COLD PRESS SLOW JUICER KA12SLWJCRA
SAFETY & WARNINGS • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. • Children should be supervised to ensure that they do not play with the appliance. • Cleaning and user maintenance should not be performed by children without supervision.
• During operation, feed the food material slowly to avoid blocking the rotation. Take care to avoid inserting large or hard food materials. Cereal grains and legumes soaked in water to soften. Seeds and cores should be removed. o If blockage occurs, stop working immediately. Reverse the motor for a while then open the lid to take out the food and continue working again in the forward (“On”) motor setting. • Use the special pusher stick to feed food material into the feeder opening.
OVERVIEW Top cover Pusher Smart cap Juicing bowl Screw Fine strainer Container Cleaning brush Note: The illustrations above are for reference only and the product may differ slightly in appearance.
ASSEMBLY STEP 1 Topset assembly Align the red dots ●on each part and assemble in the order shown. Once assembled, turn the drum lid clockwise to close. STEP 2 Topset and base assembly Place the bowl on the base, the 3 holes of bowl lock into the 3 feet at the base.
For safe operation • Operating the juicer without ingredients can cause damage to the screws. • Do not continuously operate the juicer for more than 10 minutes. This can damage the motor from overheating. • After continuous use, let the juicer rest for 10 minutes before starting another session. • If the juicer stops due to the overload protection, let the juicer cool for 30 minutes to 2 hours before juicing again. • Do not put fingers or other objects into the food chute.
2. Place the juicing screw into the strainer. Turn and press down on it until it clicks into place. Note: • • • The juicer may leak if not assembled properly. Ensure that the compression silicone and silicone ring are assembled properly. The juicing screw needs to be locked in-place in order to close the drum lid. 3. Place the strainer into the juicing bowl ensuring the red dot on the strainer is aligned with the red dot on the juicing bowl.
4. Place the drum lid on to the juicing bowl aligning the red dot on the drum lid with the red dot on the juicing bowl. Turn clockwise to close, aligning the red on the drum lid with the lock mark. Step 2: Top-set and base assembly Tip: For easy assembly, hold the drum lid by grabbing the food chute and turn clockwise as shown in the above illustration.
1. Place the bowl on the base, the 3 holes of bowl lock into the 3 feet at the base. 2. To lock the juicer in-place, turn it clockwise. To unlock, turn the juicer counterclockwise.
3. Place the pulp cup under the pulp spout and place the juice cup under the juice spout as shown in the illustration. Note: • • Juicer will not operate if parts are not assembled properly, or may leak during operation. Ensure all steps have been followed correctly before operating juicer.
Disassembly Step 1: Switch OFF and unplug the power cord from the wall outlet. Note: • Extract all the remaining pulp in the juicing bowl before stopping the juicer. • For easy clean up, operate the juicer for an additional 30 seconds after the juice is extracted. • When the drum lid is stuck, press the REVERSE, OFF, then FORWARD buttons in this order, switching back and forth 2 to 3 times to dislodge.
OPERATION Step 1: After preparing the ingredients, plug the power cord into a wall outlet. Note: • • Do not touch the power cord with wet hands, it may cause electrical shock, short-circuit or fire. Check the safety of the wall outlet. Step 2: Press the ON button to operate. Note: • • On (Forward): Pulls down and slowly masticates the ingredients. RVS (Reverse): Pushes the ingredients back up to dislodge them.
Step 4: Use the smart cap to make mixed juices. Stop juice from dripping or rinse between different juices. • • • Juicing with the smart cap closed creates various mixed juices when different fruits and vegetables, milk, banana, beans etc., are selected. After juicing, close the smart cap to stop the juice from dripping, especially when disassembling the juicing bowl off the base.
TIPS ON INGREDIENTS Figure 1 Figure 2 Double size food chute: One for whole apple, another for strip shaped vegetables. 1. Open the lid to feed the whole round fruits like apples, oranges (figure 1). 2. Feed the strip shaped vegetables like carrots (figure 2).
DO NOT put the following ingredients into the juicer Hard seeds Peach, nectarines, apricot, plum, mango, etc. Remove hard seeds from the ingredients before juicing. Hard or inedible skins Pineapple, melon, mango, orange, etc. Peel the skins from the ingredients before juicing. Frozen strawberry, blueberry, raspberry, etc. Frozen fruits or ice Completely thaw frozen fruits before juicing. Do not use ice. Sesame seed, butter, margarine, etc.
