E INSTRUCTION MANUAL 9222-2733-11 MS-A406/0406/109678
Before you begin Thank you for purchasing this digital camera. Please take the time to read through this instruction manual so you can enjoy all the features of your new camera. Check the packing list before using this product. If any items are missing, immediately contact your camera dealer.
For proper and safe use Read and understand all warnings and cautions before using this product. WARNING Using batteries improperly can cause them to leak harmful solutions, overheat, or explode which may damage property or cause personal injury. Do not ignore the following warnings. • Only use the batteries specified in this instruction manual. • Do not install the batteries with the polarity (+/–) reversed. • Do not use batteries which show wear or damage.
• Use only the specified AC adapter within the voltage range indicated on the adapter unit. An inappropriate adapter or current may cause damage or injury through fire or electric shock. • Do not disassemble this product. Electric shock may cause injury if a high voltage circuit inside the product is touched. • Immediately remove the batteries or unplug the AC adapter and discontinue use if the camera is dropped or subjected to an impact in which the interior, especially the flash unit, is exposed.
CAUTION • Do not point the lens directly at the sun, a fire may result. Replace the lens cap when the camera is not in use. • Do not use or store the product in a hot or humid environment such as the glove compartment or trunk of a car. It may damage the product and batteries which may result in burns or injuries caused by heat, fire, explosion, or leaking battery fluid. • If batteries are leaking, discontinue use of the product. • The lens retracts when the camera is turned off.
About this manual The basic operation of this camera is covered between pages 12 and 33. This section of the manual covers the camera parts, preparation of the camera for use, and the basic camera operation for recording, viewing, and deleting images. Many of the features of this camera are controlled with menus. The menu navigation sections concisely describe how to change menu settings. Descriptions of the settings immediately follow the navigation sections. Names of parts ................................
Basic playback.....................................................................................................................................30 Single-frame playback and histogram display........................................................................30 Viewing and rotating images ...................................................................................................31 Deleting single images ...........................................................................................
A short guide to photography..............................................................................................................68 Advanced playback..............................................................................................................................70 Playing back movies ...............................................................................................................70 Capturing a movie frame....................................................................
Data-transfer mode..............................................................................................................................97 System requirements ..............................................................................................................97 Connecting the camera to a computer ...................................................................................98 Connecting to Windows 98 and 98SE ............................................................................
Names of parts * This camera is a sophisticated optical instrument. Care should be taken to keep these surfaces clean. Please read the care and storage instructions in the back of this manual (p. 116). Shutter-release button Flash (p. 26) Speaker Microphone Strap eyelet (p. 12) USB / AV / DC terminal cover Lens* Self-timer lamp (p. 47) The battery-chamber door (p. 13) and tripod socket are located on the bottom of the body.
Accessory shoe (p. 43) Exposure-mode dial (p. 21, 29, 36 - 40) Diopter-adjustment dial (p. 17) Macro button (p. 35) Flash-mode button (p. 26) Viewfinder* (p. 17) Zoom lever (p. 20) LCD monitor* Controller Access lamp Main switch Mode switch Menu button Quick View / Delete button (p. 30, 31) Information button (p.
GETTING UP AND RUNNING Attaching the strap and lens cap Always keep the strap around your neck in the event that the camera is accidentally dropped. An optional leather neck strap, NS-DG1000, is also available from your Konica Minolta dealer. Availability varies with region. 2 Pass one of the small loops of the lens-cap strap through the eyelet on the lens cap (1). Pass the other loop through the first loop and tighten (2).
Inserting batteries This digital camera uses four AA-size alkaline or Ni-MH batteries. Do not use other types of AA batteries. The camera should be off when replacing batteries. 2 To open the battery-chamber door, slide the door toward the side of the camera (1) to release the safety catch. Lift the door to open (2). 1 Insert the batteries as indicated on the diagram on the inside of the battery-chamber door. Confirm the positive and negative battery terminals are oriented correctly.
Battery condition indicator This camera is equipped with an automatic battery-condition indicator. When the camera is on, the battery-condition indicator appears on the monitor. If the monitor is blank, the batteries may be exhausted or installed incorrectly. Full-battery indicator - the battery is fully charged. This indicator is displayed for three seconds on the monitor when the camera is turned on. Low-battery indicator - battery power is low. The battery should be replaced as soon as possible.
Connecting the optional AC adapter Always turn off the camera before changing between power supplies. The AC Adapter allows the camera to be powered from an electrical household outlet. The AC Adapter is recommended when the camera is interfaced with a computer or during periods of heavy use. AC Adapter model AC-1L is for use in North America and Japan, and AC-11 is for use in all other areas. Insert the mini plug of the AC adapter into the DC terminal (1).
Changing the memory card An SD Memory Card or MultiMediaCard must be inserted for the camera to operate. If a card has not been inserted, a no-card warning is displayed on the monitor. For more about memory cards see page 118. Always turn off the camera and confirm the access lamp is not lit before removing a memory card; damage and data loss may result. 1 2 3 4 1. Open the card-slot door on the bottom of the camera. 2.
Turning on the camera and displays Press the main switch to turn the camera on. Pressing the switch again turns the camera off. When the camera is turned on, the Anti-shake indicator appears on the LCD monitor. Around the main switch is the mode switch. This switch is used to change between the recording and playback modes as well as the selecting the between the monitor and viewfinder display.
Setting the date and time After initially inserting a memory card and batteries, the camera’s clock and calendar must be set. When images are recorded, the image data is saved with the date and time of recording. 1 If the clock and calendar have not been set, a message is displayed for a few seconds each time the camera is turned on. This message is also displayed if the clock and calendar reset when the camera is stored without batteries for a long period.
