Installation Guide

19
22
17
Lay the inside panel flat and partially thread the
screws into the panel. Install screw covers over
the side screws.
From the inside of the shower, install the inside
panel. The uncoated side faces the outside of the
shower.
From the outside of the shower, install the
outside panel. The uncoated side faces the outside
of the shower. The outside-panel leg fits over the
bottom-track leg.
If either panel needs adjustment, remove the door
and position the rollers in a new hole to raise or
lower the glass.
Outside the shower, use 100% silicone sealant to
seal along the entire length of the wall jambs and
the bottom track.
Inside the shower, use 100% silicone sealant to
seal along the entire length of the wall jambs and
in the corners where the wall jambs meet the
bottom track.
Position the top track over the wall jambs. Either
side of the top track can face out.
For both doors, insert a bushing into each hole at
the top of the glass panels. Install the hanger
brackets over the glass panels. Align the hanger
brackets with the mounting holes.
Insert a blind nut through each hanger bracket
and bushing. Secure with a sex bolt. Do not use
power tools! Do not overtighten!
On the outside panel, assemble a roller to the
middle hole of each hanger bracket. Place the
rollers on the same side as the outside-panel leg.
10 11
1312
1177731-2-A
ONE-YEAR LIMITED WARRANTY
KOHLER plumbing products are warranted to be free of defects in material and workmanship for one year from
date of installation.
Kohler Co. will, at its election, repair, replace or make appropriate adjustment where Kohler Co. inspection discloses
any such defects occurring in normal usage within one (1) year after installation. Kohler Co. is not responsible for
removal or installation costs. Use of in-tank toilet cleaners will void the warranty.
To obtain warranty service contact Kohler Co. either through your Dealer, Plumbing Contractor, Home Center or
E-tailer, or by writing Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler, WI 53044, USA, or by
calling 1-800-4-KOHLER (1-800-456-4537) from within the USA and Canada, and 001-800-456-4537 from within
Mexico, or visit www.kohler.com within the USA, www.ca.kohler.com from within Canada, or www.mx.kohler.com
in Mexico.
IMPLIED WARRANTIES INCLUDING THAT OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE EXPRESSLY LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. KOHLER
CO. AND/OR SELLER DISCLAIM ANY LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES. Some states/provinces do not allow limitations on how long an implied warranty lasts, or the
exclusion or limitation of special, incidental or consequential damages, so these limitations and exclusions may not
apply to you. This warranty gives you specific legal rights. You may also have other rights which vary from
state/province to state/province.
This is Kohler Co.'s exclusive written warranty.
15
18
16
Symptom: Alignment
1. The top of the door panel is tilted away from the
wall.
2. The bottom of the door panel is tilted away from
the wall.
3. The door panel does not touch the bumper.
Symptom: Water Leaks
1. Water leaks between panels.
2. Water leaks between the wall jamb and
the door panel.
3. Water leaks under the bottom track.
4. Water leaks around the wall jamb area.
Symptom: Operation (open/close)
1. The outside panel is difficult to move.
2. The inside panel is difficult to move.
Recommended Action
A. Remove the door panel from the top track and lower the roller that is closest to the wall. See step 18.
A. Remove the door panel from the top track and raise the roller that is closest to the wall. See step 18.
A. Determine whether door panel top or bottom is closer to the wall, and then adjust the roller closest to the wall.
Recommended Action
A. When showering, make sure the inside panel is against the showerhead wall.
A. Adjust the door panel to line up with the wall jamb.
A. Check for proper silicone sealant application. See steps 21 and 22. Apply more silicone sealant in the leak location.
A. The notched wall jamb fits over the bottom track to cover any miscut or skewed cuts. Seal as directed to ensure
proper watertight seal. See step 22.
Recommended Action
A. Ensure a gap exists between the bottom track and the door panel. If no gap exists, lower the rollers to the next hole.
B. Ensure the panel is properly engaged over the bottom track. See step 17.
C. Ensure the rollers are properly installed. See steps 13 and 14.
D. Clean any debris in the top track groove.
A. Ensure a gap exists between the bottom track and the door panel. If no gap exists, lower the rollers to the next hole.
B. Ensure the inside-panel guide is properly secured to the bottom frame screws. See step 19.
C. Ensure the rollers are properly installed. See steps 13 and 14.
D. Clean any debris in the top track groove.
Reversible
Bushing
Blind Nut
Lower the glass.
Raise the glass.
Hanger
Bracket
Spacers
1/4"-20 Screw
Sex Bolt
Hanger
Bracket
Install both towel bars. Insert the spacers. Use a
hex wrench to tighten the screws. Do not
overtighten!
Door
Panel
Towel Bar
#8-32 x 3/8"
8-32 x 1/4"
x2
x2
x2
x2
Install the inside-panel guide onto the partially
threaded screws. The inside-panel guide fits into
the bottom-track slot.
Screw Cover
#8-18 x 3/8"
Screw Cover
#8-18 x 3/8"
Lay flat.
Roller
Label
Screw
Uncoated
Side
Outside-Panel
Leg
2120
2 © 2011 Kohler Co.
On the inside panel, assemble a roller to the
middle hole of each hanger bracket. Place the
rollers on the same side as the door-frame holes.
Door-Frame Holes
Screw
Label
Roller
#8-32 x 3/8"
Uncoated Side
14
TROUBLESHOOTING