Installation Guide

ManualsBrandsKOHLER ManualsHome DecorRevival 28-1/2 in. x 26-1/8 in. Wall Mirror in Vibrant Brushed Nickel



113319-2-EA(-)



REVIVAL

ACCESSORIES

BEFORE YOU BEGIN

A. HOW TO USE THESE INSTRUCTIONS

Please read these instructions carefully to familiarize

yourself with the required tools, materials, and installation

sequences. Follow the sections that pertain to your

particular installation. This will help you avoid costly

mistakes. In addition to proper installation, read all

operating and safety instructions.

All information in this manual is based upon the latest

product information available at the time of publication.

Kohler Co. reserves the right to make changes in product

characteristics, packaging, or availability at any time

without notice.

B. PRODUCT NOTES

 Give some thought to the exact location desired for

these products. While it is possible to mount these

products on any surface, it is best to find a wall stud

to secure them to.

 Use a level to ensure that the centerline for the wall

bracket(s) is vertical. Use a level to ensure that the

post centerlines are level.

       

NOTE: For the K-16145 Mirror, do not drill the

mounting holes for the second support plate until the

actual product is measured.

DANGER: Risk of personal injury. These products

are not designed or intended for use as a grab bar or

support bar. Do not install any of these products in any

area where they are likely to be used inadvertently as

a grab bar or support bar. For additional information,

ASTM F446 defines critical support areas.

C. ORDERING INFORMATION

 Towel ring K-16140. . . . . . . . . . . . . . . . . . . . . . . . . . .

 Toilet tissue holder K-16141. . . . . . . . . . . . . . . . . . .

 Soap dish K-16142. . . . . . . . . . . . . . . . . . . . . . . . . . .

 24” glass shelf K-16143. . . . . . . . . . . . . . . . . . . . . . .

 Mirror K-16145. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Robe hook K-16146. . . . . . . . . . . . . . . . . . . . . . . . . .

 Towel bar, 30” K-16147. . . . . . . . . . . . . . . . . . . . . . .

 Towel bar, 18” K-16148. . . . . . . . . . . . . . . . . . . . . . .

 Tumbler holder K-16149. . . . . . . . . . . . . . . . . . . . . .

 Towel bar, 24” K-16150. . . . . . . . . . . . . . . . . . . . . . .

 Towel shelf K-16155. . . . . . . . . . . . . . . . . . . . . . . . . .

D. REQUIRED TOOLS AND MATERIALS

 Tape measure

 Assortment of screwdrivers

 Level (24” or longer)

 Pencil

 Electric drill with 5/16” bit

 1/8” hex head wrench

 3/32” hex head wrench (K-16143)

 Adjustable wrench

 Clean strap wrench

 Hammer

NOTE: Site preparation and wall finishing may require

additional tools and materials.

Summary of content (12 pages)

