Table of contents Important Statement 3 Safety Precautions 3 Safe Notice for Drone Battery 4 Charging Instruction for Drone Battery 5 Check List Before Flight 5 Instruction for Drone and Transmitter 6 Pre-flight Operation Instruction 10 Functions Introduction 13 To know your APP 16 component integration 17 Spare Parts 19 Troubleshooting Guide 21 2
Important Statement Thank you for buying Kolibri’s product. People who under 14 years old must not use the product. Please read this brochure carefully before using the product. You are regarded as accepting all content in this user manual when using this drone. This product is not an ordinary toy but a piece of complicated equipment which is integrated with professional knowledge by mechanic, electronic, air mechanics, high-frequency emission etc.
(5) Safe operation Please operate the RC drone in accordance with your physical status and flying skill. Fatigue, listlessness and improper operation may increase the rate of accident. (6) Keep away from rotating parts Rotating parts like propellers or motors may cause serious injury and damage. Keep face and body away from rotating parts. (7) Keep away from heat The RC drone is made of metal, fiber, plastic, electronic components etc. Keep away from heat and sunshine to avoid distortion and damage.
Charging Instruction for Drone Battery 1. Connect the drone battery with USB cable first and then choose one of the method as below picture shown to connect with USB plug. 2. The red USB indicator light keeps bright when charging. And the light turns green when fully charged. * For faster charging, it is recommended to use an adapter with 5V 2A output current (not included) to charge the battery.
Instruction for Drone and Transmitter Drone Front A Propeller Clockwise B Propeller Counterclockwise Drone cover housing Left Right B Propeller Counterclockwise A Propeller Clockwise Rear Front Front LED (Green) Front LED (Green) Rear LED ( Red) Rear LED ( Red) Power Switch Rear Specification Drone Size Drone Weight Propeller Diameter Flying Time Drone Battery Transmitter Battery Charging Time for Drone Battery 334x334x127mm 248g 147mm Max Flying Distance/Radius 180mins 150m Max Image Transmi
Exploded View 1 2 3 4 11 18 5 12 19 6 7 14 6 15 8 9 22 10 23 16 5 14 21 15 11 4 20 6 7 17 6 9 10 24 2 16 12 4 5 6 15 13 14 6 17 3 25 4 15 5 6 14 26 6 13 8 9 9 10 10 Name No. 1 Drone Cover Housing Name No. Name No. 10 Lampshade 19 Switch 2 A propeller 11 B propeller 20 Receiver Board Holder 3 Upper Motor Cover A 12 Upper Motor Cover B 21 Power Board 4.
Transmitter Phone holder Power Switch Non-functional Left Stick (Throttle / Rudder) Non-functional Right Stick (Forward / Backward ) One button Take Off / Landing / Emergency Stop Button Heading Hold Mode High / Medium/Low Speed button Trimmer mode button Battery cover Brief Introduction for Button Functions Left Stick Move the Stick to forward / backward / left / right to fly the drone to up / down / turn left / turn right.
Battery installation: Open the battery cover on the back side of the transmitter and put 4 alkaline batteries (AA, not included) into the box in accordance with electrode instructions, as picture 1,2 shown. 4*1.5V Alkaline Batteries Picture 1 Notice: Battery Cover Picture 2 1. Make sure the electrodes are correct. 2. Do not mix new and old batteries. 3. Do not mix different kinds of batteries. 4. Do not charge the non rechargeable battery. Phone Installation Instruction: 1.
Pre-flight Operation Instruction Frequency Pairing 1. Turn on the transmitter switch (Picture 7) and the power indicator light flashes rapidly. Push the Left Stick all the way down to the lowest position and then release. The Left Stick will back to the middle position automatically. (Picture 8 / 9) The power indicator light flashes slowly, which indicates the transmitter is ready for frequency pairing. Picture 7 Picture 8 Picture 9 2.
Checklist before Flight 1. The camera is in front of the drone. Keep the drone front away from you. 2. Power on the drone and check the direction of the rotating propellers. The left front and right rear A propellers rotating clockwise while the right front and left rear B propellers rotating counterclockwise. 3. Activate(unlock) motors: Move the Left Stick and Right Stick at the same time (45 degree inward) to start the motors and repeat Picture 12 previous step again to lock the motors. (Picture 12) 4.
