CFI230J Indigo Quadrant Enclosure with integrated Mira Magna Shower System (646) Slide Rail Fixed Head 4 3 2 1 4 3 2 1 Kohler Daryl Limited Alfred Road, Wallasey, Wirral, CH44 7HY England Tel 44 (0)151 606 5000 Fax 44 (0)151 638 0303 www.daryl-showers.co.uk E-mail Daryl@daryl-showers.co.
Fit top cap - Water delivery side Fit top cap - Non Water delivery side C C Introduction C The following pages aim to provide comprehensive installation instructions, plus advice on how to care and maintain your product. We recommend that the unit is installed by a qualified Plumber or Engineer. Please retain this document for future reference.
COMPONENTS Fixed Head Water Delivery Only Carefully lift the Water Delivery System column and place the bottom into the wall jamb Standard Top Caps Lintel LH Seal Cap x2 Be very careful not to scratch or damage the tray Parking Block Side Panel Support the weight of the column. Plug the electrical cable into the connector on the cable from the Water Delivery System Caution RH Door Nylon Grub Screw x2 STEP 42 Blanking Cap Support the weight of the column.
Fit the Suppression Ferrite close to the Water Delivery connector COMPONENTS Slide Rail Water Delivery Only (See Step 42 for the Fixed Head Water Delivery) Note: The Suppression Ferrite is packed with the Digital Mixer Place the cable in the suppression ferrite.
ENCLOSURE INSTALLATION Non Water Delivery Side only Loosely fit wall channel into glass panel jamb Fit roller securing caps to both top roller brackets. Caps will ‘click’ and lock in place Carefully lift the assembly onto the tray. The end of the glass panel fits into slot ‘A’ on the tray. The wall channel end sits on the flat section of the tray ‘B’ Lift bottom roller up and tighten the fixing screw with a 3mm allen key.
Loosen the screw fixing the bottom roller to the glass with a 3mm allen key Locate other side of glass door panel between the roller and plastic glass guide Check the wall channel is vertical and mark through the 3 holes ‘A’ Drill 3 x 6mm holes Fit the splash guard to the bottom of the panel.
Ensure glass panel is vertical Drill 4 x 3mm holes through jamb into wall channel Check glass is vertical. If not remove screws, re-drill and re-fit as required. Re-fit rubber strip over screws ±0mm Fit the fixed roller to the tray on the same side as lintel wall fixing, applying sealant on the edges. Note: The seal ‘A’ on the glass panel will need to be pulled away, to allow the roller to be fitted, and re-fitted afterwards.
Remove the lintel from glass and remove the parking block 1. Match parking block to mark on wall 2. Spot drill hole positions 3. Drill holes with 6mm drill Carefully lift the assembly onto the tray. The end of the glass panel fits into slot ‘A’ on the tray. The wall channel end sits on the flat section of the tray ‘B’ Adjust wall jamb until glass is parallel to the edge of the tray ‘A’ and vertical at ‘B’. ±0mm B 4. Plug holes 5. Screw parking block to wall 6.
Check the wall channel and jamb is vertical. Loosen screws ‘A’ to adjust from side to side. Re-tighten screws The edge of the glass should fit against the end of the slot in the tray ‘B’. To adjust the glass loosen the 4 screws ‘C’ and move the panel until it is the correct postion. Re-tighten screws C Loosely fit the parking block into the wall mount ‘A’. Lift the lintel onto the glass.
The Daryl Care Programme USER INSTRUCTIONS Hint - these User Instruction pages can be separated from the Fitting Instruction pages if desired Keeping your enclosure beautiful throughout its lifetime is easy with products from the Daryl care programme Using state of the art bespoke machinery combined with the latest technology, all Daryl doors and panels are coated with a glass protector in highly controlled factory conditions.
Spray Settings CLEANING The handset has three different spray actions: Start, Soothe and Massage and an Eco setting. To adjust the spray setting turn the spray plate as follows: 1. Start - Water flows from the outer set of holes. To select the Start setting, turn the spray plate anticlockwise from the full clockwise position until it clicks once. The unit should be cleaned regularly. Use a non abrasive cleaner (ideally with a pH value of 4 to 8) applied with a soft cloth.
TROUBLESHOOTING The information below gives details on what you can do as a user should you encounter difficulties whilst operating the shower. If there is a problem with the shower control some of the push buttons will flash very fast.
COMMISSIONING/SETTING 1. General 1.1. Turn on the water supply to the Digital Mixer. 1.2. Check for leaks over the complete system. 1.3. Turn on the electrical supply to the Digital Mixer. For the Pumped Version with the Slide Rail System, pump priming can be helped by removing the handset and lowering the end of the hose into the shower tray. 2.