Contents 1 Introduction 1.1 1.1.1 1.2 1.3 2 Welcome .......................................................................................................................................... 1-2 Composition of User's Guide............................................................................................................. 1-2 Energy Star® ...................................................................................................................................
MEMO Contents-2 bizhub PRESS 1250/1052
1 Introduction
1 Welcome 1 Introduction 1.1 Welcome 1.1 Thank you for purchasing this machine. This User’s Guide provides precautions and requests that should be followed to ensure safe usage of this machine. Please be sure to read this guide before using the machine. 1.1.1 1-2 Composition of User's Guide Printed manuals Overview [User's Guide - Security] This guide describes the security functions.
1.1 1 Welcome User's guide CD manuals Overview [User's Guide - Network Scanner] This guide describes operations of the network scanner functions. • Saving on the HDD for main body/Outputting • Sending via e-mail • Saving on the HDD for controllers • Sending to FTP server • Sending to SMB server • Sending to group [Trademarks/Copyrights] This guide describes trademarks, licenses, and copyrights concerning this machine. Please be sure to refer to this guide before using the machine.
1 1.2 Energy Star® 1.2 Energy Star® The ENERGY STAR® Program has been established to encourage the widespread and voluntary use of energy efficient technologies that reduce energy consumption and prevent pollution. As an ENERGY STAR Partner, this product meets the ENERGY STAR guidelines for energy efficiency, based on the following features. Auto Low Power Auto Low Power conserves energy by lowering the power consumption.
1.3 1.3 Legal Restrictions on Copying 1 Legal Restrictions on Copying Certain types of original must never be copied with the purpose or intent to pass copies of such documents off as the originals. The following is not a complete list, but is meant to be used as a guide to responsible copying.
1 Legal Restrictions on Copying 1.
2 Precautions for Installation and Use
2 Safety Information 2 Precautions for Installation and Use 2.1 Safety Information 2.1 This section contains detailed instructions on the operation and maintenance of this machine. To achieve optimum utility of this device, all operators should carefully read and follow the instructions in this manual. Please read the following section before connecting the machine to the supply. It contains important information related to user safety and preventing equipment problems.
2.1 2.1.1 Safety Information 2 Disassemble and Modification Do not modify this product, as a fire, electrical shock, or breakdown could result. If the product employs a laser, the laser beam source could cause blindness. Do not attempt to remove the covers and panels which have been fixed to the product. Some products have a high-voltage part or a laser beam source inside that could cause an electrical shock or blindness. 2.1.2 Power Cord Use only the power cord supplied in the package.
2 2.1.4 Safety Information 2.1 Power Plug Do not unplug and plug in the power cord with a wet hand, as an electrical shock could result. Plug the power cord all the way into the power outlet. Failure to do this could result in a fire or electrical shock. Do not tug the power cord when unplugging. Pulling on the power cord could damage the cord, resulting in a fire or electrical shock. Remove the power plug from the outlet more than one time a year and clean the area between the plug terminals.
2.1 Safety Information 2 After installing this product, mount it on a secure base. If the unit moves or falls, it may cause personal injury. Do not place the product in a dusty place, or a site exposed to soot or steam, near a kitchen table, bath, or a humidifier. A fire, electrical shock, or breakdown could result. Do not place this product on an unstable or tilted bench, or in a location subject to a lot of vibration and shock. It could drop or fall, causing personal injury or mechanical breakdown.
2 2.1.9 Safety Information 2.1 Consumables Do not throw the toner bottle or toner into an open flame. The hot toner may scatter and cause burns or other damage. Do not leave toner-related parts (toner bottles or drum units) within easy reach of children. Licking any of these parts or ingesting toner could damage your health. Do not store toner-related parts (developing units) near devices susceptible to magnetism, such as precision equipment and data storage devices.
2.1 2.1.12 Safety Information 2 Before Successive Holidays Unplug the product when you will not use the product for long periods of time. 2.1.13 Paper Do not use stapled paper, conductive paper (such as silver paper or carbon paper) or treated heat-sensitive/inkjet paper, otherwise a fire may result. 2.1.14 Paste Pellet Do not put paste pellets close to fire. Paste pellets are flammable and easy to catch on fire. Do not swallow paste pellets.
2 Regulation Notices 2.2 Regulation Notices 2.2.1 Ozone Release 2.2 During print operation, a small quantity of ozone is released. This amount is not large enough to harm anyone adversely. However, be sure the room where the machine is being used has adequate ventilation, especially if you are printing a high volume of materials, or if the machine is being used continuously over a long period. 2.2.
2.2 Regulation Notices 2 energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
2 2.3 Warning and Caution Labels 2.3 Warning and Caution Labels This machine has warning label, caution labels and indicators for safety precaution in the following location. These labels and indicators advise you to pay special attention to avoid any dangerous situations or serious injury when you replace the units. 7 CAUTION DO NOT remove warning or caution labels! Should any warning or caution label be removed, you may fail to check a specific part to be alert for unexpected trouble or injury.
