Installation Guide

Premium Downlight Kit
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
Premium Downlight Kit Options
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
WARNING – Risk of fire of electric shock. Disconnect power at fuse or circuit breaker before
installing or servicing.
1. WARNING – Risk of fire or electric shock. Lighting installation requires knowledge of electrical
systems. If not qualified, do not attempt installation. Contact a qualified electrician.
2. WARNING – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal
or other sharp objects.
3. This product is designed to be used with NM (Romex) cables only. Strain relief slots are provided
to accommodate the NM cables. Do not use BX (armored) cables. They will not fit into the strain relief
slots.
4. This fixture is an IC type fixture. Some insulation types that meet this requirement are
blanket batting/roll and blown-in loose fill. Do not install in a ceiling with spray foam type
insulation. Any part of the fixture may come in direct contact with combustible material, such as a
ceiling joist or floor board.
5. This fixture requires an existing ceiling surface, such as drywall, for installation. To install this
fixture, a hole needs to be made into the ceiling surface at the desired location. Then, power supply
wiring (NM cable) needs to be installed from the power source to the hole.
6. This fixture is designed for ceiling surfaces that are 1 1/4’’ thick or less. Do not use this fixture on
ceiling surfaces that are thicker than 1 1/4’’.
7. This fixture may be installed over a wet or damp location such as a shower stall or bathtub
enclosure. The area above the ceiling surface must, however, be a dry location.
8. Min. temperature rating of -25°C.
9. Do not make or alter any open holes in an enclosure of wiring or electrical components during kit
installation.
Installing the fixture
1. Choose the location for the fixture, taking into consideration the 5’’ depth clearance requirement,
the location of ceiling joists and the accessibility for the electrical supply. Mark the selected location
with a circle using the provided template.
2. Using a keyhole saw to cut out a hole in the ceiling surface (Fig. 1). For cutout dimensions, refer to
Table 1 below. Note: Be sure not to make the hole any larger than specified by the table. An
oversized hole may not allow for proper installation.
3. Run non-metallic (NM) cable (also known as Romex) from your source power to the first hole,
providing 6’’ (15.2cm) to 8’’ (20.3cm) of slack extending below the hole. Cable up to 12 AWG may be
used (Fig. 2) (Warning – Use cables having wires rated 90˚C or more.).
4. Loosen one of the Phillips head screws on the junction box cover and swivel the cover open. Insert
5”-6” of the NM cable into the junction box through one of the provided strain-relief slots (Fig. 3.1). If
daisy-chaining to another downlight, insert the next section of NM cable into the other strain-relief slot
(Fig. 3.2).
5. Remove at least 3" of the cable’s outer sheath and remove the plastic or paper over-wrap. Strip
approximately 3/8" of insulation from the ends of all supply wires. Using the wire connectors, make
the following wire connections within the junction box (Fig. 3.1). For connecting multiple fixtures
together, refer to Fig. 3.2. NOTE: this fixture does not require a ground wire. Connect ground wires
in supply cables with wire connectors.
WHITE Fixture Wire to WHITE( NEUTRAL) Supply Wire
BLACK Fixture Wire to BLACK( HOT ) supply wire
Supply GROUND Wire to Supply Ground Wire
6. Carefully push the wires and the wire connections into the junction box. Close to the junction box
cover. Tighten the fastening screw.
7. Adjust brightness and light color settings to the desired level (Fig. 4).
A) Brightness Settings:
The brightness settings adjust the lumen output of the light. The size, number, and layout of lights in
a space will determine the need for higher or lower lumen outputs. Since the KODO Premium
downlights are considered “high-lumen,” adjusting the maximum brightness may be desired so that a
user will not have to install a dimmer, or so that a user will not have to continually dim lights that are
too bright for an application. For example, the 5” Premium downlight delivers over 1,100 lumens at
the highest setting (see see Wattage and Lumen Performance chart at end of installation
instructions). Mounted at 8’ in a living room or bedroom might be too much light. A typical downlight
delivers around 700 lumens. For these types of applications, consider a low or medium setting. In a
kitchen or areas with high ceiling heights, a higher lumen output may be desired, so the high setting
may be best. Keep in mind that no matter what brightness setting is chosen, the lights are still
dimmable down to 10% output with an approved wall switch dimmer.
B) Light Color Settings:
The light color settings adjust the color temperature (K) of the LEDs. The KODO Premium
downlights adjust in color temperature from 2700K (warm white) all the way to 5000K (daylight).
Application type and personal preference usually dictate the color temperature needed. Most
residential applications utilize 2700K or 3000K- more of a yellowish hue. Commercial offices and
outdoor settings typically use 4000K or 5000K- more of a bluish hue. While most consumers will
choose the factory setting of 2700K, it is mostly personal preference.
Product Model Cut Out Diameter
3’’ Premium Downlight Kits 3 1/2’’
4’’ Premium Downlight Kits 4 1/4’’
5’’ Premium Downlight Kits 5 1/4’’
3’’ Premium Gimbal Kits 3 3/4’’
4’’ Premium Gimbal Kits 4 1/2’’
(Table 1)
Light Color
Daylight
Warm Light
Brightness
High
Med
5000K
4000K
3500K
3000K
2700K
Low
10. Continue inserting the fixture into the hole, while continuing to squeeze the spring-loaded clips.
When the clips are mostly through the hole, release them and push the fixture until both clips flip
down onto the backside of the ceiling surface (Fig. 6).
11. If you are installing the Premium Gimbal Kit, pull out the gimbal head and twist to desired
direction (Fig. 7). The gimbal can be rotated to 40 degrees vertically and 350 degrees horizontally.
