatted. If you need to format the internal memory, remove the memory card first.
Movie Settings Unfold mode (for Movie mode / Loop recording mode / Time Lapse mode) Select from several different viewing effects. There are 5 options: Dome * • Front * 2 • Seg (Segment) * • Ring * • Panorama * (480P120) High speed movie: • The product shoots ultra high speed movies, and plays back with normal 30fps speed, in order to capture visually indistinguishable moments easily.
Time Lapse (for Time Lapse mode) 2. The display will show the There are 6 options: • 1 second • 2 seconds • 5 seconds • 10 seconds • 30 seconds • 60 seconds (960P50) or 1 (720P60) or 4. Press the (480P60) or (480P120) cannot be selected. Wind cut (for Movie mode / Loop recording mode / Time Lapse mode) There are 2 options: • 10 minutes Wind cut refers to the reduction of noise caused by wind.
Still Image Settings Unfold mode(for Snap Shot Photo mode / Burst mode) White balance(for Snap Shot Photo mode / Burst mode) Select from several different viewing effects. White balance means that the user adjusts the color temperature under different light sources to ensure that the colors are reproduced correctly.
Modes Introduction In the main screen display, press the button to switch modes. 6 modes are available: Wi-Fi mode , Movie mode Burst mode Wi-Fi mode , Snap Shot Photo mode , Loop recording mode , Time Lapse mode , . : THE ACTION CAM MUST BE SET TO Wi-Fi MODE IN ORDER TO BE CONNECTED TO AND OPERATED FROM A PC OR A SMART DEVICE.
Wi-Fi mode Download and Install App ●Smart Device: Download the App installation package (App name: PIXPRO SP360) to your smart device from the path below, and install it by following the instructions on the interface. For Android devices, search and download the App "PIXPRO SP360" in Google play, and install it by following the instructions on the interface. For iOS devices, search and download the App "PIXPRO SP360" in App store, and install it by following the instructions on the interface.
Connect Action Cam to smart device (or PC) with Wi-Fi. When in Wi-Fi mode, press the If you wish to disconnect, press the button to immediately disconnect and exit button to select Wi-Fi mode. button. After pressing the , press the or button to enter the wait for the connection interface. If you would like to exit WiFi completely, press the 1. Action Cam: button.
When recording is started via the App, the Recording interface will appear on Connect Action Cam to smart device with NFC the Action Cam. 1. Enable NFC mode on your smart device. 2. Use your smart device to slightly touch the NFC mark on the Action Cam; if the smart device has a prompt tone or vibration, it means the connection is successful. 3. The APP will open automatically on your smart device. The NFC feature will only be available when your smart device's screen is unlocked.
Movie mode Enables video recording. It is suitable for recording in most conditions. Operation method: Press the button to start recording. Repress the button to stop recording. Snap Shot Photo mode Enables photo shooting. It is suitable for recording in most conditions. Operation method: Press the button for photo. Loop recording mode Loop recording allows for the recording of independent segments of movies according to selected time length from the beginning of recording.
Time Lapse mode Time Lapse enables the recording of an interval of time, and splices the frames together to present a condensed video which usually requires a long period of time to complete. Operation method: Press the button to start recording. Repress the button to stop recording. 1 ① indicates that the current countdown seconds Sound cannot be recorded in this mode. Burst mode Enables ten photos to be captured continuously before auto pause.
Using Interfacing Micro USB interface Charging 13 Using an external power supply In case of low battery power, or when a long-term power supply is needed, an external power supply (AC adapter, vehicle power supply, portable power supply or other power unit) can be used instead of a battery. At this time, the setting of functions, photography, and other operations can be performed. When powered on, use the Micro USB cable to connect the Action Cam to an external power supply.
3. The Action Cam will automatically shut down when the Micro USB cable is unplugged. The Action Cam supports Windows 8/7 and Mac OS X (V10.6.8~V10.9) systems. If there is a memory card inserted into the Action Cam, only the files in the memory card will be read. If you want to read files in the internal memory, please remove the memory card before connecting to the computer. Micro HDMI interface The Action Cam can play back videos and photos on a TV through a Micro HDMI cable. Set up as follows: 1.
Appendices Specifications Design and specifications are subject to change without notice. Image Sensor Lens Anti-Handshake Type 1/2.33" MOS Effective Pixels 16.36 Megapixels Total Pixels 17.52 Megapixels Focal Length 0.805mm Equivalent to 35mm film 8.25mm F number F2.
Splashproof Equivalent to JIS/IEC IPX5(Body) Shockproof Up to 2m Dustproof Equivalent to JIS/IEC (IP6X) Freeze-proofing -10°C LCD 1.0 inch TN LCD Level Gauge 2-axis ISO Sensitivity Auto (100~800) Exposure Metering Method Artificial Intelligence AE (AiAE) Exposure Control Method Program AE Burst Supported White balance Auto (AWB), Daylight, Cloudy, Fluorescent, Under water Recording Media Internal Memory: Approx.
Prompts and Warning Messages Message Description There are too many files which may cause a delay to power on. When pressing the button for shooting, the memory card cannot be accessed because there are too many folders. When turning on the product or pressing the button, the product detects that the memory card is out of capacity. When turning on the product or pressing the button, the product detects that the internal memory is out of capacity.
