SAFETY AND WARNINGS Ba fore using this product, please read the following safely instructions and follow all routing safely precautions! Please rad theses instructions carefully. Please keep this book for future reference. Any operation not in compliance with these instructions is likely fo cause damages 1o the product. Warring Only qualified service technicians should disassemble, repair of modify the product Unauthorized repair may idea fo fire, electric shook or injury.
Prior o use, removal all damage-peons objects from the cleaning ares (luminous objects, fabrics, glass bottles, efc ). Otherwise i may cause damage fo these objects or affect the performance of the appliance. Please usa the cleaner with caution in the presence of children to avoid hurling them. Do not stand or sit on the vacuum cleanse so as nol io cause damage o tor injuries.
ASSEMBLY Installation of the Water Tank 1. Fill the tank with wale or any desired spastic-safe cleaning solution by removing the plastic stopper, marked with & nozzle symbol located on the top of the tank, and Fling until #is full. Reinsert the plastic stopper. Complacently dry off the water tank before inserting into the robot Certain caning solutions may need o be diluted with water before inserting into the water tank.
& Taking the sweeping bracket with the rubber extension facing up, insert the two front prongs inch the corresponding holes in the same compartment containing the roller brush. 6. Lower e left and right clips located on the sides of the sweeping bracket Info their corresponding holes until 2 cock is heard. Blot R0.NE 8 Charging Your Vacuum 1. Connect the power adapter to the power adapter seek on the charging dock. 2 Locate an circularize cutlet on the wall close (o the ground and plug in the power adapter.
Wuhan the robot has finished the planned can, | wil velum to the charging dock automatically. |t will also rectum to the charging dock automatically when it has low battery. ‘Wuhan the robot is cleaning or on the standby mode, press the “Re tum Homs® button on the resole controller, the robot will rectum lo the charging dormice Terry an the power of the robot by dipping the power switch, ™ s fum on, "0% is firm off.
Alternatively, to using the charging dock, the robot can also be changed by connecting the power adapter o the DO recharging port on the side of the robot. e e Charging Status 1. When the red/blue light on the button is bunking, the robot is charging. The charge level s below 15% when the red light blinks, and the charge e above 15% when the bite light bunks. When the bite light on the panel is solid, the robot is fully charged. 2.
Hohhot Operation 1. To start your robe, turn on the power switch on the side of the robot. The bis light on the butler will Semifinals The robot will enter standby mods. Press the button on the panel, the robot will begin the planned clean. 2. you press the button on the pane whilst the robot is cleaning, the robot wil ranter into standby mode and wait for the next instruction. 3. To send the tabor back to the charging dock manually, press the bunion on the panel two Mes.
WI-Fi mode: Use your thumb to press and hold the power bunion, wheels the Index finger presses against the anti-collision strip of the machine. When you hear the voice of "I, release the bunion and the bite light on the panel wii begin blinking. The robot will enter inch WI-Fl mode.
The device wil commences the pairing process and connect to the app, i< Add Device: ErvIn Wi Password Connecting.. Devi be added successfully 5. After successfully configuring the devices, the device will bs shown on the home gaps. Tap to enter #s control page.
CLEANING & CARE Removal and Leaning of the Dustbin 1. Press the dustbin button on the pane! 1o tee out the dustbin 2. Open the upper cover of the dustbin and pour out the dirt and debris Remove and Clearing of the Wader Tank 1. Cross the water tank bunion on the pans!, io take oul the wale tank. 2. Pen the flexible plastic inst, inject clean water and clean the water tank.
Removal and Cleaning of the Roller Brush 4. Press the lip at each end of the sweeping bracket simultaneously with both index fingers fo remove the sweeping bracket. 2. Pupil on the left end of the roller brush to remove it 3. Loan the hair off the brush or wash it with water (do not reinsert i unlit it is completely dry after washing). Removal and Cleaning of the Side Brush Gently pick up the robot and lay | with s wheals facing up. Cara fully clan the hair off of the brush.
1EE® times. cleaner is stuck on stales lase Warming Signs Gauss of suss Troubleshooting The off and Solid rad light, The left ard right Clan the hair or debris Hg ht whee's fall | one sound thees drive wheels are on the left and right o work. times. entangled wheals. Allure of the Bolls rad light, wo | The loft or right side | Clean the hale or debris side brushes. sounds three brushes ars o the left and right dimes. tangerine brushes.
Meed more information? This is a Quick Start Guide, and while we hope that this has given you the assistance needed for a dimples SST-up, a full user guide outlining all of this product’s instructions and features can be found online at help koan com kbgan.
