Installation & Assembly

Bottom
Bumper
x2
Leg
5/16" Masonry Bit for Tile
5/16"
Miter Box
32 Teeth Per Inch Blade
Masking Tape
100% Silicone Sealant
1/16"
1245164-01**
Bottom Track
Guide
Bottom Right Bumper
Bottom Left Bumper
Top Track
1042862-B
1077762
Anchor
1235217**
Cleat
Screw
#8-18 x 1-1/2"
1048208-C
Bushing
1246178
Drill Template
Top Bumper
1217402
Roller
1240564**
Hanger Bracket
Inside Panel
Towel Bar Assembly
1247738**
Inside Knob
1245626**
Outside Knob
Skin Pack
[49" (1245 mm)]
1243277 (1/4" Glass)
1246176 (5/16" Glass)
1239198-01**
1239198-02**
[26" (260 mm)]
[22" (220 mm)]
Plastic Wall Jamb
[59-3/16" (1503 mm)]
[67-3/16" (1707 mm)]
[73-3/16" (1859 mm)]
1235754-01**
1235754-03**
1235754-02**
1235754-04**
1242405** (1/4", 54-1/4" x 29-3/4")
1242407** (1/4", 68-3/4" x 23-3/4")
Outside Panel
1244393** (5/16", 54-1/4" x 29-3/4")
1244394** (5/16", 60-3/4" x 29-3/4")
1244395** (5/16", 68-3/4" x 23-3/4")
1244396**(5/16", 68-3/4" x 29-3/4")
1244397**(5/16", 74-3/4" x 23-3/4")
1244398**(5/16", 74-3/4" x 29-3/4")
1242408** (1/4", 68-3/4" x 29-3/4")
1245438-01
(Grey)
1245438-02
(Black)
1245438-03
(Tan)
[52-11/16" (1338 mm)]
Plastic Wall Jamb
[59-3/16" (1503 mm)]
[67-3/16" (1707 mm)]
[73-3/16" (1859 mm)]
1235754-01**
1235754-03**
1235754-02**
1235754-04**
[52-11/16" (1338 mm)]
[60" (1524 mm)]
1241031-02
(Black, For 1/4" Thick Glass)
1241031-03
(Tan, For 1/4" Thick Glass)
1241152-01
(Grey, For 5/16" Thick Glass)
1241152-02 (Black, For 5/16" Thick Glass)
(Grey, For 1/4" Thick Glass)1241031-01
1241152-03
(Tan, For 5/16" Thick Glass)
1245574-01 (Grey)
1245574-02 (Black)
1245574-03 (Tan)
Towel Bar
[22" (220 mm)]
1239196-02**
1063621
Gasket
1239197**
Post
1212401**
Towel Bar Screw Cap
1042862-H
Screw
#8-32 x 3/4"
Screw
#8-32 x 1/2"
(5/16" Thick Glass)
(1/4" Thick Glass)
1241158
1240565
1240469-03
(Tan)
1240469-02
(Black)
1240469-01
(Grey)
1248375-02**
[60" (1524 mm)]
[26" (260 mm)]
1239196-01**
1242399**
1242401**
1242402**
1244387**
1244388**
1244389**
1244390**
1244391**
1244392**
(1/4", 54-1/4" x 29-3/4")
(1/4", 68-3/4" x 29-3/4")
(1/4", 68-3/4" x 23-3/4")
(5/16", 60-3/4" x 29-3/4")
(5/16", 68-3/4" x 23-3/4")
(5/16", 54-1/4" x 29-3/4")
(5/16", 68-3/4" x 29-3/4")
(5/16", 74-3/4" x 23-3/4")
(5/16", 74-3/4" x 29-3/4")
1248375-01**
Cut Line
"A" Mark
1/4"
(6 mm)
A
A
Backing
x2
Top View
x2
Bumper
Backing
Side
Plastic Wall Jamb
x2
1
2
3
Cleat
Sliding Shower and Bath Doors
Measure distance “A.” Subtract 1/4” (6 mm) or
the width of a number 2 pencil from “A” and cut
the bottom track.
Position the bottom track centered between the walls on
the center of the ledge. If needed, file the ends to match
the corners.
Important! The bottom bumper must sit flat against
the shower ledge and the wall. If needed, file the
bottom bumper. Use a coin to match and to transfer the
corner radius of the shower to the bottom bumper. Dry
fit the bumpers on the bottom track. If the bumpers do
not fit, the bottom track may need to be trimmed.
Once the bottom track and the bumpers sit flat against
the shower ledge and wall, center the bottom track
on the ledge with the leg to the outside and mark the
position. Apply 100% silicone sealant to the bottom of
the bottom track and tape in place.
Apply silicone sealant to the back of the bumper, and
position the bumper on the bottom track. Tape the
bumper in place until the sealant cures.
Use an alcohol wipe to clean the walls where the wall
jambs will be installed. Position the clear plastic wall
jambs into the bumpers with the backing side against
the wall. Plumb both wall jambs at the top, middle
and bottom. Temporarily tape in place, and mark the
position.
Remove the tape. Gradually remove the backing from
the wall jamb and place the wall jamb from bottom to
top along your mark. Repeat with the other wall jamb.
Slide the drill template onto the top of the wall jamb
with the “1” facing out. Mark two holes diagonally.
Using the template, drill 5/16” holes at the two
diagonal cleat marks. Remove the template and insert
the anchors.
Insert the cleat into the template above the “1.”
Sliding Bath Doors Sliding Shower Doors
1
1246160-2-B
Installation and Care Instructions
*Call Customer Care Center to order replacement parts.
**Finish/color code must be specifi ed when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________
Required Tools Parts Identifi cation
K-707000, K-707001, K-707002, K-707100, K-707101, K-707106, K-707200, K-707201, K-707206
WARNING: Risk of serious injury. Damage prior to
installation can result in glass shattering. Inspect the glass
and all parts for damage before installation.
WARNING: Risk of serious injury. Improper
installation can result in glass shattering. Follow all
installation instructions.
WARNING: Risk of serious injury. Do not cut tempered
glass. Tempered glass will shatter if cut.
WARNING: Risk of serious injury. Shower door and
side panels can shatter. Regularly inspect the glass and all
parts for damage, missing, or loose parts.
WARNING: Risk of serious injury. Always wear safety
glasses while cutting and drilling.
IMPORTANT! Do not touch the edges of the tempered glass
with tools or any other hard objects. Do not set the unframed
tempered glass directly on the floor or any hard surface.
IMPORTANT! Leave this manual for the end user.
Read these instructions before installing or using this
product.
NOTICE: The warranty does not apply to a product that has
been modified or altered in a manner other than as expressly
permitted in the Installation and Care Guide.
Walls must be within 3/8” (10 mm) of plumb.
Cover the drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer’s instructions for
application and curing time.
For care and cleaning, and other information, visit
www.us.kohler.com.
1 2
7
3
86
4
9
5
10
1246160-2-B
USA/Canada: 1-800-4KOHLER
México: 001-800-456-4537
kohler.com
Critical Information!
Important Information!
Read all instructions.