Casement Window Air Conditioner CAC10000W Owner’s Manual For more information on other great EdgeStar and Koldront products on the web, go to https://www.edgestar.com To use the EdgeStar self-diagnostic tool, go to https://support.edgestar.com V2.
Important Safety Information Warning: The water produced by the window AC is not potable or suitable for drinking. Do not drink the water drained from the unit as it contains contaminates and could make you sick. Improper handling can cause serious damage to the appliance and/or to the user. Please read the following safety information. Electrical Safety Make sure your hands are dry and not wet before operating the unit. Make sure the unit is properly grounded.
Operation of Safety Plug Note: Electrical products should not be disposed of with household waste. Please contact your local recycling center for more information on how to recycle electronic waste. Your window air conditioner is supplied with a Leakage-Current Detection and Interruption (LCDI) safety plug. This device provides protection to reduce the risk of fire due to arcing faults in the power supply cord.
Table of Contents IMPORTANT SAFETY INFORMATION ....................................................................................................................................................... I TABLE OF CONTENTS ............................................................................................................................................................................ III INTRODUCTION .......................................................................................................
Introduction Thank you for purchasing this Koldfront by EdgeStar casement window air conditioner. We hope that this purchase will be the beginning of a lasting and rewarding relationship between you and EdgeStar. We will provide the customer support and exemplary products necessary to nurture that relationship. This manual contains important information regarding the proper installation, use and maintenance of your window air conditioner.
Parts Identification CAUTION: Make sure the drain plug is firmly installed before using the unit to prevent leaking.
Preparations for Installation NOTE: You may need to contact your electrician if your room’s circuit is not able to power your unit. NOTE: To avoid risk of injury and/or product/property damage, please take the following precautions: - Two or more people are needed to properly handle and install. - Use proper lifting and carrying techniques. - Before installation, make sure to inspect the window and sill to ensure they are able to handle the weight and size of this unit.
Window Installation Instructions NOTE: These instructions are for installation in a standard slider or casement window only. If installing the unit into a casement window, open the window to the maximum amount to allow for clearance of the cabinet. If the window cannot open more than 15 ½” for the cabinet to clear the window, the entire window can be removed. If this is necessary, contact a professional to ensure proper installation.
3. Center the window platform on the newly drawn line with the inner (second) tab on the bottom of the platform pressed against the inside edge of the window track. Mark two holes on the window track or sill using the two holes on the window platform on either side of the platform tab. Remove the window platform and then drill two 9/64” holes in either the window track or sill in the two marked spots. A. Window track B. Window platform (tab). C.
8. Use a level to make sure that the platform is flat. Adjust the screws and use leveling shims if necessary. Attach Window Panel Frame and Side Panels 1. Measure the height of the window opening from the top of the window platform. Subtract 20 5/8” from this measurement and take note of the length for step 2. 2. Cut the plastic window panel along the longer side to the length measured in step 1 using a fine tooth saw. Remove any burrs with a file.
5. Cut the side channel sealing strip into two equal lengths. Remove the protective backing and apply it to the back of the side channel starting just below the window panel frame. Remove any excess length so that the seal is even with the bottom of the side channel. A. Side channel sealing strip B. Side channel C. Window panel frame Remove the Front Panel 1. Remove the two (2) front retaining screws from the front frame. 2. Gently pull the front out and lift up to release it from the case. 3.
Installing Air Conditioner Into a Slider Window NOTE: When choosing your window make sure the power supply cord is within 6 feet of a grounded 3-prong outlet. Follow the steps listed below to install the air conditioner into the window: 1. Using two (2) or more persons, safely lift the air conditioner into the windowsill on top of the previously installed window platform: The air conditioner should sit so that the window panel frame and side channels are against the top and side window jambs. 2.
4. Place the sliding window sash sealing strip between the far vertical edge of the inner window and the glass of the outer window. 5. Install the window locking bracket to lock the inner window to the base of the outer window. Use one #8x3/4” screw or #8-32x3/4” self-threading screw to fasten the window locking bracket in place. A. Window locking bracket B. Window sash sealing strip C. Inner window D. Outer window 6.
2. Secure the window panel frame to the top window jamb: Drill two 9/64” diameter pilot holes in the top window jamb that are in line with the partially plugged holes in the window panel frame. Secure the window panel frame with two #8-32x3/4” self-threading screws. If additional support is needed, two screws may be used on the sides of the panel frame as well. 3. Secure the side panels to the side window jambs: Drill two screw holes in the side channels near the bottom of the channels.