Setting the Menu language For customers in certain areas, the menu language may have to be set. Press the menu button (1) to open the menu; the appearance of the menu will depend on the position of the camera’s controls. 2 Navigating the menu is simple. The up/down and left/right keys of the controller (2) move the cursor and change settings on the menu. The central button of the controller selects menu options and sets adjustments.
BASIC RECORDING This section covers the basic operation of this camera. Thoroughly familiarize yourself with the operations in this section before moving on to the other sections in the manual. Turn on the camera. Set the mode switch to a recording position. Handling the camera While using the viewfinder or LCD monitor, grip the camera firmly with your right hand while supporting the body with your left. Keep your elbows at your side and your feet shoulder-width apart to hold the camera steadily.
Recording images automatically Turn the exposure-mode dial to the auto-recording position (1); all camera operations are now fully automatic. The autofocus, exposure, and imaging systems will work together to bring beautiful results effortlessly. While many of the camera’s systems in this mode are automatic, some of the functions can be changed. The following list shows changes that can be made in auto-recording.
Basic recording operation The example uses auto recording. Except for movie recording, the operation for other exposure modes is the same. Automatic Digital Subject Program Selection is only available in the auto recording mode. Place the subject anywhere within the focus frame. Make sure the subject is within the focus range of the lens (p. 24). For very close subjects, use the macro function (p. 35). Press the shutter-release button partway down to lock the focus and exposure.
Automatic Digital Subject Program Selection Automatic Digital Program Selection chooses between program autoexposure and one of four digital subject programs. The digital subject programs optimize camera setting for various conditions and subjects. Automatic Digital Subject Program Selection is only available in auto recording and can be disabled in the auto-recording menu. For information on individual subject programs, see page 29.
Focus lock Focus lock prevents the AF system from focusing. This can be used with off-center subjects or when a special focusing situation prevents the camera from focusing (p. 25). Place the subject within the focus frame. Press and hold the shutter-release button partway down. • The focus signal indicates the focus is locked. The shutter speed and aperture value change from white to black indicating the exposure is locked.
Focus signals The focus signal in the lower right corner of the LCD monitor indicates the focus status. The shutter can be released even if the camera cannot focus on the subject. Focus locked. Focus confirmed (P, A, S, and M continuous AF focus mode and sports action digital subject program). Exposure continuously adjusts. Cannot focus. The subject is too close or a special situation is preventing the AF system from focusing.
Flash modes 1 To use the built-in flash, simply raise it (1). Lower the flash unit to prevent it from firing. Flash-mode indicator turns red while the flash is charging; wait until it becomes white before taking pictures. To change the flash mode, simply press the flash mode button (2) until the appropriate mode is indicated. 2 Autoflash - the flash fires automatically in low-light and backlit conditions.
Flash range - auto-recording mode The camera controls the flash output automatically. For well-exposed images, the subject must be within the flash range. Distance is given from the front of the lens. Because of the optical system, the flash range is not the same at the lens’ wide-angle position as it is at the telephoto position. Wide-angle position 0.2 - 4.0m (0.7 - 13.1 ft.) Telephoto position 1.2 - 2.5m (3.9 - 8.2 ft.
i+ button Pressing the information (i+) button changes the monitor display. The display cycles among the standard display, real-time histogram, and live image only. Standard display Real-time histogram Live image only The real-time histogram shows the approximate luminance distribution of the live image. This histogram cannot show the affect of flash illumination. The histogram of a recorded image may not show the same distribution as the real-time histogram.
Digital subject programs Digital subject programs optimize the camera’s exposure, white-balance, and imageprocessing systems for specific conditions and subjects. Simply turn the exposure mode dial to select the appropriate subject program; the active subject program is displayed in the bottom left corner of the monitor. Exposure-mode indicator Portrait - optimized to reproduce warm, soft skin tones and a slight defocusing of the background.
BASIC PLAYBACK Images can be viewed in the Quick View or playback modes. This section covers the basic operations in both modes. The playback mode has additional functions, see page 70. To view images from the playback mode, turn the mode switch to the playback position (1). 1 2 To view images from the recording mode, press the Quick View / delete button (2). Single-frame playback and histogram display Mode indicator Magnification (p. 33) Image size (p. 54) Image quality (p.
The histogram shows the luminance distribution of the image from black (left) to white (right). The 256 vertical lines indicates the relative proportion of that light value in the image. The histogram can be used to evaluate exposure, but displays no color information. Viewing and rotating images In Quick View or the playback mode, use the left/right keys of the controller to scroll through the images.
i+ button The information (i+) button controls the display format. Each time the button is pressed, the display cycles through to the next format: full display, image only, index playback. Full display Image only Index playback Information button In index playback, the four-way keys of the controller will move the yellow border. When the image is highlighted with the border, the date of recording, the lock and printing status, and the frame number of the image are displayed at the bottom of the screen.
Enlarged playback In single-frame playback in Quick View or the playback mode, a still image can be enlarged for closer examination from 1.2X. The maximum magnification depends on image size from 2X for 640x480 size images to 6X for 2272x1704 images. With the image to be magnified displayed, slide the zoom lever to the right (T) to activate the enlarged playback mode. The degree of magnification is displayed on the LCD monitor. Slide the zoom lever to the right (T) to increase the image magnification.
ADVANCED RECORDING This section cover the advanced recording features of this camera. Read the basic recording section before moving on to this section. Recording mode display 1 26 25 24 2 23 3 6 A 4 22 5 21 20 7 8 B 9 19 10 18 11 12 13 14 15 16 17 A. Focus frame B. Spot metering area (p. 61) 34 Advanced recording 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. Wide-angle converter indicator (p.
