Table of Contents Safety Instructions.............................................................................................................................3 General Safety Instructions.......................................................................................................3 Installation........................................................................................................................................4 Cleaning..........................................................
PVR (Personal Video Recorder).................................................................................................21 PVR File System...........................................................................................................................21 PVR Guide......................................................................................................................................22 Time shift......................................................................................
Safety Instructions General Safety Instructions Risk of electric shock. DO NOT OPEN! Do not attempt to service the television yourself, as opening or removing the covers may expose you to dangerous voltage or other hazards. Refer all servicing to the Kogan customer support team. To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. The television should not be exposed to dripping or or splashing, and no liquid filled objects such as vases should be placed on the case.
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them may be fatal. Always turn the set off when it is not being used. Unplug the television from the power outlet when it will not be used for a long time or when there is an electrical storm.
Do not place this television near water, for example near a bathtub, wash bowl, kitchen sink, laundry tub, swimming pool or in a damp basement etc.. When moving the television to a warm location from a cold location, allow some time for any dew or condensation inside the television to evaporate fully before you turn the unit on. To prevent injury, the television must be securely attached to the floor/wall in accordance to the supplied installation instructions.
General Description • • • • • • • • • • • • Zero X radiation complies to green environment protection requirements Connect to computer directly to create a TV/Monitor combo MHL2.0 Android4.2 USB 3.0 16:9 widescreen Auto tuning and fine tuning.
Overview Back Panel You can connect the TV to video devices such as DVD/Blu-Ray players, VCR and video cameras as well as gaming consoles. Front Panel The buttons on the lower left panel control your TVs basic functions. For advanced features you must use your remote control. 1 Power Switch Press to turn the TV on or off. 2 Remote control Sensor Aim the remote at this spot on the TV. 3 Power Indicator 4 INPUT Toggles between all of the available input sources.
Remote Control 8
Note: Before turning off the main power, or turning off the power supply, you must switch the television into standby mode by pressing the POWER button on the remote control or on the television set itself. Once the television is in standby mode, you may turn off the mains power supply.
Installing Batteries in the Remote Control Notes • One load of batteries should last a year under normal use. • If you do not intend on using the remote control for an extended period of time, remove the batteries to avoid leakage. • Do not mix old and new batteries together. • The batteries should not be exposed to excessive heat such as direct sunlight, fires or similar situations. External Connections Antenna Connection Antenna input impedance of this unit is 75ohm.
Basic Operation Turning the TV on and off 1. Insert the power cord into a power outlet. 2. If the TV is in standby mode, press the POWER button on the remote control or the “ ” button on the bottom panel of the LED TV. 3. Normal picture will be displayed on the screen after approximately 15 seconds. If no signal input is detected, “NO SIGNAL” will be displayed on the screen. 4.
Arrow buttons: the selected menu item will be outlined in orange. OK button: enter the menu option that you have selected. INPUT button: You will enter the relevant option directly. The state icons at the top right corner are as follows: 1. Add to home screen 2. All caps 3. Change Wallpaper 5. Setting 6. Mass Storage 7. Wired 4. Search Note: 1. The first area as shown in the image will display the current video image. When there is no signal, it will display a snowflake. 2.
Menu System TV Menu Menu button: Open the TV menu. Exit button: Close the TV menu. Arrow buttons: Select the setting which you want to change. OK button: Enter the selected settings menu. Note: Enter the function option by click the status bar. Sound Sound Mode You can select the type of special sound to be used when watching a given settings broadcast. Your TV has five sound settings (“Standard”,“Music”, “Movie”,“Sports”, “User”) that are preset at the factory. 1.
Equalizer 1. Press ▲/▼ key to select an equalizer item. 2. Press OK key to enter the equalizer submenu. The sound settings can be adjusted to suit your user preferences. 1. Press ▲/▼ key to select a particular item. 2. Press ◀/▶ key to decrease or increase the value of a particular item. Note: The adjusted values are stored according to the selected particular item.
Image Picture Mode Your TV has five picture settings (Standard, Soft, Vivid, User, Dynamic) that are preset at the factory. Only "User" mode can be set to your preference by adjusting particular items such as Contrast, Brightness,Color,Sharpness,Tint. Press ▲/▼ key to select "Picture Mode" option. Press ◀/▶ key to select one picture mode. Aspect Ratio You can select the picture size which best corresponds to your viewing requirement. Press ▲/▼ key to select “" option.
Program Auto Search Press ▲/▼ key to select "Auto Search" option. Then press OK key to start a notice window. In this notice window, you can select country in the “Country Selection” option and set “Tune Type” option. The number of searched channels will be shown on the screen. If you set “Tune Type” to “DTV+ATV”, once searching for DTV channels is over, the TV will start to search for analog channels. (Please note, Australia no longer has analog TV signals).