12 Move the stick to the right, then the drone turns to right. Move the stick to the left, then the drone turns to left. Pull down the stick, then the drone goes down. Push up the stick, then the drone flies up. Left Stick Move the stick to the left, then the drone turns to left. Pull down the stick, then the drone goes backward. Move the stick to the right, then the drone turns to right. Right Stick Push up the stick, then the drone flies forward.
Forward and backward trimmer When take off, if the drone tilts forward, press down the trimmer button, and push the right stick backwards. Otherwise push forwards. Left and right side flying trimmer When take off, if the drone tilts to left, then press down the trimmer button Trimmer mode and push the right stick to right to adjust. Otherwise push to left. Left and right turning trimmer When take off, if the drone head rotates to left,then press down the trimmer button and push the left stick to right.
Altitude Hold Mode Altitude hold mode indicates that the drone maintains a consistent altitude while allowing roll, pitch, and yaw to be controlled normally. It makes easier to control the drone for beginner and more stable for aerial photography. Push the Left Stick up (down) to fly the drone up (down) at certain altitude and then release the Stick. The Stick will back to the center position (Altitude Hold Center) as Picture 17 shown. And the drone will keep flying at Altitude Hold Center current altitude.
Front Left Front Right Left Rear Right Rear * Press down Heading hold mode button, the drone’s left and right LED will start flashing alternately, it shows the drone enters Heading hold mode, press the button again, then the LED gets solid and the drone ESC from heading hold mode. Heading Hold Mode Low Battery Alarm When the transmitter in low battery, the transmitter will beep ” di...di...di...” to remind the user to land the drone to replace the batteries as soon as possible.
Download and Install the APP: Fly Kolibri The APP is suitable for mobile phone with iOS and Android system, please download from the mobile phone software store: 1. For mobile phone with iOS system, please search Flyingsee in APP Store. 2. For mobile phone with Android system, please search Flyingsee in Google Play.
Component installation Landing gear installation diagram Install the left and right landing gear to the bottom housing position as per picture 19 show, and then use the screw driver to tighten the screws in clockwise. Rear Landing gear Picture 19 Landing gear Front Camera box installation diagram Insert the camera buckle to the drone bottom position(picture 20), and then push in correctly(picture 21). Picture 20 Camera box buckle entrance direction Picture 21 Camera wire connection diagram 1.
2. Insert the Micro terminator into the bottom housing socket as picture show (picture 23). Picture 23 Propeller installation diagram 1. Use the screw counter clockwise to pick out the screw and then pull out the damaged propeller(picture 24). 2. Replace with the same new rotating direction propeller,aim at the screw hole to install it (picture 25), then tighten the screw in clockwise. Picture 24 Picture 25 Motors installation diagram 1.
Battery installation diagram When install, you need to squeeze up and down of the battery buckle(picture 29) and then put the lipo battery aim at the drone battery slot, push into the position is fine.
XK6600-09 Receiver board holder XK6600-10 lampshade XK6600-11 Camera XK6600-12 AL main shaft XK6600-13 B Motor (Red and blue wire/ Red connector) XK6600-14 A Motor(Black and White wire/White connector) XK6600-15 Receiver board (include battery adapter board) XK6600-16 POWER board XK6600-17 Camera adapter board XK6600-18 Front LED board (Green) XK6600-19 Rear LED board (Red) XK6600-20 Micro terminator XK6600-21 Drone battery XK6600-22 USB Cable XK6600-23 Gear XK6600-24 Transmitter Important S
Troubleshooting Guide No. Problem Problem Cause Solution 1. Low battery. 1 1. Replace the transmitter battery. The 2. The battery positive pole and negative2. Install the battery in accordance with the transmitter pole are in reverse order. user manual. indicator light is off 3. Clean the dirt between the battery and the 3. Poor Contact. battery slice. 1. Indicator light is off. 2 1. The same as above 1.2.3. 2. There is interfering signal nearby. Fail to pair the drone with 3. Misoperation.
FCC Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
23 22