Macro Two macro modes are available: Super Macro and standard macro. Super Macro allows the camera to focus as close as 1cm (0.4 in.) from the front of the lens. When Super Macro is selected, the lens automatically zooms to a specific focallength position and cannot be changed. Standard macro allows the zoom to be used. The minimum focus distance changes with focal length, see below. Super-macro indicator Press the macro button (1) to select the macro mode.
Program (P) Exposure mode The program exposure mode controls both the shutter speed and aperture to ensure correct exposures. This exposure mode allows photographers to shoot without worry about exposure settings. The shutter speed and aperture values of the exposure are displayed on the monitor when the shutter-release button is pressed partway down. If shutter speed and aperture displays turn red, the scene is beyond the exposure control range of the camera.
Shutter priority (S) Exposure mode The photographer selects the shutter speed and the camera sets the appropriate aperture to ensure correct exposure. When shutter priority is selected, the shutter speed on the monitor turns blue and a double arrow indicator appears next to it. The shutter speed can be set between 1/1000 and 15 seconds. If the shutter speed is beyond the aperture range, the aperture display will turn red.
Manual (M) Exposure mode Manual exposure mode allows individual selection of shutter speeds and apertures. This mode overrides the exposure system giving the photographer total control over the final exposure. Use the up/down keys of the controller to change the shutter speed. Use the left/right keys of the controller to change the aperture. The changes made to the exposure will be visible in the live image on the monitor.
Time exposures Time photographs can be taken in the manual-exposure mode. Exposures up to thirty seconds can be made. The use of a tripod is recommended. The camera’s exposure system cannot be used to calculate time exposures. A separate light meter can be used to determine the exposure. 1 Use the down key of the controller to decrease the shutter speed below 15 seconds until “T” is displayed. Set the aperture using the left/right keys of the controller.
Movie recording This camera can record digital video with sound. Total recording time varies with the image size and frame rate, see page 66. The optical and digital zoom, exposure compensation, and the macro modes can be used. Other changes can be made with the movie recording menu (p. 44). Frame rate Image size Quality Before recording, the frame counter shows the maximum time in seconds that can be recorded on the next movie clip.
Exposure compensation The camera exposure can be adjusted to make the final picture lighter or darker by as much as ±2Ev in 1/3 increments. Exposure compensation can only be used with Digital Subject Programs, the P, A, and S exposure modes. With Digital Subject Programs, exposure compensation is reset when the exposure-mode dial is moved to another position or the camera is turned off. In P, A, and S exposure modes, exposure compensation remains in effect until reset.
Focus area selection Individual focus areas can be selected when recording still images. With auto recording and Digital Subject Programs, focus area selection is reset when the exposure-mode dial is moved to another position or the camera is turned off. In P, A, S, and M exposure modes, the selected focus area remains active until reset. Press and hold the central button of the controller until the five spot focus areas are displayed.
Attaching an accessory flash To extend the versatility of the camera, an accessory flash unit (sold separately) can be used. Always remove the accessory flash when the camera is not in use, and replace the accessory-shoe cap to protect the contacts. Slide the accessory-shoe cap off as shown. Mount the flash unit on the accessory shoe by sliding it forward until it stops.
Navigating the recording menus The recording menu displayed varies with the position of the exposure-mode dial. There are four menus depending on if auto recording, movie recording, Digital Subject Programs, or the P,A,S, and M exposure modes are selected. Pressing the menu button (1) turns the menu on and off. The four-way keys of the controller (2) move the cursor in the menu. Pressing the central button of the controller enters a setting. Activate the menu with the menu button.
Drive mode Image size Quality Auto DSP Digital zoom Single 2272x1704 Standard On Off Auto-recording menu Drive mode Image size Quality Focus mode Digital zoom Single 2272x1704 Standard Autofocus Off Digital Subject Program menu PASM Drive mode Image size Quality White balance Key func. Focus mode Color mode Digital zoom Quality Frame rate White balance Movie mode Cont. AF NaturalColor Off 320x240 STD. 15fps Auto STD.
Drive modes The drive modes control the rate and method images are captured. The drive mode is set on all menus except the movie menu. With auto recording and Digital Subject Programs, the drive mode is reset to single-frame advance when the exposure-mode dial is moved to another position or the camera is turned off. In P, A, S, and M exposure modes, the drive mode remains in effect until changed. Refer to the following sections for descriptions of the drive modes.
Self-timer Used for self-portraits, the self-timer will delay the release of the shutter for approximately ten seconds after the shutter-release button is pressed. The self-timer is set on section 1 of the recording menus (p. 44). 1 2 With the camera on a tripod, compose the picture so the subject is within the focus frames. Press the shutterrelease button partway down to lock the exposure and focus (1). Press the shutter-release button all the way down to begin the countdown (2).
Using the Continuous-advance modes The continuous-advance drive modes allow a series of images to be captured while holding down the shutterrelease button. These drive modes are set in section 1 of the recording menus. Drive mode Image size Quality White balance Key func. Single Self-timer Continuous Progressive Bracketing Immediately after selecting the continuous option on the menu, a selection screen is displayed to select between standard and UHS continuous advance.
Continuous-advance notes CONTINUOUS ADVANCE The continuous-advance drive mode can capture images at a rate of approximately 2.5 fps with 2272x1704 images and 2.2 fps with images of other sizes. Focus and exposure is set for each image when the continuous-AF focus mode is used, but the rate of capture is reduced. When the red low-battery warning appears or the flash is used, the rate of capture is also reduced. The following chart lists the approximate maximum number of images that can be captured.