To Change Temperature: Press or hold either the Left (Decrease) or Right (Increase) button until desired temperature is seen on the digital display. This temperature will be automatically maintained anywhere between 62°F (17°C) and 86°F (30°C). To Adjust Fan Speeds: To select the speed of the fan, press the Fan Speed button which cycles through four (4) steps: Auto, Low, Medium, and High. Each time the button is pressed the fan speed mode is shifted to the next speed option.
To Operate in Fan Mode: Use this function only when cooling is not desired, such as for room circulation or to exhaust air (remember to open the vent). You can choose any fan speed you prefer. In Fan mode, the display will show the actual room temperature. In Fan mode, you cannot adjust the set temperature. Energy Saver Feature Press the Energy Saver button to initiate this feature. This feature is available in Auto, Cool or Dry modes.
Air Directional Louvers The 4-way air directional louvers allow you to direct the air flow Up, Down, Left, and Right throughout the room as needed. To adjust the air directional louvers side to side use the center handles as you move side to side. Exhaust Control The Exhaust Control allows the air conditioner to either circulate inside air (Closed) or exhaust air to the outside (Open.) The Closed position is used when maximum cooling is desired.
Remote Control Operations The included remote is a universal remote control. Some functions may be found on the remote that this model of air conditioner does not have. If an unavailable function is selected the unit will continue operating under its current running status. Use the remote control to change modes, fan speed, timer, and temperature settings as well as to set sleep mode. Note: Be careful not to drop the remote control. Do not place the remote control in a location exposed to direct sunlight.
Installing the Batteries 1. Insert a coin into the grove on the battery cover and turn it clockwise until the grove is aligned with the “unlock” symbol and remove the battery cover. 2. Insert the battery into the remote control with the Positive (+) side facing up. 3. Install the battery cover back on the remote control using a coin and turning it counter clockwise until the grove aligns with the “lock” symbol. Caution: Use only a CR2025 3V battery.
Maintenance Clean the air conditioner and filters regularly to maximize performance and efficiency, and prolong the unit’s life. Be sure to always unplug the air conditioner from the power outlet before cleaning. Air Filter Cleaning The air filter should be checked at least once a month to see if cleaning is necessary. Trapped particles in the filter can build up and potentially cause an accumulation of frost on the cooling coils. Push the vent handle to the “vent closed” position.
Normal Sounds High Pitched Chatter-High efficiency compressors may have a high pitched chatter during the cooling cycle. Sound of Rushing Air-At the front of the unit, you may hear the sound of rushing air being moved by the fan. Gurgle/Hiss-Gurgling or Hissing noise may be heard due to refrigerant passing through the evaporator during normal operation. Vibration-The unit may vibrate and make noise because of poor wall or window construction or incorrect installation.
Troubleshooting Follow the troubleshooting guide below to resolve common issues. Problem Air conditioner does not function at all. Possible Cause Wall plug is disconnected. Insert plug firmly into proper wall outlet. House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker. Power cord is tripped. Unit is turned OFF. Ribbon cable to control panel is disconnected. Loose or disconnected wiring on main PCB. Room temperature is below 62℉ (17℃).
Problem Possible Cause Dirty air filter- air restricted. Air conditioner cooling, but room is too warm - NO ice forming on cooling coil behind front grill. Air conditioner turns on and off frequently. Noise when unit is cooling. Water dripping INSIDE when unit is cooling. Water dripping OUTSIDE when unit is cooling. Room too cold Set temperature cannot be adjusted 19 Temperature is set too High. The directional louvers on the front are positioned improperly.
Specifications 20 Description of product Casement Window Air Conditioner Model CAC10000W Voltage/Frequency 115V / 60Hz Cooling Capacity (BTUs) 10000 Current 8.5A Color White Refrigerant R410A: 17.64 oz. Timer 24 Hour Dimensions WxDxH 14 1/2” x 23 1/2” x 20 7/8” Weight 76.9 lbs.
Edgestar Limited Warranty Full Two-Year Parts and Labor This product is warrantied by EdgeStar and is subject to any conditions set forth as follows: WHAT IS COVERED: For a period of TWO (2) YEARS from the date of original retail purchase, EdgeStar will repair or replace any part free of charge, including labor, that fails due to a defect in materials or workmanship.