INGREDIENT PREPARATION Before operating • If the juicer is jammed or if the drum lid does not open, press the REVERSE button and hold until it becomes dislodged. Repeat REVERSE-OFF-ON as needed. • Continue operating the juicer until all the ingredients in the juicing bowl are extracted. The drum lid may not open easily if there is a lot of pulp remaining in the juicer. • Every ingredient yields different amounts of juice.
• Leave the smart cap open when juicing ingredients that create excessive foam during extraction. Foam can accumulate if operated with the smart cap closed. • It is recommended that the extracted juice be consumed within 48 hours after extracting. Depending on the density of the ingredients, the extracted juice can gradually show layers over time. • If there is an excessive amount of foam, use a mesh strainer to separate it from the juice.
Hard fruits and vegetables (e.g. carrots, potato, beets & spinach): ½ -1" 6" 1" Hard fruits and Soak in cold water vegetables may put prior to juicing and excess strain onto cut to appropriate the motor and cause sizes. it to stall. To increase the juice yield, juice fruits and vegetables with high water content. Preparation tips • Slice the ingredients 1" thick or cut 1"wide and 2-6" long. • Soak hard ingredients like carrots and ginger in cold water prior to juicing.
• For pomegranate, discard the skin and juice only the inner part. Extraction tips • Depending on the size of the grapes, insert 3-5 grapes at a time while monitoring the extraction result. • Thaw frozen ingredients like pomegranate and raspberry then insert about 1 tablespoon (5g) at a time. • Frozen ingredients usually lose significant amount of fluid when thawing. When juicing, you can mix milk or yogurt to balance the fluid lost.
Extraction tips • One at a time, slowly insert the prepared ingredients. • Roll leaves into spiral as inserting into the juicer. • Insert the leafy part of the ingredients first then alternate between leafy parts and stems. • For ingredients like wheatgrass, grab a handful and insert a bundle. Caution: The fibres from tough ingredients like celery can wrap around the juicing screw and affect the juicer’s performance. Cut the stems that are thick and tough to 4" long or less.
CLEANING & CARE 1. Remove the juicing screw and strainer from the juicing bowl. Clean with provided brush. Note: • Immediately clean the juicer after each use. If remaining residue in the juicer dries up, it can make disassembling and clean-up difficult. The excess build-up can cause poor performance in future uses. • For easy disassembly, place the topset in the sink and run water through from the top of the topset.
TROUBLESHOOTING When there is no power to the juicer Low juice yield There is too much pulp in the juice • Check if the power cord is properly plugged in. • Check if the drum lid and the juicing bowl are properly assembled. • Ensure that the topset and base of the juicer have been assembled correctly, following the step by step instructions in the Assembly portion of this guide. • Juicer will not operate if parts are not assembled properly.
The drum lid doesn’t close • Make sure the juicing screw is pushed all the way into the strainer for the drum lid to close properly. • If the juicing screw is not properly in position, the drum lid may not close. • Check if the parts are assembled correctly. Try reassembling the parts and listen for the odd noise. • Do not start the juicer unless there are ingredients and/or liquid in it. • Operating the juicer without ingredients can cause damage to the screw.
• Check the power cord and make sure it is plugged in correctly. • Ensure that the juicer has been assembled correctly, following the step by step instructions in the Assembly portion of this guide. • If too many ingredients are inserted at one time, this can cause the juicer to stop. • If the juicer stops because there are too many ingredients inserted in it, press the REVERSE-OFFON button in this order, switching back and forth 2 to 3 times.
Discoloration of the plastic parts Using for purposes other than juicing • After juicing, if the juicer is not cleaned right away, the remaining pulp inside the topset can dry up, which can make disassembling and cleaning hard. This can also affect the juicer’s performance and colour. • Ingredients that are rich in carotenoids such as carrots and spinach may dye plastic parts. • When the parts are dyed with carotenoids, rub vegetable oil into the dyed areas and use mild detergent to clean.
Note: • REVERSE: Pushes the ingredients back up to dislodge them. The REVERSE button only works while holding down the switch. • Switch OFF ensuring that the juicer comes to a complete stop. Then press REVERSE. Hold the REVERSE button for 2 - 3 seconds and release. Repeat as needed. Let the juicer stop completely before using the REVERSE button to prevent malfunction. • If the juicer does not work after these steps, disassemble and clean the parts before operating the juicer again.
SPECIFICATIONS Rated voltage AC 220~240V Rated frequency 50Hz Rated power 240W Speed 60RPM
Need more information? This is a Quick Start Guide and we hope that this has given you the assistance needed for a simple set-up. For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.