Using the progressive-capture modes The Progressive-Capture drive modes continuously record images while holding down the shutter-release button. When the shutter button is released, the images stored in the camera’s buffer memory are saved. These drive modes are set in section 1 of the recording menus. Immediately after selecting the progressive option on the menu, a selection screen is displayed to select between standard and UHS Progressive Capture.
Progressive-Capture notes The advantage of Progressive Capture over the continuous-advance drive mode is that it allows you to record events without the need to predict when the event will start. Simply hold the shutterrelease button down to start saving images, and when the action happens, release the shutter button to save the recorded series. The flash cannot be used. When the red low-battery warning is displayed, these drive modes cannot be used.
Bracketing This mode makes a three-image bracket of a scene. Bracketing is a method of taking a series of images of a static subject in which each image has a slight variation in exposure. The bracketing mode is set in section 1 of the recording menus. Immediately after selecting the bracketing option on the menu, a selection screen is displayed to select the bracketing increment. Drive mode Image size Quality White balance Key func.
Number of frames in bracketing series The remaining number of frames in the bracket series is displayed on the monitor next to the bracketing indicator. If the memory is filled or the shutter button is released before the series has completed, the camera will reset and the entire bracket must be made again. The flash cannot be used with the bracketing drive mode. Frame counter The order of the bracket series is normal exposure, underexposure, and overexposure. The exposure bracket can be made in 0.3, 0.
Image size and image quality Changing image size affects the number of pixels in each image. The greater the image size, the larger the file size. Choose image size based on the final use of the image smaller images will be more suitable for web sites whereas larger sizes will produce higher quality prints. FINE STD. ECON. LCD monitor 2272 1600 1280 640 Number of pixels (hor. X vert.) 2272 X 1704 1600 X 1200 1280 X 960 640 X 480 Fine - high-quality JPEG image. Standard - the default setting.
Approximate file sizes Size Quality Fine Standard Economy 2272 X 1704 1600 X 1200 1280 X 960 640 X 480 2100KB 1050KB 570KB 1050KB 660KB 390KB 680KB 420KB 300KB 320KB 240KB 160KB Approximate number of images that can be stored on a 16MB memory card Fine Standard Economy 6 14 27 14 23 41 23 38 53 50 67 100 Camera Notes The frame counter indicates the approximate number of images that can be stored on the memory card at the camera’s image quality and size settings.
Auto DSP Automatic Digital Subject Program Selection can be temporarily disabled in the auto-recording menu. When disabled, the program exposure mode is active. If the camera is turned off, Automatic Digital Subject Program Selection is activated. Drive mode Image size Quality Auto DSP Digital zoom Single 2272x1704 Standard On Off Digital zoom The digital zoom is activated in all recording menus (p. 44). The digital zoom extends the power of the telephoto position of the optical zoom by up to 4X in 0.
Focus modes This camera has autofocus and manual focus control. The focus mode is selected separately in the Digital Subject Program, movie, and P, A, S, and M exposure-mode menus. When using Digital Subject Programs, the focus mode is reset when the camera is turned off. With the P, A, S, or M exposure modes or movie recording, the autofocus mode can be specified between single-shot AF and continuous AF in section 2 of the menu (p. 44).
White balance White balance is the camera’s ability to make different types of lighting appear neutral. The effect is similar to selecting daylight or tungsten film, or using color compensating filters in conventional photography. An indicator will be displayed on the monitor if a setting other than auto white-balance is chosen. White balance is set independently in section 1 of the movie, and P, A, S, and M exposure-mode menus (p. 44).
Custom White Balance Custom white-balance allows the camera to be calibrated to a specific lighting condition. The setting can be used repeatedly until reset. Custom white balance is especially useful with mixed-lighting or when critical control over color is needed. The object used to make a calibration must be neutral. A blank piece of white paper is an ideal surface and can easily be carried in a camera bag. To calibrate the camera, select custom setup (Cust.
Full-time AF With full-time AF active, the autofocus systems continually focuses to keep the monitor image sharp. This also reduces the autofocusing time when taking pictures. When the camera is set to manual focus, full-time AF is disabled. Turning the full-time AF function off can help conserve battery power. Full-time AF can be turned on and off in section 2 of the P, A, S, and M menus (p. 44).
Positive compensation No compensation Negative compensation No flash Flash compensation changes the ratio between the ambient and flash exposures. When using fillflash to reduce harsh shadows caused by direct sunlight, flash compensation changes the ratio between the highlights and shadows. The flash affects the darkness of the shadows without affecting the area illuminated by the sun.
Camera sensitivity - ISO Five camera sensitivity settings can be selected: Auto, 50, 100, 200, and 400; the numerical values are based on an ISO equivalent. ISO is the standard used to indicate film sensitivity: the higher the number, the more sensitive the film. Camera sensitivity is set in section 3 of the P, A, S, and M menus (p. 44).
Color Mode The color mode controls whether a still image is color or black and white. This must be set before the image is recorded. The color mode is set in section 3 of the P, A, S, and M menus and section 2 of the movie menu (p. 44). The live image reflects the selected color mode. The color mode has no effect on image file size. Vivid Color Black & White Sepia Natural Color reproduces the colors in the scene faithfully. This mode uses no monitor indicator when active.
Sharpness Sharpness accents or softens details in an image in three levels: hard (+), normal, and soft (–). This can be set in section 3 of the P, A, S, and M menus (p. 44). Any changes made are applied to the live image, but may be difficult to see. However, when viewed with a computer, the changes will be evident. If any level except normal is selected, an indicator appears on the monitor as a warning.
