Installation Guide Hotel Handshower and Slide Bar K-8520 M product numbers are for Mexico (i.e. K-12345M) Los números de productos seguidos de M corresponden a México (Ej.
Thank You For Choosing Kohler Company We appreciate your commitment to Kohler quality. Please take a few minutes to review this manual before you start installation. If you encounter any installation or performance problems please don’t hesitate to contact us. Our phone numbers and website are listed on the back cover. Thanks again for choosing Kohler Company.
Finished Wall 1/2" Nipple Escutcheon 9/16" (1.4 cm) Wall Elbow Vacuum Breaker 1. Install the Wall Bracket Install a 1/2″ nipple, extending 9/16″ (1.4 cm) from the finished wall. Apply thread sealant to the nipple. Apply a ring of plumbers putty or other sealant to the back of the escutcheon according to the putty manufacturer’s instructions. Thread the escutcheon and wall elbow to the nipple. Securely tighten with a sturdy screwdriver inserted into the outlet.
Bracket Bracket Washer Top Screw Housing Tab Top Housing Slotted Hole Ring Top Cover Front View 2. Install the Top Bracket IMPORTANT! The slide bar must be mounted to stud framing supports at both the top and bottom. Wall anchors will not support the slide bar. NOTE: This accessory should not be installed in the area 24″ (61 cm) to 48″ (121.9 cm) from the floor (the critical support area as defined in ASTM F446). Separate the top cover and housing by pulling firmly. Remove the ring.
Screw Soap Dish Bracket Bracket Ring Bottom Housing Tab Top Hole Bottom Hole Front View Washer Washer Stop Screws 3. Install the Bottom Bracket Press the bottom cover housing tab, and separate the housing from the bracket. Using a tape measure and level, make a pencil mark on the finished wall exactly 22-3/4″ (57.8 cm) down from the center of the top bracket assembly. Push the stop out of the bracket. Center the bracket over the mark, and mark the top and bottom hole locations.
Screw Soap Dish Ring Larger Indent Housing Tab Bottom Housing Stop Back View 4. Install the Soap Dish Press the stop in place in the bracket. Fit the housing over the bracket, and snap it into place. Assemble the ring to the housing with the indent over the housing tab. Install the soap dish to the housing. Secure with the provided screw. 088148-2-AB 6 Kohler Co.
Top Housing Notch Button Notch Ring Top Cover Slide Slide Bar Notch Slide Bar Soap Dish 5. Install the Slide Bar CAUTION: Risk of product damage. Take care to avoid scratching the soap dish with the slide bar. Grasp the slide bar with the button and holes in bar facing up. With the holes facing to the front and back, press the slide button and position the slide to the right or left as desired. Fit the top cover over the top of the slide bar. Slip the ring over the slide bar with the tab side down.
Wall Elbow Vacuum Breaker Handshower Screen Washer Handshower Hose Gasket Hose 6. Install the Handshower Fit the gasket into the hose. Securely wrench tighten the hose to the vacuum breaker. Flush water through the system. Install the screen washer in the remaining end of the hose. Securely hand tighten the handshower to the hose. Check the handshower for proper operation. 088148-2-AB 8 Kohler Co.
Guide d’installation Douchette d’hôtel et barre coulissante Outils et matériels Perceuse et mèches assorties Mètre ruban Niveau à bulles Crayon à papier Tournevis cruciforme Merci d’avoir choisi la compagnie Kohler Nous apprécions votre engagement envers la qualité Kohler. Veuillez prendre s’il vous plaît quelques minutes pour lire ce manuel avant de commencer l’installation. Ne pas hésiter à nous contacter en cas de problème d’installation ou de fonctionnement.
Mur fini Mamelon de 1/2" Applique 9/16" (1,4 cm) Coude mural Reniflard 1. Installer le montant mural Installer un mamelon de 1/2″ s’étendant à 9/16″ (1,4 cm) du mur fini. Appliquer un ruban d’étanchéité sur le mamelon. Appliquer du mastic de plombier ou un produit semblable au dos de l’applique selon les instructions du fabricant du mastic. Visser l’applique et le coude du mur au mamelon. Bien serrer avec un tournevis inséré dans la sortie.
Support Support Logement supérieur Anneau Couvercle supérieur Rondelle Vis Languette Logement supérieur Trou rainuré Vue avant 2. Installer le support supérieur IMPORTANT ! La barre coulissante doit être montée aux support du cadrage de l’axe aux deux extrémités. Les montants du mur ne supporteront pas la barre coulissante. REMARQUE : Cet accessoire ne devrait pas être installé aux environs de 24″ (61 cm) à 48″ (121,9 cm) du sol (l’endroit critique de support tel que défini dans ASTM F446).
Vis Savonnière Orifice supérieur Orifice inférieur Support Support Anneau Arrêt Vue avant Logement inférieur Languette Rondelle Rondelle Vis 3. Installer le support inférieur. Presser la languette de couverture inférieure et séparer le logement du support. En utilisant un mètre ruban et un niveau à bulle, faire une marque au crayon sur le mur fini exactement à 22-3/4″ (57,8 cm) du centre de l’ensemble de support supérieur. Pousser l’arrêt à l’extérieur du support.
Vis Savonnière Anneau Entaille la plus large Languette de logement Logement inférieur Stop Vue arrière 4. Installer la savonnière Presser l’arrêt dans le support. Encastrer le logement sur la fixation et presser en place. Assembler l’anneau au logement avec l’entaille sur la languette de logement. Installer la savonnière dans le logement. Sécuriser avec la vis fournie. Kohler Co.