Use the indentation shown below to assist in pulling the gimbal head out of the housing (Fig. 8).
Dimming
Dimming performance may depend on the dimmer, the dimmer range adjustment setting (for
dimmers with brightness range adjustments), the wiring method, and/or the number of LED modules
installed onto the dimmer circuit.
● For dimmer selection, it is recommended to use one of the following dimmers:
● Before turning on the LED lights, set dimmer position at maximum before adjusting to a lower light
level.
● Please follow the dimmer control manufacturer’s instructions for the installation of all dimming
controls.
Five-year Limited Warranty
KODO warrants this product to be free from defects in materials and workmanship for five years from
the original date of purchase by the consumer. This warranty is limited to the counter replacement at
the time of purchase, with the original purchase receipt. KODO will not be liable for the loss or
damage of any kind, incidental or consequential damages of any kind, whether based on warranty
contract or negligence, and arising in connection with the sale, use or repair of the product claimed to
be defective. Some states do not allow the exclusion or limitation of incidental or consequential
damages so the above limitation may not apply to you. This warranty gives you specific legal rights
and you may also have other rights, which vary from state to state. Misuse, accident, improper
installation or maintenance will also void the warranty.
This device complies with part 15 of the FCC rules. Operation is subject to the following conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
CAUTION: Any changes made to the electronics circuit will void his equipment’s compliance with Part
15 of the FCC Rules and should not be operated.
For product questions or feedback, please visit: www.KODO.co
The black baffle trim cannot be easily removed once installed
Fig. 1
Fig. 2
Fig. 3.1 Fig. 3.2
Fig. 4
Light Color
Daylight
Warm Light
Brightness
High
Med
5000K
4000K
3500K
3000K
2700K
Low
Fig. 5
8. Raise the Premium Kit up to the ceiling hole, while simultaneously pushing the excess NM cable
into the ceiling (Fig. 5).
9. Flip up and squeeze the spring-loaded clips against the junction box, as shown, and insert the
fixture into the hole, junction box first (Fig. 5).
Fig. 6
Fig. 7 Fig. 8
350Deg
40Deg
12. Continue steps 3-11 for each additional light being installed.
Installation of the Optional Black Baffle trim
Wattage and Lumen Performance
No. Brand Dimmer Family Model
1 Lutron Skylark CTCL-153PDH-WH
2 Leviton Sure Slide R62-06674-P0W
3 Eaton Sky AL SAL06P-LA-K
4 Lutron Caseta P-PKG1W-WH-R
5 Lutron Maestro MACL-153MH-WH
6 Lutron Diva DVCL-153PR-WH
7 Eaton AL Series AAL06-C1
8 Leviton Decora R12-06672-1LW
9 Leviton IllumaTech R50-1PL06-10M
10 Lutron Toggler TGCL-153PH-WH
Picture Model Power (W) CCT (K) Light Color Finish
2700
Soft White3000
Warm White
Soft White
Warm White
Soft White
Warm White
Soft White
Warm White
Soft White
Warm White
3500 Neutral White
4000 Cool White
5000 Daylight
2700
3000
3500 Neutral White
4000 Cool White
5000 Daylight
2700
3000
3500 Neutral White
4000 Cool White
5000 Daylight
2700
3000
3500 Neutral White
4000 Cool White
5000 Daylight
2700
3000
3500 Neutral White
4000 Cool White
5000 Daylight
W
hite
C
opper
B
rushed Nickel
D
ark Bronze
W
hite
C
opper
B
rushed Nickel
D
ark Bronze
10.5
8
7.5
12
10.5
9
P
RM DLKG 3IN 10.5W 90CRI MC DIM
P
RM DLKG 4IN 12W 90CRI MC DIM
16
11.5
9.5
PRM DLK 5IN 16W 90CRI MC DIM
11.5
9
7.5
W
hite
C
opper
B
rushed Nickel
D
ark Bronze
W
hite
C
opper
B
rushed Nickel
D
ark Bronze
White
14
10.5
8.5
P
RM DLK 3IN 11.5W 90CRI MC DIM
P
RM DLK 4IN 14W 90CRI MC DIM
2700K 3000K 3500K 4000K 5000K
White w/o black trim 750 760 780 790 810
Other Finish >550 >550 >550 >550 >550
White w/o black trim 600 610 620 630 640
Other Finish >405 >405 >405 >405 >405
White w/o black trim 500 510 520 530 540
Other Finish >350 >350 >350 >350 >350
White w/o black trim 950 960 980 1000 1020
Other Finish >650 >650 >650 >650 >650
White w/o black trim 750 760 780 790 810
Other Finish >550 >550 >550 >550 >550
White w/o black trim 600 610 620 630 640
Oth
er Finish >400 >400 >400 >400 >400
High 16 White w/o black trim 1100 1110 1140 1160 1180
Medium 11.5 White w/o black trim 850 860 880 895 915
Low 9.5 White w/o black trim 700 710 725 735 755
High 10.5 All Finish
650
680 730 760 790
Medium 8 All Finish 500 520 560 590 610
Low 7.5 All Finish 450 470 510 530 550
High 12 All Finish 750 785 845 885 915
Medium 10.5 All Finish 650 680 730 760 790
Low 9 All Finish 550 575 615 645 665
Finish
Lumens (lm)
PRM DLKG 3IN 10.5W 90CRI MC DIM
PRM DLK 3IN 11.5W 90CRI MC DIM
11.5
9
7.5
High
Medium
PRM DLK 4IN 14W 90CRI MC DIM
14
10.5
8.5
PRM DLK 5IN 16W 90CRI MC DIM
PRM DLKG 4IN 12W 90CRI MC DIM
Power (W)
Low
High
Medium
Low
Model
indentation