KH 2222 Surround Sound System with Q-Sound Operating Instructions En
KH 2222 IB v. 1.0, 04-12-2003 Kompernaß Handelsgesellschaft mbH Burgstraße 21 D-44867 Bochum, Germany — www.kompernass.
Index 1. Technical Data 4 1.1. Output ....................................................................................................................................................................... 4 1.2. Speakers .................................................................................................................................................................... 4 1.3. Dimensions (in mm)..................................................................................................
1. Technical Data 1.1. Output • • • Subwoofer.................................... 30 W (8 Ohm, THD: 1%) Front and rear speakers both ............................. 12 W (4 Ohm, THD: 1%) Center speaker ........................... 12 W (4 Ohm, THD: 1%) Power consumption................. 150 W Mains voltage ............................. AC 230 V ~ 50 Hz 1.2. Speakers Subwoofer.................................... ø 165 mm (6 1⁄2”) 4 Ohm Front and rear speakers both .............................
any container filled with water – such as e.g. vases – on the components. Attention! If water runs into the components, it can cause irreparable damage! Warning! Note: As long as the surround sound system is plugged into a power socket, it is not free of electrical current. This also applies when the surround sound system has been switched off. Take the mains plug of the surround sound system out of the power socket if it is not to be used for a longer period of time.
5. Control Elements and Displays 5.1. Front of center speaker 1. 2. 3. 4. 5. 6. 7. 8. 9. Display CD display AUX display Q SOUND display Stereo/3 channel stereo display DVD/5.1 display TV display Standby/Mute display 5.1 EXT display 3 7 2 6 4 5 9 8 1 5.2. Back of center speaker 10 11 10. Jacks for data cable 11. Terminal for speaker cable 5.3. Back of subwoofer 12 13 14 12. AUX input jack 13. TV input jack 14. CD input jack 15. DVD/5.1 input jacks 16. DISPLAY LINK jack for data cable 17.
5.4. Remote control 20. STANDBY button 21. MUTE button 22. CD button 23. TV button 24. AUX button 25. DVD/5.1 button 26. 5.1EXT button 27. STE./3STE. button 28. SURR + button 29. CENTER + button 30. RESET button 31. SW + button 32. SW – button 33. CENTER – button 34. SURR – button 20 21 25 22 26 35. Q.SOUND button 36. TREBLE - button 37. MAST.VOL + button 38. TREBLE + button 39. BALANCE.R button 40. BASS + button 41. MAST.VOL – button 42. BASS – button 43. BALANCE.
6. Preparing the Surround Sound System for Operation 6.1. Unpacking the components If you should want to dispose of the remote control of the surround sound system itself, then you have to remove the batteries beforehand! To guarantee that the remote control operates perfectly: • • • 1 Remove the components of the surround sound system • • • • 1 bass reflex active subwoofer with power cord 1 center speaker with integrated receiver 2 front speakers 2 rear speakers carefully from the packaging.
• • the end of the grey lead of the speaker cable into the red terminal and the end of the black lead of the speaker cable into the black terminal on the back of the subwoofer.
1 Insert one cinch cable into each of the cinch jacks. Note: 2 Insert the other end of the cinch cable into one of the pairs of jacks It may perhaps be necessary to adjust the settings on the connected audio/video device so that the sound playback works properly with the surround sound system. In case of doubt consult the operating instructions of the audio/video equipment. • • • AUX L/R TV L/R CD L/R on the back of the subwoofers. It does not matter which of the three pairs of jacks you use.
• • • • have positioned the components of the surround sound system in a suitable place and have connected them to the subwoofer with the supplied cables have connected the required audio/video devices with the named connecting options to the surround sound system and have connected the subwoofer to the power supply you can now use the surround sound system. To do this: • • 2 Then press the Q SOUND button. The Q SOUND function has now been switched on.
• press the buttons, you set the volume between the values -10 (minimum volume) and 10 (maximum volume). To change the volume of the subwoofer: Press the SW + button to increase the volume. Press the SW – button to lower the volume. Each time you press the buttons, you set the volume between the values -10 (minimum volume) and 10 (maximum volume). 8.3. Setting the bass and the treble You can change the intensity of the low tones (bass) and the high tones (treble) during sound playback.
F Have you perhaps not chosen the source for the sound, which you would like to play back, with the remote control of the surround sound system? Example: You would like to play back the sound of an audio/video device, which is connected to the AUX pair of jacks. Instead of pressing the AUX button, you pressed the TV button. The sound of the audio/video device connected to the AUX pair of jacks will then not be played back . 10.3.
KH IB v. ., -- Kompernaß Handelsgesellschaft mbH • Burgstraße • D- Bochum, Germany www.kompernass.