Custom key function The function assigned to the flash mode button can be selected among the flash mode, drive mode, white balance, focus mode, color mode, and camera sensitivity. This can be set in section 1 of the P, A, S, and M menus (p. 44). The flash mode can also be changed in section 2 of the P, A, S, and M menus. When the key-function option is selected and entered, a selection screen appears. Use the four-way key of the controller to select the function.
Quality (movie) Movies can be recorded at three size and quality combinations: 640x480 Fine, 640x480 Standard, and 320x240 Standard. Image size and quality are the same as those for still images: the larger the image size and higher the quality, the larger the file size. Image size is set in the movie menu (p. 44). Quality Frame rate White balance Movie mode 320x240 STD. 15fps Auto STD. movie Frame rate Movies can be recorded at two frame rates: 15 fps and 30 fps.
The performance of the memory card may prematurely end the recording of a movie clip. Test the card before important events. Check the Konica Minolta web site for the latest compatibility information: North America: http://www.konicaminolta.us/ Europe: http://www.konicaminoltasupport.com. Movie mode The movie mode option selects the type of movie recorded. Standard produces a normal movie clip.
A SHORT GUIDE TO PHOTOGRAPHY Photography can be a rewarding pursuit. It is a broad and disciplined field that can take years to master. But the pleasure in making photographs and the joy of capturing a magical moment cannot be compared. The guide is an introduction to some basic photographic principles. The lens aperture controls not only exposure, but also depth of field; the area between the closest object in focus and the furthest object in focus.
The shutter controls not only exposure, but also the ability to stop motion. Fast shutter speeds are used in sport photography to stop action. Slow shutter speeds can be used to show the flow of motion such as water cascading over a waterfall. The use of a tripod is recommended with slow shutter speeds. The change in aperture and shutter speed is not apparent in the live image. Unlike film cameras, test photographs can be taken and immediately viewed.
ADVANCED PLAYBACK The basic functions in this mode are described in the basic playback section on pages 30 through 33. This section covers how to playback movie clips as well as the advanced function on the playback menu. Movie clips can be played back in Quick View. Playing back movies Play Use the left/right keys of the controller to display the movie. Press the center of the controller to play back the movie clip.
Capturing a movie frame A single frame from a movie clip can be copied and saved as a still image. The copied image has the same image size as the original movie. During playback, press the center button of the controller to pause the movie playback at the point to capture the frame. When the movie is paused, the left/right keys can be used to jog the clip to display the correct frame. Pause Rew Fwd Vol Press the up key of the controller to capture the frame.
Navigating the playback menu Pressing the menu button (1) turns the menu on and off. The four-way keys of the controller (2) move the cursor in the menu. Pressing the central button of the controller enters a setting. Activate the menu with the menu button. Use the left/right keys of the controller to highlight the appropriate menu tab; the menu changes as the tabs are highlighted. Use the up/down keys to scroll through the menu options. Highlight the option whose setting needs to be changed.
Delete Format Lock Copy – – – – Slide show Playback Duration Repeat – – 5 sec. No DPOF set Date print Index print E-mail copy – Off – – To delete images on the memory card (p. 75). To format the memory card (p. 76). To protect images from deletion (p. 77). To copy images from one memory card to another (p. 78). To play back images automatically (p. 80). To select the images for the Slide Show (p. 80). To specify how long each image is played back (p. 80).
Frame-selection screen When a marked-frames setting is chosen on a menu, the frame selection screen will appear. This screen allows multiple images to be chosen. The left/right keys of the controller moves the yellow border to select the image. :move :sel. :enter The up key of the controller selects the frame; when selected, an indicator appears next to the image. The down key deselects the image removing the indicator. The garbage can indicates the image is selected for deletion.
Delete Deleting permanently erases the file. Once deleted, a file cannot be recovered. Care should be taken when deleting images. Single, multiple, or all files on the memory card can be deleted in section 1 of the playback menu (p. 72). The delete option has three settings: This frame Delete Format Lock Copy – – – – The file displayed or highlighted in the playback mode is deleted. All frames All unlocked files are deleted. Marked frames To delete multiple files.
Format When a memory card is formatted, all data on the card is erased. The formatting function is used to erase all data on a memory card. Before formatting a memory card, copy the data to a computer or storage device. Locking images will not protect them from being deleted when the card is formatted. Always format the memory card using the camera; never use a computer to format a card. When the format option is selected and entered in section 1 of the playback menu (p. 72), a confirmation screen appears.
Lock Single, multiple, or all files can be locked. A locked file cannot be deleted by either the playback menu functions or the QV/delete button. However, the formatting function (p. 76) will erase all files on a memory card whether locked or not. Important images should be locked. The lock function is in section 1 of the playback menu (p. 72). The lock option has four settings: This frame The file displayed or highlighted in the playback mode is locked.
Copy and E-mail copy The copy function in section 1 of the playback menu (p. 72) makes exact copies of image or movie files and can store the copied data on another memory card. E-mail Copy in menu section 3 makes a 640x480 (VGA) JPEG copy of an original still image so that it may be easily transmitted by e-mail. E-mail copies can only be copied to the original card.
Copy When the image(s) to be copied are selected, a screen with four messages is displayed. The messages are highlighted during the copying procedure. Copy Copying to camera memory. Change card. Copying to card. Copying completed. When the change-card message is highlighted, remove the camera’s memory card and insert the card to which the image should be copied. Press the central button of the controller to continue or the menu button to cancel the copy operation. :enter Copied to 101KM_CP.
