User's Manual
Table Of Contents
- Declare
- Important Safety Instructions
- Chapter 1 Function Chracteristic
- Chapter 2 Preparation
- 2.1 Unpacking & Checking
- 2.2 Dismantling Protective Materials
- 2.3 Parts Identification
- 2.4 Installing the Printer
- 2.5 Installing the Ribbon Cartridge
- 2.6 Installing and Dismantling the Right and Left Holders
- 2.7 Installing and Dismantling the Front Table
- 2.8 Installing the Tractor
- 2.9 Connecting to the Printer
- 2.10 Connecting to the Power Source
- 2.11 Installing Driver
- 2.12 Network Settings
- Chapter 3 Control Panel
- Chapter 4 Printer Setting
- Chapter 5 Menu Function Description
- 5.1 Emulation
- 5.2 Print Mode
- 5.3 Font Select
- 5.4 Compress Printing
- 5.5 Characters Pitch
- 5.6 Chinese Pitch
- 5.7 Line Feed Pitch
- 5.8 Top of Form Adjustment
- 5.9 Page Length Tractor
- 5.10 Page Length Manual
- 5.11 Page Width Detect Right
- 5.12 Page Width Detect Left
- 5.13 Top Margin
- 5.14 Bottom Margin
- 5.15 Left Margin
- 5.16 Text Direction
- 5.17 Graph Direction
- 5.18 Zero Style
- 5.19 Character Table EPSON
- 5.20 Character Table IBM
- 5.21 International Font
- 5.22 Code Page
- 5.23 AGM Mode
- 5.24 Paper Skew Detection
- 5.25 Jam Detection
- 5.26 Manual Eject the Paper
- 5.27 Language
- 5.28 Quiet Mode
- 5.29 Carriage Return Setting
- 5.30 Line Feed Setting
- 5.31 Tear off Function
- 5.32 Load Paper
- 5.33 Cover Detection
- 5.34 Baud Rate
- 5.35 Parity Bit
- 5.36 Data Length
- 5.37 Stop Bit
- 5.38 Protocol
- Chapter 6 Troubleshooting
- Chapter 7 Printer Specification
- Appendix A Self-test and Adjustment
ACCEL-7450 User's Manual
- 5 -
Note: 1. When your print becomes faint, you need to replace the ribbon cartridge. Otherwise, the
print quality will be affected and the print head may be damage.
2. To remove the old ribbon cartridge, first make sure the power is turned off, move the print
head to the left of the printer. Then pull out the ribbon nip, hold the ribbon cartridge
handle on both sides and lift it out of the printer forwards. Install a new one as the above
steps.
3. Never remove the print head when printer is on, or else the printer may get damaged.
Besides, do not touch the print head at the time finishes using the printer for overheating.
4. Please use the original JMR106 ribbon cartridge, our company will not guarantee to keep
the printer in good repair, when it is damaged by unauthorized ribbon cartridge.
2.6 Installing and Dismantling the Right and Left Holders
2.6.1 Installing the right and left holders
When installing the holder, firstly, aim the down install groove of the holder at the corresponding
positioning shaft on the printer, then rotate it upwards and make the upper install groove install into
place. (As shown below)
2.6.2 Dismantling the right and left holders
When dismantling the holder, firstly, pull the draw knob upwards then press the holder downwards,
the holder will be dismantled. (As shown below)
Figure 2-9 Install the right front table holder
Figure 2-8 Install the ribbon cartridge
Ribbon cartridge
Right front table holder