User's Manual
Table Of Contents
- Declare
- Important Safety Instructions
- Chapter 1 Function Chracteristic
- Chapter 2 Preparation
- 2.1 Unpacking & Checking
- 2.2 Dismantling Protective Materials
- 2.3 Parts Identification
- 2.4 Installing the Printer
- 2.5 Installing the Ribbon Cartridge
- 2.6 Installing and Dismantling the Right and Left Holders
- 2.7 Installing and Dismantling the Front Table
- 2.8 Installing the Tractor
- 2.9 Connecting to the Printer
- 2.10 Connecting to the Power Source
- 2.11 Installing Driver
- 2.12 Network Settings
- Chapter 3 Control Panel
- Chapter 4 Printer Setting
- Chapter 5 Menu Function Description
- 5.1 Emulation
- 5.2 Print Mode
- 5.3 Font Select
- 5.4 Compress Printing
- 5.5 Characters Pitch
- 5.6 Chinese Pitch
- 5.7 Line Feed Pitch
- 5.8 Top of Form Adjustment
- 5.9 Page Length Tractor
- 5.10 Page Length Manual
- 5.11 Page Width Detect Right
- 5.12 Page Width Detect Left
- 5.13 Top Margin
- 5.14 Bottom Margin
- 5.15 Left Margin
- 5.16 Text Direction
- 5.17 Graph Direction
- 5.18 Zero Style
- 5.19 Character Table EPSON
- 5.20 Character Table IBM
- 5.21 International Font
- 5.22 Code Page
- 5.23 AGM Mode
- 5.24 Paper Skew Detection
- 5.25 Jam Detection
- 5.26 Manual Eject the Paper
- 5.27 Language
- 5.28 Quiet Mode
- 5.29 Carriage Return Setting
- 5.30 Line Feed Setting
- 5.31 Tear off Function
- 5.32 Load Paper
- 5.33 Cover Detection
- 5.34 Baud Rate
- 5.35 Parity Bit
- 5.36 Data Length
- 5.37 Stop Bit
- 5.38 Protocol
- Chapter 6 Troubleshooting
- Chapter 7 Printer Specification
- Appendix A Self-test and Adjustment
ACCEL-7450 User's Manual
- 9 -
2.10 Connecting to the Power Source
1. As shown in Figure 2-19. Make sure the printer is turned off. (The pressed down side of the
power switch with “O” marks denotes the printer is off.)
2. Make sure the voltage required by the printer matches that of your electrical outlet.
3. If the power cord is attached to the printer, connect it to the AC inlet on the printer.
4. Plug the power cord into a properly grounded electrical outlet.
To turn the printer ON, press the I mark at the side of the power switch.
To turn the printer OFF, press the O mark at the side of the power switch.
Caution: 1. If the rated voltage doesn’t match the outlet voltage, contact your dealer for
assistance. Do not plug in the power cord.
2. Use the electrical outlet connecting the ground properly.
Note: After turn off the printer, you should wait more than 3 seconds before you restart the printer.
Or it may lead to initialization error.
2.11 Installing Driver
Please use the cable to connect computer with printer, then turn on the computer and the printer, put
the driver CD into the CD-ROM. Install driver by the following way:
2.11.1 Auto-install way
Double click the file “Setup.exe” in the driver disc, install driver by the following direction.
Note: The auto-install way just runs in the operation system of Windows 2000 or above.
Figure 2-19 Connect the power cord to the printer
Power switch
Power supply inlet
Electrical outlet
Power cord
Serial interface
Serial cable
Screw
Figure 2-18 Connect to the serial interface (25 -pin)