Slide Show Section 2 of the playback menu controls the slide-show function. This function automatically displays all still images and movie clips on the memory card in order. The menu has the following options: Slide show Enter All frames To start the slide-show presentation. Highlight “Enter” and press the central button of the controller to start the slide show. To select all the images on the memory card to be displayed in the slide-show presentation.
The controller can be used to control the presentation during playback. Press the central button of the controller to pause and restart the slide show presentation. Slide show Playback Duration Repeat – – 5 sec. No The left/right keys advance to the next still image or return to the previous one. During a movie, the left/right keys forward or rewind the clip. The up/down keys adjust the volume. Press the menu button to cancel the presentation.
About DPOF This camera is supported by DPOF™ version 1.1. The DPOF (Digital Print Order Format) allows direct printing of still images from digital cameras. After the DPOF file is created, the memory card is simply taken to a photofinishing service or inserted into the memory-card slot of DPOF compatible printers. When a DPOF file is created, a misc. folder is automatically created on the memory card to store it (p. 102).
When the this-frame or all-frames setting is chosen, a screen appears requesting the number of copies of each image; a maximum of nine copies can be ordered. Use the up/down keys of the controller to set the required number of copies. If the all-frames setting was used to create a print order, any additional images recorded afterwards will not be included in the order. DPOF files created with another camera will be canceled.
Viewing images on a television It is possible to view camera images on your television. The camera has a video-out terminal to make the connection using the supplied AV cable. The camera is compatible with the NTSC and PAL standards. The video-output setting can be checked and set in section 4 of the setup menu (p. 86). 1. Turn off the television and the camera. 2. Insert the small plug of the AV cable into the camera’s AVout terminal. The arrow on the plug should face the back of the camera. 3.
SETUP MENU The setup menu is used to control the camera’s functions and operation. The navigating the setup menu section covers the operation of the menu. The section is followed by detailed descriptions of the settings. Opening the setup menu The setup menu is opened from the other menus. It can be accessed from any of the recording or playback menus.
Navigating the setup menu See page 85 on how to open the menu. The four-way keys of the controller (1) move the cursor in the menu. Pressing the central button of the controller enters a setting. Use the left/right keys of the controller to highlight the appropriate menu tab; the menu changes as the tabs are highlighted. Use the up/down keys to scroll through the menu options. Highlight the option whose setting needs to be changed.
LCDbrightness Power save Inst.Playback Lens acc. Language – 1 min. Off None English File # memory Folder name Noise reductn Date/Time set Date imprint Off Std. form On – Off Reset default Audio signals Focus signal Shutter FX Volume – 1 1 1 2 Video output Transfer mode Self-timer Anti-shake NTSC Data storage 10 sec. Disp. + Exp. To set monitor brightness (p. 88). To set the auto power save period (p. 88). To play back a still image after it is recorded (p. 88).
LCD Monitor Brightness Monitor brightness can be adjusted in 11 levels. Brightness can be set individually for viewfinder and direct viewing in the recording mode. Turn the mode switch to the appropriate position before opening the brightness option in section 1 of the setup menu (p. 86). Also see page 28. Set LCD brightness Low High Use the left/right keys of the controller to adjust brightness, the monitor image changes accordingly. Press the central button of the controller to set the level.
Camera Notes Single still images can be previewed immediately after being captured without instant playback active. Simply continue to hold the shutter-release button down after taking the picture to display the image. Release the shutter button to end the playback. Lens accessory This camera is compatible with the optional Wide-Angle Converter ZCW-300 Kit. This kit contains a 0.
Folder name All recorded images are stored in folders on the memory card. Two folder-name formats are available in section 2 of the setup menu, standard and date. Standard folders have an eight character name. The initial folder is named 100KM006. The first three digits are the folder’s serial number, which will increase by one each time a new folder is created. The next two letters refer to Konica Minolta, and the last three numbers indicate the camera used; 006 indicates a DiMAGE Z3.
Date and time setup It is important to accurately set the clock. When a still image or a movie clip is recorded, the date and time of the recording are saved with the image and are displayed during playback or can be read with the supplied DiMAGE Viewer software. The date format that is displayed or imprinted can be changed: YYYY/MM/DD (year, month, day), MM/DD/YYYY (month, day, year), DD/MM/YYYY (day, month, year). See page 18 for instructions on how to set the clock and calendar.
Reset default This function affects all modes. When selected, a confirmation screen appears; choosing “Yes” resets the following functions and settings, “No” cancels the operation.
Playback menu Playback (Slide Show) Duration (Slide Show) Repeat (Slide Show) Date print Index print Setup menu LCD Brightness Auto-power-save period Instant playback Lens accessory File number (#) memory Folder name Noise reduction Date imprinting Audio signals Focus signals Shutter FX Volume Transfer mode Self-timer Anti-shake All frames 5 seconds No Off No p. p. p. p. p. 80 80 80 83 83 Normal 1 minute Off None Off Standard On Off 1 1 1 2 Data storage 10 seconds Standard p. p. p. p. p. p. p. p. p. p.
Focus signal When the shutter-release button is pressed partway down, an audio signal confirms the AF system has focused. The focus signals can be changed or turned off in section 3 of the setup menu (p. 86). Two tones are available. Reset default Audio signals Focus signal Shutter FX Volume – 1 1 1 2 Shutter FX When the shutter is released, a shutter sound effect gives a positive confirmation a still image is recorded. The sound effect can be turn off in section 3 of the setup menu (p. 86).
