t RDS Radio Alarm KH 2295 Operating instructions
w q e r t yu io a s 2@ d 2! 2! 1( l k j h g f 2# 2$ 2%
Index 1. Intended use ���������������������������������������������������������������������������������������������������������������������������������� 7 2. Technical data �������������������������������������������������������������������������������������������������������������������������������� 7 3. Safety Instructions ������������������������������������������������������������������������������������������������������������������������� 7 4.
12. Connecting headphones to the RDS Radio Alarm ������������������������������������������������������������������ 19 13. Cleaning the RDS Radio Alarm ����������������������������������������������������������������������������������������������� 19 14. Troubleshooting ������������������������������������������������������������������������������������������������������������������������ 19 14.
RDS Radio Alarm E-Bench KH 2295 1. Intended use The RDS Radio Alarm is intended exclusively … Ú Ú as an alarm Ú for stationary operation in covered areas Ú for private, non-commercial applications. for the reception of VHF/FM radio stations 2. Technical data Power supply: 230 V ~ / 50 Hz, 5 W Reception range UKW/FM: 87,5 – 108,5 MHz 3. Safety Instructions ead the operating instructions carefully before R using the appliance for the first time and preserve this booklet for later reference.
given in the warranty card. The warranty card is supplied with the appliance. † Danger! Ú improper use of the RDS Radio Alarm no liabilty or warranty will be accepted! Equipment connected to a power supply can be damaged during a thunderstorm. Thus: The RDS Radio Alarm becomes warm when switched-on. This is not a cause for concern and is not an indication of a technical problem. During a thunderstorm, always remove the Ú plug from the power socket. 4.
5.
6. Preparing the RDS Radio Alarm for operation 1 Carefully take the RDS Radio Alarm out of the packaging. | Attention! Do not allow the RDS Radio Alarm to fall! It could become irreparably damaged. 2 Place the RDS Radio Alarm only on a level, scratch resistant and non-slip surface. The feet on the rear of the RDS Radio Alarm can be adjusted to three levels. You can thus set the slant of the RDS Radio Alarm to your wishes. However, ensure that both feet are adjusted to the same angle.
the time display from the pre-programmed Ú time “2:00” 4 Set the minute indicator by pressing the the date display fronm the pre-programmed Ú date “01-01-07”. 5 Press the button “Memory” g again once. In these cases you can … search for an RDS radio station manually. Ú This is explained in chapter 8.1.2 “Manually setting and saving radio stations”. select an RDS radio station from those autoÚ matically saved to the fixed programme positions. This is explained in chapter 8.1.
With the buttons o resp. a you can switch between both display formats. 11 When the desired indicator format is blink- ing in the display d: Wait for ca. 10 seconds, without pressing a button. The display d returns to its normal status; the time is now shown in the selected display format. The date is only shown when the radio is switched off. 8. Using the RDS Radio Alarm 8.
“3/8” j – for selection of 3 resp. Ú 8Button as the second digit of the programme 1 First of all select the first digit of the programme position number of the desired radio station. For this, repeatedly press the button “Group WEC” f. As soon as the desired figure for the first digit of the programme position is shown in in the display d: 2 Select the figure for the second digit of the two-figure programme position number. Repeatedly press the buttons “0/5” to “4/9”.
Example: To select the radio station saved at programme position 26: 2 To reduce the sound volume level: Turn the 1 When turning the volume controller, the current volume level is faded in shortly in the display d. The maximum volume level is shown at “V30”, the minimum level (muting) with “V00”. Repeatedly press the button “Group WEC” f.
MON TUE WED THU FRI SAT SUN ô æ æ æ æ æ æ æ Monday Tuesday Wednesday Thursday Friday Saturday Sunday Note: To carry out the steps 2 to 7 you have ca. ten seconds for each step. If one step is delayed, you must start again from step 2. 2 Press the button “AL1” 2! again. On the lower edge of the display d the abbreviations for all seven weekdays are shown. 3 Press the button i once. The hour indicator of the alarm time starts to blink. 4 Programme the hour indicator for the desired alarm time.
8 Press the button “AL1” 2! once. In the display d the RDS radio alarm symbol for the alarm call type Radio blinks. Press the buttons o resp. a to switch between the three alarm call types. 9 When you have selected the desired alarm call type: Press the button “AL1” 2! once. The programming for alarm time 1 is now saved.
2 To switch the alarm functions for week- ends back on again: Press the button “Group WEC” f once more. In the display d the indicator “WEC” extinguishes. 8.3 Using the timer functions of the RDS Radio Alarm 8.3.1 Programming the sleep timer With the sleep timer switched on, the radio automatically switches itself off after a programmed period of time. This facility can be used if you like to listen to music to help you fall asleep. To programme the sleep timer: 8.3.
On the selected date the alarm tone of the RDS Radio Alarm reminds you of the programmed appointment. The reminder sounds hourly between 08:00 and 23:00. Thereby, the alarm tone remains switched on for 10 minutes. To interrupt the alarm tone: Press any button. The alarm tone sounds again on the next full hour (and each following full hour on this day). To programme additional appointment reminders: Follow the steps 1 to 8 in this chapter.
10. Returning the RDS Radio Alarm to factory settings To return the RDS Radio Alarm to factory settings and to erase all programing that has been carried out: 1 Turn the RDS Radio Alarm so that the underside of it is visible to you. 2 With a pen/pencil (or other sharp pointed object) press the button “Reset” 2%. The display extinguishes for several seconds, afterwards the automatic station scanning starts. The RDS Radio Alarm is now returned to the factory settings. 11.
C Check to see if the button lock of the RDS Radio Alarm is activated. See chapter 11. “Switching on the button lock”. D Disconnect the RDS Radio Alarm from the power supply. Wait a few seconds, then reconnect it. Check to see if the malfunction is still extant. ô Note: Be aware that programming already carried out on the RDS Radio Alarm will be erased. 14.2 No or poor reception of VHF/FM radio stations A Carry out the steps described in chapter 8.1.
Dispose of the appliance through an approved disposal centre or at your community waste facility. Observe the currently applicable regulations. In case of doubt, please contact your local waste disposal centre. 16. Warranty & Service Please read the conditions for warranty and take note of the service centre addresses given on the warranty card. 17. Importer Kompernaß GmbH Burgstraße 21 D-44867 Bochum www.kompernass.
c Kompernaß GmbH · Burgstraße 21 · D-44867 Bochum www.kompernass.com ID no.