PAGE 1
REVIVAL ACCESSORIES BEFORE YOU BEGIN A. HOW TO USE THESE INSTRUCTIONS Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. Follow the sections that pertain to your particular installation. This will help you avoid costly mistakes. In addition to proper installation, read all operating and safety instructions. All information in this manual is based upon the latest product information available at the time of publication.
PAGE 2
ROUGHING-IN INFORMATION Determine the exact mounting location desired. With the exception of the K-16156 grab bar, do not locate these products in critical support areas. Allow adequate clearance. K-16142 4-3/4” K-16143 K-16147 K-16148 K-16150 4-7/8” 3-1/4” 24-3/8” 3-1/4” 5-5/8” 3-1/4” K-16147: 30” K-16148:18” K-16150: 24” 4-3/4” K-16149 K-16140 3-1/4” 5-7/16” 5-7/16” K-16146 3-1/4” 5-1/6” 28-1/2” 3-1/4” K-16141 3-13/16” 8-1/8” 3-3/4” K-16145 9-3/4” 25-1/2” 10-1/2” K-16155 Fig.
PAGE 3
TOWEL SHELF AND GRAB BAR INSTALLATION A. K-16155 TOWEL SHELF 1. 2. 3. 4. Shelf Support Loosen the setscrew at the bottom of each shelf support. Then remove the brackets from inside the shelf supports. NOTE: Use care to avoid scratching the product finish. Secure the three shelf sections to the shelf supports (large section on top; small section on bottom) using the hex screws provided. Tighten securely. Refer to the roughing-in information on Page 2.
PAGE 4
3. For multiple-post accessories, confirm that the center points are level. NOTE: There is no provision for later adjustment if the center points and resulting pilot holes for multiple-post accessories are not level. Multiple-Post Accessory Center-to-Center Points Wall Plate Hole Locations Fig. #5 C. DRILL PILOT HOLES 1. 2. Carefully drill 5/16” mounting holes at all the pilot hole locations previously marked.
PAGE 5
WALL PLATE INSTALLATION A. INSERT WALL ANCHORS 1. 2. Press and hold the legs of a wall anchor (provided) together, and insert the wall anchor legs into the hole. Insert all wall anchors into the pre-drilled mounting holes. With a hammer, carefully tap each wall anchor until all are flush with the finished surface. Fig. #7 B. SPREAD ANCHORS AS NECESSARY 1. 2. 3. If the wall anchor was inserted into a space between the studs, it will be necessary to spread the wall anchor legs.
PAGE 6
5. If the wall anchors are inserted into a hole in a wall stud, the legs will remain together and provide proper support. Fig. #10 C. SECURE WALL PLATE TO ANCHORS 1. 2. 3. Anchors Orient a wall plate with the large mounting hole down as shown. Secure with supplied panhead screws into the centers of the mounting holes. Repeat for all wall plates supplied. Wall Plate Panhead Screws Large Mounting Hole Fig. #11 113319-2-EA(-) 6 Kohler Co.
PAGE 7
SINGLE POST ACCESSORY INSTALLATION Wall Plate A. K-16141 TOILET TISSUE HOLDER 1. 2. 3. 4. Start setscrew into hole in tissue holder assembly as illustrated. Align tissue holder assembly over wall plate. Tighten setscrew. Insert tissue holder spindle into tissue holder assembly. Tissue Holder Assembly Setscrew Tissue Holder Spindle Fig. #12 B. K-16140 TOWEL RING 1. 2. 3. 4. 5. Wall Plate Set the large end of each insert into the post openings as illustrated.
PAGE 8
Robe Hook C. K-16146 ROBE HOOK 1. 2. 3. 4. Place robe hook through hole in post and secure with knob as illustrated. Start setscrew into hole in post. Align post over wall plate. Tighten setscrew. Wall Plate Post Setscrew Knob Fig. #14 D. K-16149 TUMBLER HOLDER 1. 2. 3. 4. 5. 6. Start setscrew into hole in post as illustrated. Thread rod into holder subassembly. Place sleeve over rod, place rod through post, and secure with knob. Align post over wall plate. Tighten setscrew.
PAGE 9
Insert E. K-16142 SOAP DISH 1. 2. 3. 4. 5. 6. Start setscrew into hole in post as illustrated. Thread rod into soap dish. Place sleeve over rod, place rod through post, and secure with knob. Align post over wall plate. Tighten setscrew. Place insert into soap dish recess. Soap Dish Wall Plate Rod Sleeve Post Knob Setscrew Fig. #16 Kohler Co.
PAGE 10
MULTIPLE-POST ACCESSORY INSTALLATION Post A. K-16147, K-16148 TOWEL BARS 1. 2. 3. 4. 5. Knob Place towel bar through one post and secure with a knob. Place a ferrule, small end first, over open end of towel bar. Place sleeve over open end of towel bar. Place a ferrule, large end first, over open end of towel bar. Align second post over towel bar assembly and secure loosely with knob. Post Ferrule Sleeve Ferrule Knob Towel Bar Fig. #17 6. 7. 8. 9. Start a setscrew into each post hole as illustrated.
PAGE 11
7. Start setscrews into brackets of bracket assembly. Check that screws do not protrude into the recesses for the shelf. 8. Wet ends of shelf with a mild soap solution. 9. Carefully slide shelf into position in brackets; adjust bracket assembly alignment as necessary. 10. Tighten setscrews to secure bracket assemblies to wall plates. Bracket Assembly Setscrew Bracket Assembly Setscrew Shelf Fig. #20 C. K-16145 MIRROR Screw 1. 2. Post 3. 4. 5. Place mirror face down on a flat, padded surface.
PAGE 12
6. 7. Measure the distance between the center-lines of the two posts. Install second wall plate to this dimension. (See Site Preparation and Wall Plate Installation, pages 3-6.) Measure Distance Fig. #22 8. 9. Have a helper align and place mirror assembly over wall plates. Secure with setscrews. Wall Plate Setscrew Mirror Assembly Fig. #23 113319-2-EA(-) 12 Kohler Co.