Installation Guide Whirlpool Trim Kit K-9694 K-9695 K-9696 K-9697 K-9698 Français, page “Français-1” Español, página“Español-1” 1025430-2-B
Thank You For Choosing Kohler Company We appreciate your commitment to Kohler quality. Please take a few minutes to review this manual before you start installation. If you encounter any installation or performance problems please don’t hesitate to contact us. Our phone numbers and web site are listed on the back cover. Thanks again for choosing Kohler Company.
1. Remove the Flexjet Assembly (If Needed) Grip the jet removal tool tightly in your hand. Turn the jet ball nozzle completely upward. Insert the tool with the hook end up and catch the inside top of the ball as shown. Press your thumb against the bath wall and firmly pull out the jet assembly. Kohler Co.
FlexJet Housing First Shoulder FlexJet Apply silicone lubricant to o-ring. 2. Install the FlexJet Assembly NOTE: The FlexJet O-ring must be correctly positioned, must be lubricated, and must be in good condition to permit easy rotation and proper orientation of the jet. Lubricate the O-ring with silicone lubricant (supplied) to prevent noisy operation of the jet. Install the O-ring onto the first shoulder of the FlexJet.
Suction Cover Screw Plug (Plastic Trim Only) 3. Install the Suction Cover WARNING: Risk of personal injury or death. Never operate the whirlpool bath without the suction cover in place. Doing so may result in serious injury or death. If your whirlpool does not have the suction cover installed, install the necessary parts prior to using your whirlpool. NOTE: The suction cover may already be installed on your whirlpool.
Guide d’installation Jeu de garniture de baignoire à hydromassage Outils et matériels Plus: • Lubrifiant en Silicone (Fourni) • Outil pour retirer le jet (Fourni) Tournevis Merci d’avoir choisi la compagnie Kohler Nous apprécions votre engagement envers la qualité Kohler. Veuillez prendre s’il vous plaît quelques minutes pour lire ce manuel avant de commencer l’installation. Ne pas hésiter à nous contacter en cas de problème d’installation ou de fonctionnement.
1. Retirer l’ensemble du FlexJet Bien tenir en main l’outil pour retirer le jet. Tourner le jet vers le haut. Insérer l’outil avec le crochet orienté vers le haut et attraper la partie intérieure et supérieure de la boule comme indiqué. Presser fermement avec le pouce contre le bord de la baignoire et tirer fermement vers l’extérieur l’ensemble du jet. Kohler Co.
Logement du Flexjet Première épaule Flexjet Appliquer du lubrifiant à la silicone au joint torique. 2. Installez l’ensemble FlexJet REMARQUE : Le joint torique doit être positionné correctement, lubrifié, et en bon état afin d’assurer la rotation et le bon fonctionnement du jet. Lubrifier le joint torique avec le lubrifiant à la silicone (fourni) afin d’éviter le fonctionnement bruyant du jet. Installer le joint torique sur la première épaule du Flexjet.
Couvercle de l'aspiration Vis Bouchon (Garniture en plastique uniquement) 3. Installer le couvercle d’aspiration AVERTISSEMENT : Risque de blessures corporelles ou de mort. Ne jamais utiliser la baignoire à hydromassage sans son couverle d’aspiration en place. Cela pourrait entrainer des blessures sérieuses ou la mort. Si la baignoire à hydromassage n’a pas son couverle d’aspiration installé, l’installer avant l’utilisation.
Guía de instalación Juego de guarnición hidromasaje de la bañera de Herramientas y materiales Más: • Lubricante de silicona (incluido) • Herramienta para desmontar el inyector (incluida) Destornillador Gracias por elegir los productos de Kohler Apreciamos su elección por la calidad de Kohler. Dedique unos minutos para leer este manual antes de comenzar la instalación. En caso de problemas de instalación o de funcionamiento, no dude en contactarnos.
1. Retire el montaje del inyector Flexjet (si es necesario) Agarre fuertemente la herramienta para desmontar el inyector con la mano. Gire la boquilla esférica del inyector completamente hacia arriba. Inserte la herramienta con el gancho hacia arriba y agarre la parte de arriba de la bola como está ilustrado. Presione el pulgar contra la pared de la bañera y saque el montaje del inyector con firmeza. Kohler Co.
Alojamiento del inyector Flexjet Primer reborde Inyector Flexjet Aplique lubricante de silicona al empaque de anillo (O-ring). 2. Instale el montaje del inyector Flexjet NOTA: El empaque de anillo (O-ring) del inyector Flexjet debe estar correctamente colocado, lubricado y en buenas condiciones para que el inyector pueda girar fácilmente y se pueda orientar correctamente. Lubrique el empaque de anillo (O-ring) con lubricante de silicona (incluido) para evitar el funcionamiento ruidoso del inyector.
Tapa de succión Tornillo Tapón (guarniciones de plástico solamente) 3. Instale la tapa de succión ADVERTENCIA: Riesgo de lesiones personales o de muerte. Nunca haga funcionar la bañera de hidromasaje sin la tapa de succión colocada en su sitio, pues puede tener como resultado graves lesiones personales o la muerte. Si su bañera de hidromasaje no tiene la tapa de succión instalada, instale las piezas necesarias antes de usar la bañera de hidromasaje.
1025430-2-B
1025430-2-B
USA: 1-800-4-KOHLER Canada: 1-800-964-5590 México: 001-877-680-1310 kohler.com ©2004 Kohler Co.