Program Edit You can use ▲/▼ button to choose “Program Edit” and enter the menu, press the Blue/Red/Yellow colour button on the remote control to skip, delete and move programs, also you can press FAV button to add to your favourite list. • • • • Delete: You can press RED button to enter "DEL" menu, then choose the channel you want to delete and press RED button again to delete. Move: You can press the ▲/▼ button to choose the channel in ATV mode you want to move and press YELLOW button to move it.
2 - Input Source Menu 1. Press MENU key to display the main menu on the screen. 2. Press / key to select "Input Source” option. 3. Press OK key to enter submenu. Note: The TV can support 4K2K mode (3840×2160) in HDMI4 mode. Function OSD Setting You can modify the OSD set to suit your user preferences. 1. Press ▲/▼ key to select the “OSD Setting” option. 2. Press OK key to display the OSD setting menu.
enter password" menu will appear. Enter your 4digit password to enter the “Lock” submenu. (The default password is 0000, and the master password is 1980). Lock System 1. Press ▲/▼ key to select the “Lock System” option. 2. Press ◀/▶ key to select "On" or "Off". Set Password 1. Press ▲/▼ key to select "Set Password" option. 2. Enter your 4-digit password to set the old password. Choose any 4-digits for your new password and enter them. Once the 4 digits are entered, the cursor will go to “Confirm password”.
RGB Range Change the brightness and saturation for a better picture. 1. Press ▲/▼ to select "RGB Range" option. 2. Press ◀/▶ key to select "16~235" or "0~255". Note: only available in HDMI mode, please select the appropriate setting according to the DVD Player/STB. Game Mode (Used only in HDMI and VGA) Game mode will deal with input lag and might improve your gaming experience. 1. Press ▲/▼ to select "Game Mode" option. 2. Press ◀/▶ to select "On" or "Off".
Notes: • The sleep timer you have set will be cancelled when the TV turns off or if a power failure occurs. • When the time is less than 60 seconds, remind information will be displayed on the screen. Press any key button to cancel timer function. Time Zone You can choose it to modify your time zone in the TV set. 1. Press ▲/▼ key to select "Time Zone" option. 2. Press ◀/▶ key to select time zone.
NOTE: The larger your device the longer it will take to format. The device may take many minutes to format, this is not a malfunction, please wait for the formatting to finish. • Speed Check: Test your disk speed. PVR Guide If the disk for PVR is ready, the programs can be recorded in DTV mode. Time shift In DTV mode, press “▶/▋▋” button to pause the DTV program, press it again to continue play. The length of time a program can be paused depends upon the setting in the PVR File System.
DTV EPG (Electronic Program Guide) In DTV mode, press “GUIDE” button to enter the Electronic Program Guide. At Guide menu, press "RED” button to "Record" Setting. In the Guide menu, press "OK" button to enter "Reminder Settings". Note: Press ◀/▶ button to adjust the scheduled time, press OK button to save the setting. Press the BLUE button to enter the Schedule interface.
Digital Media Player This TV is embedded with one USB port digital media player. It can find devices that support USB 1.1/2.0/3.0, including flash drives, USB hard disks and digital cameras. Note: please do not remove the cable or device during the data transfer. Doing so may cause problems for the system.
External Connection Connecting a VCR 25
Connecting a Camcorder 26
Connecting a DVD Player/Blu-Ray Player/Set-Top Box via DVI 27
Connecting a DVD Player/Blu-Ray Player/Set-Top Box via HDMI 28
Connecting a Digital Audio System 29
Connecting to PC Each PC has a different back panel configuration. 1. Connect a D-Sub Cable between the VGA/PC IN connector on the TV and the PC output connector on your computer. 2. Connect a PC audio cable between the PC AUDIO IN jack on the TV and the Audio Out jack of the soundcard on your computer.
Assembling the Stand If you need to remove or assemble the stand, please read the following: • Before attaching/detaching the stand, be sure to turn the TV off. • Before performing any work, spread cushioning out over the base area to lay the TV on. This will prevent it from being damaged. Assembly Instructions 1. Fix the bracket at the stand with the three screws. (Fig. 1) 2. Assemble the stand to the back of the cabinet. Fasten the stand together using the two screws. (Fig. 2) 3.
Wall Mounting Instructions Your LED TV is able to accommodate wall mounting with the use of a wall mount bracket (not supplied with the LED TV) and the mounting holes on the back of the unit. We recommend removing the TV stand prior to wall mounting the TV. 1. Find the four mounting holes where you want to mount, according to the wall hanging bracket (3), then drill these four holes into the wall. 2. Drive Nylon sleeves (2) into the mounting holes on the wall. 3.
Troubleshooting If you have any problems with your television, please check the suggested solutions below, as these issues may be caused by improper adjustment/setup rather than a malfunction with the unit. If the problem persists, please contact the Kogan customer support team.
Product Layout 34
