Installation Guide
Bypass Shower and Bath Doors
K-702200, K-702202, K-702204, K-702206, K-702208, K-702211, K-702213, K-702215, K-702219, K-702221
Installation Guide
Position the wall jambs over the bottom track.
Plumb both wall jambs. Mark the screw holes.
Remove the wall jambs. Drill 5/16” holes into the
walls and insert the anchors.
Reposition both wall jambs. Secure the wall jambs
with screws. Attach a bumper at the top and
bottom locations.
*Call Customer Care Center to order replacement parts.
**Finish/color code must be specified when ordering.
Retain this document for future servicing.
Record model number from box for reference.
CAUTION: Risk of injury. Do not attempt to cut
tempered glass.
IMPORTANT! Do not cut the top track the same
length as the bottom track.
Walls must be within 3/8" (10 mm) of plumb.
Cover drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer's
instructions for application and curing time.
Parts Identification
7
89
5
2
3
4
Bypass Shower DoorsBypass Bath Doors
Required Tools
1
6
Model Number:______________
1177731-2-A
Apply 100% silicone sealant in the groove on the
underside of the bottom track. Secure the bottom
track to the ledge along the marked location.
100% Silicone Sealant Masking Tape
32 Teeth Per Inch Blade
Miter Box
Number 2 Pencil
3/16"
5/16" Masonry Bit for Tile
5/16"
1036386**
Hardware Skin Pack
1/4" (6 mm)
Cut Line
"A" Mark
Notch
1
2
3
Screw Cover
Screw Cover
#8-18 x 1-1/2"
A
A
Groove
Tin Snips
Position the bottom track on the center of the
ledge. If needed, file the ends to match the
corners.
Center the bottom track on the ledge with the
bottom-track leg to the outside. Tape the bottom
track in place and mark the position.
Measure distance "A." Subtract 1/4" (6 mm) or
the width of a number 2 pencil from "A" and cut
the bottom track.
Important! The bottom track and wall jamb must
sit flat against the shower ledge and the wall. If
needed, trim and file the wall jamb. Use a coin to
match and to transfer the corner radius of the
shower to the wall jamb.
1
USA/Canada: 1-800-4KOHLER
Mexico: 001-800-456-4537
www.kohler.com
(5/64")
Key
1013942
(K-702200, K-702204, K-702206)
(K-702208)
(K-702202)
(K-702211, K-702221)
(K-702213)
(K-702215)
(K-702219)
1017813-01**
1017813-02**
1017813-03**
1017813-05**
1017813-06**
1017813-07**
1017813-08**
Inside-Panel Guide
(Silver)
(Brass)
(Nickel)
(Bronze)
10070.45
10070.46
10070.30
10070.72
Bottom Track
#8-18 x 3/8"
Screw
(Silver)
(Brass)
1048208-B
1048208-K
Screw Cover
1031943**
Screw
(Silver)
(Brass)
1048208-C
1048208-F
Inside Panel*
#8-32 x 3/8"
8-32 x 1/4"
Screw
1051142-A
Roller
1044585
Blind Nut
1050048-B
Bushing
1059792
Sex Bolt
1077763-A
Towel Bar
(Includes
Hardware)*
Outside Panel*
Bumper
1131838**
Wall Jamb*
Wall Jamb
Notch
#8-18 x 1-1/2"
Wall Jamb*
Wall Jamb
Notch
Top Track*
Screw Cover
1031943**
Anchor
1077762
Model Number Label
x2
x2
x2
Top Track
B
B
"B" Mark
Cut Line
1/32" (1 mm)
Measure distance “B” above the wall jambs.
Subtract 1/32" (1 mm) or the width of a saw
blade from “B.” Mark and cut the top track.
Bottom-Track
Leg
Hanger Bracket
10082.09 (Bronze)
1077761-01** (Silver, Brass, Nickel)