Message Description Processing mode File processing (saving, formatting, etc.) time exceeds 2 seconds. User should do nothing. Connecting to the computer USB. The display will disappear after connection is successful. Connecting to the HDMI device. A warning for low battery before shutting down automatically. The firmware cannot be updated when power is insufficient. Charge or replace with a new battery. Updating firmware. User should do nothing.
Trouble Shooting Problem Product does not turn on Possible causes The battery has been depleted. Solution Charge the battery. The battery is installed incorrectly. Please follow the charging instructions in the manual to install the battery. Blurred images There is dirt on the lens or the glass lens cover. Clean with a clean, lint-free dry cloth. Failed to connect Wi-Fi Wrong password entered. Please re-enter the password.
Special Accessories There are different options of SP-360 accessories available. Accessory bundles vary per retailer. To purchase additional accessories separately, please contact your local retailer customer service support, or visit www.kodakpixpro.com for more customer service details. Before using (especially in water or strenuous activity), please pay attention to make sure the product is tightly secured to prevent damage or loss of the product.
Standard Housing: For use with other accessories when waterproofing is not required Installation method: 1. First, insert the adapter into the bottom of the standard housing before using the set screw to tighten. Adapter Set screw 2. Place the Action Cam inside the standard housing, and press the lock downward until it locks tightly.
Waterproof Housing: F or use with other accessories underwater, in rain, on the seashore, or in other circumstances where waterproofing is required Installation method: 1. First, insert the adapter into the bottom of the waterproof housing before using the set screw for tightening. Adapter Set screw 2. Remove the Action Cam's glass lens cover , place the Action Cam into the waterproof housing, put in the anti-fog inserts, and press the lock downward until it locks tightly.
Flat Adhesive Mount: For tacking onto a skateboard or other flat objects Curved Adhesive Mount: For tacking onto a helmet or other curved objects Installation method: There are two types of adhesive mounts: flat and curved. You may select based on the shape of the object to be used. Both types can be assembled in the same way, take the adhesive mount (flat) as an example: 1. Assemble the adhesive mount or the waterproof housing ( 36 / 37). 2.
Bar Mount: For mounting on bicycle handlebars, sailing masts, and other tube-like objects Installation method: 1. Assemble the standard or waterproof housing. ( 36 / 37). 2. Set the bar clamp to the handlebar and rotate the screws to tighten. 3. Assemble the adapter, pre-tightening handle and bar clamp in accordance with the direction illustrated in the picture. First press the adapter into the bar clamp and then rotate and tighten the pre-tightening handle.
Suction Cup Mount: For attachment to automotive windshields (or smooth surfaces) Installation method: 1. Assemble the standard or waterproof housing ( 36 / 37). 2. Assemble the adapter, pre-tightening handle and suction mount in accordance with the direction illustrated in the picture. Press the adapter into the suction mount before rotating and tightening the pre-tightening handle. 3. First, clean the suction mount and the windshield before attaching the suction cup to the windshield.
Vented Helmet Strap Mount-A: For mounting on hollow objects like bicycle helmets Installation method: 1. Align the locator pole on the mount to the locator hole on the Action Cam, and align the screw on the mount to the Action Cam's tripod socket. Turn the screw with a coin or similar shape object to tighten. 2. Spread out the band before threading both ends into the helmet. Thread both ends of the band into the buckle, and then press down on the buckle clamp.
Vented Helmet Strap Mount-B: For mounting on hollow objects like bicycle helmets Installation method: 1. Align the mount’s locator hole with the Action Cam's locator hole and align the screw on the mount with the Action Cam's tripod socket. Turn the thumb screw to tighten. 2. Spread out the band before threading both ends into the helmet. Thread both ends of the band into the buckle, and then press down on the buckle clamp.
Head Strap Mount: For wearing on one’s head Installation method: 1. Assemble the standard or waterproof housing ( 36 / 37). 2. Insert the base of the standard or waterproof housing to the mount before using the set screw to tighten. 3. Place the band around your head and tighten appropriately.
Surfboard Adhesive Mount: To be tacked onto watersports equipment like surf boards Plane Support (Large) Plane Support (Small) Installation method: 1. Assemble the waterproof housing ( 37). 2. Tie one end of the rope to the plane support (small), and the other end to the waterproof housing. 3. Assemble the adapter, pre-tightening handle and plane support (large) in accordance with the direction illustrated in the picture.
Quick Clip: suitable to be clipped on a belt or harness Installation method: 1. Align the locator pole on the Quick Clip to the locator hole on the Action Cam, and align the screw of the Quick Clip to the Action Cam tripod mounting hole, and screw it in to tighten. 2. Clip the clip onto a belt. Extended Arm: You can add one or two extended arms (except head strap mount) to each kit, to provide more flexibility to adjust the mounting angle of the Action Cam.
Licensed Product The Kodak trademark and trade dress are used under license from Kodak. © 2014 by JK Imaging Ltd. All rights reserved. JK Imaging Ltd. 1411 W. 190th Street, Suite 550, Gardena, CA 90248, USA www.kodakpixpro.com Ver.