Installation Sheet

Hardwire Installation
Shock Hazard: Electric shock
could result in serious injury
or death. Make sure circuit
breaker is set to OFF before
installaon. Must be
installed by a qualified
electrician.
The sconce requires
some space in the
juncon box for the
transformer to sit in. We
recommend that
installers use either a 4”
octagon box or an at
least 1“ deep single gang
outlet box.
1
OFF
ON
Hardwire installation
2
Connect the ground wire from back of the
mounng plate to the juncon box.
Install the square mounng plate onto the
juncon box using the two provide screws.
*Use the rectangular plate if you have a handy box.
Using the provided twist-on connectors,
connect the black (L) and white (N) AC wires.
Insert the LED driver unit half way into
the juncon box.
Slide the cover plate onto the mounng arms.
3
v.02102020
Using the provided screws,
install the mounng arms
as illustrated.
4
*Use rectangular cover
plate with handy box
5
Slide the lamp body onto the mounng arms.
7
Insert the lamp into the body.
6
Connect the +posive (RED)
and the -negave (BLACK)
wires from the LED driver to
the +posive and -negave
wiring terminals on the lamp
accordingly.
Using the provided hex key,
screw in the two lock
screws on both sides.
Rotate the LED light bar to
direct the light as you wish.
8
Warnings
Specificaons
Model ZBW
Temperature 3000 K
Brightness Adjustability Compable with ELV dimmers
Light Color So White
Overheang may result in reduced LED lifespan.
• Keep out of direct sunlight.
• Remove plasc bag from lamp before use.
• Recommended ambient temperature: under 77 °F.
Koncept Inc.
429 E. Huntington Drive
Monrovia, CA 91016, USA
Phone: [phone]
Fax: [phone]
[e-mail]
To reduce the risk of fire, electric shock or injury:
• Do not use near water
• Do not handle plug or appliance with wet hands
• Do not stare directly at LEDs
www.koncept.com
Register your Koncept LED lamp online and receive:
• One Year Warranty Extension
• Priority Product Servicing
Visit www.koncept.com/productsupport and enter your serial number
(S/N: XXXXXXXX) located on your product.
Koncept warrants to the original purchaser of this product against manufacturer defects in design, assembly,
material, or workmanship, and will, at Koncept’s opon, replace or repair any defecve product free of charge.
This coverage is valid for five years from the date of purchase as long as the original purchaser owns the product.
In the case of a hardwired product, this warranty is valid for one year for the LED driver specifically. Koncept will
replace or repair the product, which Koncept, at its sole discreon, agrees is defecve, free of charge provided
that the following condions for a return are fulfilled.
This warranty does not apply to any product damaged by accident, physical or electrical misuse or abuse,
improper installaon, alteraon, any use contrary to its intended funcon, war, fire, flood, or any other acts of
nature, or unauthorized repair.
Koncept assumes no liability for any events such as fines arising out of the use of this product or any
consequenal damages caused by any failure of the product to funcon properly. In no event shall Koncept be
liable for more than the replacement of the product. This warranty does not cover shipping or labor costs
associated with the replacement of a defecve product. Under no circumstances should this warranty or the
product covered by it be construed as an insurance policy against loss of any kind. Koncept staff neither assumes
nor authorizes any person or organizaon to make any warranes or assume any liability in connecon with the
sale or use of this product.
This warranty covers only products used in the territory covered by your local distributor. This is the complete
product warranty and no other warranty exists. Some jurisdicons may not allow limitaons on how long an
implied warranty lasts, or the exclusion or limitaon of incidental or consequenal damages, so the above
exclusions or limitaons may not apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary in different states and countries.
To file a replacement/repair claim under the warranty:
1) Contact Koncept for a return authorizaon number during the warranty period. A claim will not be accepted
without a return authorizaon number.
2) Provide a copy of the original purchase receipt with purchase date and product name clearly shown.
3) Return the defecve product to Koncept freight prepaid and accompanied by (1), (2), and (3) to the following
address: Limited Product Warranty
Koncept Inc. 429 E. Hunngton Drive, Monrovia, CA 91016
Limited Product Warranty
US & Canada:120 V ONLY