SAFETY & WARNINGS Ensure to read ofl instructions and warnings in this user guide prior to first use, Retain this user for future reference. » Do rot position the monitor on unstable surfaces, If the monitor falls, Boy led to damage and injures to people around fs vicinity, ® Do not place the monitor near heat sources Sor example, sobers, stoves, replaces), + Dio net use the monster In areas locking adequate ventilation.
dod Monitor (1) B Stand stern 1} € Stand base (1) E Mount adapter (<1) F Display Part cable Power adapter (x) H User guide ix)
Wom Bo Levee Wm ow Up baton Power button Left button Dow button Eight button HDMI port Display Port port Audio output Power port
1. Open the package and remove the foam to take out the stand stem (B) and stand base {6}, Place the components flat surface, Ensure oll components are present before disposing of any packaging. 3.Use a screwdriver (not supplied) to install the stand stern (8) onto the back of the janitor (A) with two screws (DI.
A. Align the stand base {C) with the bottom of the stand stern (Bh, Use o screwdriver to secure the stoned Bose 8) with two screws (DB). B.Use both bards to place the monitor (A) upright.
1 Open the package and revere the foam to take out the stand stern (B) and stand base Place the components flat surface. ss Hii i CR 2. Carefully remove the monitor {A and place into the lower foam cover. Take out the rent adapter E} and using a screwdriver, secure the round adopter Eo the back of the monitor (A) with two screws (OD). PR— 4. The monitor is now ready for mounting. Assemble the mount as detailed by the instructions provided.
Power adapter Connect one end of the power adapter into the power port on the monitor, then connect the ether end into a power socket, ¥ wag HOM For the monitor to receive HDMI signals from the computes, plug one end of an HDMI cable {not included) into the HDMI port on the monitor, Connect the other end into a computer's HOM output.
Display Port Far the monitor to receive Display Port signals from the computer, connect one end of the Display Port cable into the Display Port port on the mentor, Connect the other end into the Display Port output on the computer, wees [15 Celt Deluded) 09 Crag Ro Earphones Connect earphones (nok included) into the audio output port on the monitor.
OPERATION 1. Correct the monitor via HDMI Display Port. 2. Cornact the power adapter into the power port on the monitor ond power socket, Switch on the power ot the socket, AB. Press the power button on the monitor to tum ton, The indicator ght on the bottom af the monitor will Illuminate a steady blue. 4. After use, press the power bunion to turn off the monitor. Switch the power off ot the socket.
Screening display The on-screen display (OSD) menu is used to adjust the settings of the monitor, 1. Press the ght button to activate the OSD menu. 2.Press the up and down buttons to browse through the categories of settings. Press the right button to select the desired category and to enter the sub-menu, 3. Eras the up and down buttons te browse through the settings sub-menu. Crass the right button to select the desired setting. 4. Press the up and down buttons te adjust the setting.
C50 prams options Below is a table that displays the various settings options available in the OSD menu.
Brightness 0-100 Adjusts the display brightness Contrast 0-100 Adjusts the display contrast Turns the dynamiter contrast PER On off ratio mode on/off Off, Movie Mode, id al Reading Mods, Sets the contextual mode Picture | Modes Night Mode, Settings Care Eyes Mode Low Blue Light 0-100 Adjusts the level of blue light Sharpness 0-5 Adjusts the display sharpness Gamma 18,2022, Sets the gamma level of the 24, 2.6, Source display . ‘Wide Screen, . .
OSD Settings English, SL, Fel, ase Portuguese Brazil, Putsch, Netherlander, Summit, Francois NAAN LE, Language Indonesia, battalion, | Sets the OSD language EI #8, Malaysia, Pol side, Portuguese Preen, Cesspool Tom, Patience, Tiling Vig, Jk XX, Tore Sets how long the OSD O80 Ti ere Cut 5-60 rer stays on without input {in seconds} OSD H-Forestation | 0-100 Adjusts the OSD menu horizontal position OSD V-Position | 0-100 Adjusts the OSD menu vertical position ash 0-5 Sets the transparency of Transparency the O
Other Settings Selects the display input Input Signal Auto, DF, HDMI signal Audio Volume, Mute Adjusts the volume of audio Lo Tums the splicing screen Splicing Screen On, Off function SRO Auto Power On, OF Tums auto power on/off Eyelash Tums eye shield remind Remind On, Off offhand Resets the monitor to Reset Yes, No factory default settings Ips Source, . info . \information Resolution, Displays i ration bout Mode the monitor
CLEANING & CARE » Ensure the monitor is turned off, unplugged, and cooled before cleaning. = Cleo the screen by wiping it with a dry microfiber cloth, « Clean the monitor body with a slightly damp cloth with water.
Audio Audio out Yes Speakers Mo Accessorizes Power adapter Yas Displeasure cable Yes Additions functions Low blue light Yes Physical dimensions Dissensions {with stand} 542.4 x 402.8 x 608mm Dimensions {without stand) | 542.4 x 334.
Hed moss information? We hope that this user glued has given you the assistance needed for a simple set-up, For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help cosmogony began core