User's Manual

RADius 1000 Installation Manual, rev. 5 Appendix C - Bulgin connector assembly
47
APPENDIX D - TRANSPONDER ID SETTINGS
The table below shows the possible DIP switch settings for setting the TID on the RADius
Transponders. Standard settings are 150, 160, 170 … up to 300. Note that the battery powered
RADius 500 Low Power Transponders has two jumpers close to the middle of the card that
has to be shifted from lower to upper position when the frequency identities is 210 or higher
(marked with different colour in the table).
Switch Setting TID
MSB LSB
0 0 0 0 0 0 0 150
0 0 0 0 0 0 1 152
0 0 0 0 0 1 0 154
0 0 0 0 0 1 1 156
0 0 0 0 1 0 0 158
0 0 0 0 1 0 1 160
0 0 0 0 1 1 0 162
0 0 0 0 1 1 1 164
0 0 0 1 0 0 0 166
0 0 0 1 0 0 1 168
0 0 0 1 0 1 0 170
0 0 0 1 0 1 1 172
0 0 0 1 1 0 0 174
0 0 0 1 1 0 1 176
0 0 0 1 1 1 0 178
0 0 0 1 1 1 1 180
0 0 1 0 0 0 0 182
0 0 1 0 0 0 1 184
0 0 1 0 0 1 0 186
0 0 1 0 0 1 1 188
0 0 1 0 1 0 0 190
0 0 1 0 1 0 1 192
0 0 1 0 1 1 0 194
0 0 1 0 1 1 1 196
0 0 1 1 0 0 0 198
0 0 1 1 0 0 1 200
0 0 1 1 0 1 0 202
0 0 1 1 0 1 1 204
0 0 1 1 1 0 0 206
0 0 1 1 1 0 1 208
0 0 1 1 1 1 0 210
0 0 1 1 1 1 1 212
0 1 0 0 0 0 0 214
0 1 0 0 0 0 1 216
0 1 0 0 0 1 0 218
0 1 0 0 0 1 1 220
0 1 0 0 1 0 0 222
0 1 0 0 1 0 1 224
0 1 0 0 1 1 0 226
Switch Setting TID
MSB LSB
0 1 0 0 1 1 1 228
0 1 0 1 0 0 0 230
0 1 0 1 0 0 1 232
0 1 0 1 0 1 0 234
0 1 0 1 0 1 1 236
0 1 0 1 1 0 0 238
0 1 0 1 1 0 1 240
0 1 0 1 1 1 0 242
0 1 0 1 1 1 1 244
0 1 1 0 0 0 0 246
0 1 1 0 0 0 1 248
0 1 1 0 0 1 0 250
0 1 1 0 0 1 1 252
0 1 1 0 1 0 0 254
0 1 1 0 1 0 1 256
0 1 1 0 1 1 0 258
0 1 1 0 1 1 1 260
0 1 1 1 0 0 0 262
0 1 1 1 0 0 1 264
0 1 1 1 0 1 0 266
0 1 1 1 0 1 1 268
0 1 1 1 1 0 0 270
0 1 1 1 1 0 1 272
0 1 1 1 1 1 0 274
0 1 1 1 1 1 1 276
1 0 0 0 0 0 0 278
1 0 0 0 0 0 1 280
1 0 0 0 0 1 0 282
1 0 0 0 0 1 1 284
1 0 0 0 1 0 0 286
1 0 0 0 1 0 1 288
1 0 0 0 1 1 0 290
1 0 0 0 1 1 1 292
1 0 0 1 0 0 0 294
1 0 0 1 0 0 1 296
1 0 0 1 0 1 0 298
1 0 0 1 0 1 1 300