Transfer mode The data-transfer mode must be specified depending on whether images are transferred to a computer or printed directly. The data-storage option must be selected to transfer data from the camera to a computer or when using the DiMAGE Viewer software. The PictBridge option allows images to be printed directly from the camera with a PictBridge compatible printer (p. 108). Self-timer Self-timer delay period can be selected between 10 seconds and 2 seconds in section 4 of the setup menu (p. 86).
Frame the subject as described in the basic operation section and press the shutter-release button partway down. Confirm the image has stabilized on the monitor and press the shutter-release button all the way down to take the picture. Three options are available for the Anti-shake system in section 4 of the setup menu (p. 86): Display + Exp. - when the shutter-release button is pressed partway down, the anti-shake function will activate. The affect of the Anti-shake system can be seen in the live image.
DATA-TRANSFER MODE Read this section carefully before connecting the camera to a computer. Instructions on using and installing the DiMAGE Viewer software are found in the supplied software manual. The DiMAGE manuals do not cover the basic operation of computers or their operating systems; please refer to the manual supplied with your computer.
Connecting the camera to a computer Confirm the battery has sufficient power before connecting the camera to a computer; the full-battery indicator should be displayed on the monitor. The use of the AC adapter (sold separately) is recommended over the use of the battery. For users with Windows 98 or 98 Second Edition, read the section on page 99 on how to install the necessary USB driver before connecting the camera to a computer. 1. Start up the computer.
When the USB connection is completed, a drive icon, or volume, appears in My Computer or the desktop; the name varies with memory card. When using Windows XP or Mac OS X, a window opens requesting instructions on what to do with the image data; follow the directions in the window. Mac OS X Mac OS Windows XP Windows Connecting to Windows 98 and 98 SE The driver needs only to be installed once.
Manual Installation To install the Windows 98 driver manually, follow the instructions in the connecting-the-camera-to-a-computer section on page 98. When the camera is plugged into the computer, the operating system will detect the new device and the add-newhardware-wizard window opens. Place the DiMAGE Viewer CD-ROM in the CD-ROM drive. Click “Next.” Choose the recommended search for a suitable driver. Click “Next.” Choose to specify the location of the driver.
The add new hardware wizard will confirm the location of the driver. The letter designating the CD-ROM drive will vary between computers. Click “Next” to install the driver in the system. One of three drivers may be located: MNLVENUM.inf, USBPDR.inf, or USBSTRG.inf. The last window confirms the driver has been installed. Click “Finish” to close the add new hardware wizard. Restart the computer. When the my-computer window is opened, a new removable-disk icon is displayed.
Memory card folder organization Once the camera is connected to the computer, image files can be accessed by double clicking on icons. Image folders are located in the DCIM folder. The misc. folder contains DPOF print files (p. 82). Drive Icon Dcim Files and folders on the memory card can be deleted using the computer. Never format the memory card from the computer; always use the camera to format the card. Only files recorded by the camera should be stored on the memory card.
The number in the image file name may not correspond to the frame number of the image. As images are deleted in the camera, the frame counter will adjust itself to show the number of images on the card and reassign the frame numbers accordingly. The serial numbers used with image files will not change when an image is deleted. When a new image is recorded, it will be assigned a number one greater than the largest serial number in the folder.
Disconnecting the camera Never disconnect the camera when the access lamp is red - the data or memory card may permanently be damaged. Windows 98 / 98 Second Edition Confirm that the access lamp is not lit. Turn off the camera and then disconnect the USB cable. Windows Me, 2000 Professional, and XP To disconnect the camera, click once on the unplug-or-eject-hardware icon located on the task bar. A small window will open indicating the device to be stopped. Click on the small window to stop the device.
The hardware devices to be stopped will be displayed. Highlight the device by clicking on it then click “Stop.” A confirmation screen will appear to indicate the devices to be stopped. Clicking “OK” will stop the device. A third and final screen will appear to indicate the camera can be safely disconnected from the computer. Close the window, turn the camera off, and then disconnect the USB cable.
Changing the memory card Never remove the card when the access lamp is red - the data or memory card may permanently be damaged. Windows 98 and 98 Second Edition 1. Turn off the camera. 2. Change the memory card. 3. Turn on the camera to remake the USB connection. Windows Me, 2000 Professional, and XP 1. Stop the USB connection using the unplug-or-eject-hardware routine (p. 104). 2. Turn off the camera. 3. Change the memory card. 4. Turn on the camera to remake the USB connection. Macintosh 1.
Uninstalling the driver software - Windows 1. Insert a memory card in the camera and connect it to the computer with the USB cable. Other devices must not be connected to the computer during this procedure. 2. Right click on the My-computer icon. Select “properties” from the drop-down menu. Windows XP: from the start menu go to the control panel. Click on the performance and maintenance category. Click “System” to open the system properties window. 3.
PictBridge Confirm the transfer-mode option in section 4 of the setup menu is set to PictBridge. Connect the camera to a PictBridge compatible printer using the camera’s USB cable. The larger plug on the cable is connected to the printer. Open the AV out/ USB port cover and insert the smaller plug of the cable into the camera. Turn the camera on; the PictBridge screen is displayed automatically. Individual still images can be selected for printing on the PictBridge screen.
No. of prints: Print size: Layout: Print quality: Data print: :start 7 Printer setup Printer setup Printer setup Printer setup The number of prints in the print run are displayed as well as the print parameters selected with the menu. See the menu navigation section for more information (p. 110). Press the central button of the controller to begin printing, or press the menu button to return to the PictBridge screen. A maximum number of fifty images can be printed.