2.3 2.3.2 Warning and Caution Labels 2 Caution Labels on Fixing Conveyance Unit 7 CAUTION DO NOT put your hand or arm between the main body and the fixing conveyance unit. Touching connecting terminals of electric parts may damage the machine or cause unexpected trouble. Please do not try to work yourself, but contact your service representative.
2 2.3.3 Warning and Caution Labels 2.3 Caution Label on Hinges of ADF 7 CAUTION DO NOT insert your fingers into the two ADF hinge portions. Otherwise, you may be injured. Please be careful when opening or closing the ADF. 2.3.4 Caution Label on Waste Toner Box 7 WARNING NEVER throw the waste toner box into a fire. Otherwise, the toner may ignite and cause a dangerous situation.
2.3 2.3.5 Warning and Caution Labels 2 Caution Label on Perfect Binder PB-503 7 CAUTION DO NOT touch the paste tank unit. Otherwise, you may get burned. Please be especially careful if you push the paste tank unit backward in place.
2 2.3.6 Warning and Caution Labels 2.3 Caution Labels on Finisher FS-532 7 CAUTION DO NOT put your hand on the top of printed sheets when removing them from the primary (main) tray. Failure to do so may cause unexpected injury, such as getting your fingers squeezed between the main body and the primary (main) tray going upward. Be sure to hold both front and rear sides of the stack to remove it from the tray.
2.3 Warning and Caution Labels 2 7 CAUTION DO NOT put your hand into the hollow portion inside the finisher. The finisher mounted with Punch Kit PK-522 has a hollow portion, in the back of which is located a motor. Touching the motor, you may get burned. Please do not put your hand deep into the hollow portion when removing mishandled paper.
2 2.3.7 Warning and Caution Labels 2.3 Caution Labels on Multi Puncher GP-501 7 WARNING - This safety message means you could get an electrical shock because disconnecting power from this section does not cut off power from adjacent sections of the machine. 7 WARNING - 2-16 This safety message means that you might get seriously hurt or killed if you open the product and expose yourself to hazardous voltage. NEVER remove the screws on covers.
2.3 2.3.8 Warning and Caution Labels 2 Caution Labels on Auto Ring Binder GP-502 7 CAUTION NEVER put your hand on the display panel when closing the upper part of the auto ring binder! Otherwise, you may be injured. Please be careful when closing the upper part of the auto ring binder. 7 CAUTION When the top cover or bypass deck of the ring binder is opened, be careful of your head. Otherwise, you may be injured getting bumped on your head. Please be especially careful when removing mishandled paper.
2 Warning and Caution Labels 2.3 7 WARNING - This safety message means you could get an electrical shock because disconnecting power from this section does not cut off power from adjacent sections of the machine. 7 WARNING - 2-18 This safety message means that you might get seriously hurt or killed if you open the product and expose yourself to hazardous voltage. NEVER remove the screws on covers. ALWAYS refer service requirements to qualified service personnel.
2.4 2.4 Installation Space 2 Installation Space Allow sufficient space for facilitating print operation, changing parts, and periodic inspection. Leave an adequate space behind the machine to let hot air out from the rear fan. The whole machine may weigh approx. 1,830 kg (4,034.39 lb) at maximum, depending on the combination of options. Be sure to choose a level and solid floor for the installation place.
2 2-20 Installation Space 2.
2.
2 2-22 Installation Space 2.
2.
2 2-24 Installation Space 2.
2.
2 Installation Space 2.4 Additional space will be required when the following options are installed. 2-26 RU-509 + 410 mm PI-PFU + 871.5 mm RU-509 and PI-PFU + 1,281.5 mm GP-501 + 305 mm GP-501+RU-509 + 715 mm GP-501+RU-509+PI-PFU + 1,586.5 mm GP-501+PI-PFU + 1,176.5 mm GP-502 + 655 mm GP-502+RU-509 + 1,065 mm GP-502+RU-509+PI-PFU + 1,936.5 mm GP-502+PI-PFU + 1,526.
2.
2 2-28 Installation Space 2.
2.
2 2-30 Installation Space 2.
2.
2 2.5 Operation Precautions 2.5 Operation Precautions To ensure the optimum performance of this machine, observe the precautions described below. 2.5.1 Power source The power source requirements are as follows. Destination North America Europe, Southeast Asia, Australia Voltage 208 V to 240 V AC 220 V to 240 V AC Frequency 60 Hz 50-60 Hz Use a power source with as little voltage or frequency fluctuations as possible. 2.5.
2.5 2.5.8 Operation Precautions 2 Precaution for use of Folding Unit and Finisher The primary (main) tray of Folding Unit FD-503 or of Finisher FS-532 gradually goes down while printed materials output. DO NOT allow any object to interfere with the operation of the tray on the left side of the finisher, as any interference may cause damage to the finisher or injury.
2 Operation Precautions 2.
2.
2 Operation Precautions 2.
2.
2 Operation Precautions 2.
2.
2 Operation Precautions 2.
http://konicaminolta.