Logement supérieur Encoche Bouton Encoche Anneau Couvercle supérieur Glissière Barre coulissante Barre coulissante Savonnière Encoche 5. Vérification de l’installation ATTENTION : Risque d’endommagement du produit. Veiller à ne pas rayer la savonnière avec la barre coulissante. Maintenir la barre coulissante avec le bouton et les trous faisant face vers le haut. Avec les trous face à l’avant et derrière, presser le bouton de glissière et positionner la glissière à droite ou à gauche selon le désir.
Vérification de l’installation (cont.) Tirer le logement supérieur et la barre coulissante et les maintenir en place. Bien serrer la vis du logement supérieur pour assurer une force maximale. Assembler l’anneau dans le logement supérieur avec l’entaille sur la languette du logement. Glisser le couvercle supérieur et l’engager en place fermement. Kohler Co.
Reniflard Coude mural Douchette Rondelle à grille Flexible de douchette Joint d'étanchéité Flexible 6. Installer le support de la douchette Introduire le joint dans le flexible. Sécuriser à la clé le tuyau au reniflard. Purger l’eau dans le système. Installer la rondelle à grille dans l’extrémité restante du flexible. Sécuriser à la main la douchette au flexible. Vérifier le bon fonctionnement de la douchette. 088148-2-AB Français-8 Kohler Co.
Guía de Instalación Ducha de mano y barra deslizante para hoteles Herramientas y materiales Taladro y brocas surtidas Cinta métrica Nivel Lápiz Destornillador de punta de cruz (Phillips) Gracias por elegir los productos de Kohler Apreciamos su elección por la calidad de Kohler. Dedique unos minutos para leer este manual antes de comenzar la instalación. En caso de problemas de instalación o de funcionamiento, no dude en contactarnos.
Pared acabada Niple de 1/2" Chapetón 9/16" (1,4 cm) Codo mural Válvula rompevacío 1. Instale el soporte mural Instale un niple de 1/2″ que sobresalga 9/16″ (1,4 cm) de la pared acabada. Aplique cinta selladora de roscas al niple. Aplique una tira de masilla de plomería u otro sellador en la parte posterior del chapetón según las instrucciones del fabricante del sellador. Enrosque el chapetón y el codo mural en el niple. Apriete bien con un destornillador robusto inserto dentro de la salida.
Soporte Soporte Arandela Alojamiento Tornillo superior Lengüeta Alojamiento superior Anillo Cubierta superior Orificio ranurado Vista frontal 2. Instale el soporte superior ¡IMPORTANTE! La barra deslizante debe estar montada a los soportes de la estructura de postes, tanto arriba como abajo. Los anclajes murales no podrán sostener la barra deslizante.
Tornillo Jabonera Soporte Soporte Anillo Alojamiento inferior Lengüeta Arandela Arandela Fiador Orificio superior Orificio inferior Vista frontal Tornillos 3. Instale el soporte inferior Presione la lengüeta de la cubierta inferior y separe el alojamiento del soporte. Utilice una cinta métrica y un nivel para marcar una señal con lápiz en la pared acabada a exactamente 22-3/4″ (57,8 cm) desde el centro de montaje del soporte superior hacia abajo. Saque el fiador del soporte.
Tornillo Jabonera Anillo Muesca grande Lengüeta del alojamiento Alojamiento Fiador Vista posterior inferior 4. Instale la jabonera Coloque el fiador empujándolo en el soporte. Coloque el alojamiento sobre el soporte y encájelo en su lugar. Monte el anillo en el alojamiento, con la muesca sobre la lengüeta del alojamiento. Instale la jabonera en el alojamiento. Fíjela con el tornillo suministrado. Kohler Co.
Alojamiento superior Muesca Botón Muesca Anillo Soporte deslizante Cubierta superior Barra deslizante Barra deslizante Jabonera Muesca 5. Instale la barra deslizante PRECAUCIÓN: Riesgo de daños al producto. Tenga cuidado de no rayar la jabonera con la barra deslizante. Sostenga la barra deslizante con el botón y los orificios en la barra orientados hacia arriba.
Instale la barra deslizante (cont.) Tire del alojamiento superior y la barra deslizante hacia abajo y sosténgalos bien en su lugar. Apriete bien el tornillo del alojamiento superior para asegurar la máxima resistencia. Monte el anillo en el alojamiento superior con la muesca sobre la lengüeta del alojamiento. Deslice la cubierta superior hacia arriba y encájela bien en su lugar. Kohler Co.
Válvula rompevacío Codo mural Ducha de mano Arandela de rejilla Manguera de ducha de mano Empaque Manguera 6. Instale la ducha de mano Encaje el empaque en la manguera. Fije la manguera en la válvula rompevacío y apriete bien con una llave. Haga circular agua por el sistema. Inserte la arandela de rejilla en el otro extremo de la manguera. Fije la ducha de mano en la manguera y apriete bien con la mano. Compruebe que la ducha de mano funcione correctamente. 088148-2-AB Español-8 Kohler Co.
088148-2-AB
088148-2-AB
088148-2-AB
USA: 1-800-4-KOHLER Canada: 1-800-964-5590 México: 001-877-680-1310 kohler.com ©2004 Kohler Co.