Navigating the PictBridge menu Pressing the menu button (1) turns the menu on and off. The four-way keys of the controller (2) move the cursor in the menu. Pressing the central button of the controller enters a setting. Activate the menu with the menu button. Use the left/right keys of the controller to highlight the appropriate menu tab; the menu changes as the tabs are highlighted. Use the up/down keys to scroll through the menu options. Highlight the option whose setting needs to be changed.
The options that can be changed vary with the printer. Batch print Index print – – Batch print Batch print in section 1 selects all still images on the memory card for printing. Two options are available: All-frames - to print all images on the card. A screen opens so the number of copies of each image can be specified. A maximum number of fifty images can be printed. Reset - to cancel changes made with the batch print option or with the print selection screen.
Paper size The paper size of the print can be specified. Highlight the current page size and press the central button of the controller to open paper-size screen. Use the controller to select the paper size, and press the central button to complete the operation. A paper size not available with the printer in use cannot be selected.
Data print Data can be printed with the image. The printer-setup option uses the options set with the printer. The date of capture and the file name can be selected for printing. Data printing can also be disabled with the menu. DPOF print DPOF print – No.
APPENDIX Troubleshooting The section covers minor problems with basic camera operation. For major problems or damage, or if a problem continues to reoccur frequently, contact a Konica Minolta service facility. Problem Symptom The camera will not work. Nothing displayed on the monitors. Shutter will not release. No-card warning appears on the monitors. Pictures are not sharp. 114 Appendix Focus signal is red. Cause Solution The batteries are dead. Replace batteries (p. 13).
Pictures are not sharp. Pictures are taken indoors or in low-light situations without flash. While using flash, the pictures are too dark. Slow shutter speeds result in blurred images when the camera is hand-held. Use a tripod, change the camera sensitivity to a higher setting (p. 62), or use the flash (p. 26). The subject is beyond the flash range (p. 62). Move closer to the subject or change the camera sensitivity to a higher setting (p. 62).
Care and storage Read this section in its entirety to get the best results from your camera. With proper care, your camera will provide years of service. Camera care • Do not subject the camera to shock or impact. • Turn off the camera when transporting. • This camera is neither waterproof nor splashproof. Inserting or removing batteries or the memory card, or operating the camera with wet hands may damage the camera. • When at the beach or near water, take care not to expose the camera to water or sand.
LCD monitor care • The LCD monitor is manufactured using high-precision technology and more than 99.99% of the pixels operate properly. Less than 0.01% of the monitor pixels are displayed as color or bright points; this is not monitor defect and does not affect the recorded image. • Do not apply pressure to the surface of the LCD monitor; it may be permanently damaged. • In cold temperatures, the LCD monitor may become temporarily dark. When the camera warms up, the display will function normally.
Memory cards SD Memory Cards and MultiMediaCards are manufactured with precision electronic components. The following may cause data loss or damage: • Improper use of the card. • Bending, dropping, or subjecting the card to impact. • Heat, moisture, and direct sunlight. • Static electrical discharge or electromagnetic fields near the card. • Removing the card or interrupting the power supply while the camera or a computer is accessing the card (reading, writing, formatting, etc.).
Before important events and journeys • Check the camera’s operation; take test pictures and purchase spare batteries. • Konica Minolta has no responsibility for any damage or loss incurred by equipment malfunction. Copyright • TV program, films, video tapes, photographs, and other materials may be copyrighted. Unauthorized recording or duplication of such material may be contrary to copyright laws. Taking pictures or images of performances, exhibitions, etc.
QuickTime system requirements IBM PC / AT Compatible Pentium processor-based PC or compatible computer Windows 98, Me, 2000, or XP. To install QuickTime, follow the instructions in the installer. Macintosh users can download the latest version of QuickTime free of charge from the Apple Computer web site: http://www.apple.com. 128MB or more of RAM Videoimpression 2 system requirements To install ArcSoft VideoImpression, follow the instructions in the installer. Windows 98SE, Me, 2000, or XP.
This mark on your camera certifies that this camera meets the requirements of the EU (European Union) concerning interference causing equipment regulations. CE stands for Conformité Européenne (European Conformity). FCC Compliance Statement Declaration on Conformity Responsible Party: Konica Minolta Photo Imaging U.S.A. Inc.
Technical specifications CCD: Number of effective pixels: Total number of pixels: Camera sensitivity (ISO): Aspect ratio: Lens construction: Maximum aperture: Focal length: Focusing range: Autofocusing system: Focus modes: Shutter: Shutter speeds: Built-in flash recycling time: Monitor LCD: Monitor field of view: Viewfinder field of view: A/D conversion: Recording media: File formats: 122 Appendix 1/2.5-type interline primary-color CCD 4.0 million 4.2 million Auto and 50, 100, 200, 400 ISO equivalents.
Printing output control: Menu languages: AV output: Batteries: Battery performance (recording): Battery performance (playback): Optional external power source: Dimensions: Weight: Operating temperature: Operating humidity: Exif print, PRINT Image Matching II, PictBridge Japanese, English, German, French, Spanish, and Simplified Chinese NTSC and PAL Four AA alkaline or Ni-MH batteries.
Konica Minolta Customer Support: www.konicaminoltasupport.com Konica Minolta Photoworld: www.konicaminoltaphotoworld.com Become a member of the Konica Minolta Photo World today. It is free for registered customers of Konica Minolta Werden Sie noch heute Mitglied der Konica Minolta Photo World. Die Mitgliedschaft ist für registrierte Konica Minolta-Kunden kostenlos! Devenez dès aujourd’hui, membre du Konica Minolta Photo World. L’inscription est gratuite. © 2004 Konica Minolta Photo Imaging, Inc.
