IP-711 Print Controller Read this manual before printing. Keep readily available for reference.
i Welcome This User Manual explains the functions and operations of the printer controller model IP-711 for the Konica digital color copier Konica 8020/8031. To ensure that the controller is used correctly, first read this manual carefully and thoroughly; then, keep it close at hand so you can refer to it whenever it becomes necessary. The information contained in this manual is subject to change without notice.
ii Welcome Precautions for Using the Controller Heading Precautions For the U.S.A. Users FCC Part 15-Radio Frequency Devices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
iii Welcome For Canada Users Interference-Causing Equipment Standard (ICES-003 Issue 3) This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. For European Users CE Marking (Declaration of Conformity) This product complies with the following EU directives: 89/336/EEC, 73/23/EEC and 93/68/EEC directives. This declaration is valid for the area of the European Union.
iv Welcome For users in countries not subject to Class B regulations WARNING This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. This device must be used with a shielded parallel cable, a shielded USB cable and a shielded Ethernet 10/100 Base-T cable. The use of non-shielded cables is likely to result in interference with radio communications and is prohibited under CISPR 22 rules and local rules.
v Welcome Product Overview The IP-711 controller is optional equipment used for adding printer, scanner and network functions to the Konica 8020/8031 copier. Mounting the controller on the Konica 8020/8031 will allow the following functions to be used: • Print functions effected through PCL5c • Supporting TCP/IP, NetBEUI, and IPX/SPX network protocols. • Direct printing functions over the network using Windows Printing, LPR, IPP, and others.
vi Contents Welcome About This Manual .......................................................... i Naming of Equipment ...................................................... i Precautions for Using the Controller ............................... ii Heading Precautions .................................................. ii Trademark Acknowledgments ................................... iv Product Overview ............................................................ v 1. Before Using the Controller 1.
vii Contents Advanced Operations 6. Printing 6.1 Device Option Setting ............................................... 47 6.2 Using Easy Set .......................................................... 47 6.3 Displaying Page Layout and Printer Figure .............. 48 6.4 Effecting N-up Printing ............................................ 49 6.5 Printing Pages with Watermarks ............................... 50 6.6 Effecting Duplex/Booklet Printing ........................... 54 6.7 Effecting Staple ........
viii Contents Internet Fax Reception............................................... 105 7.7 The Operation of Capturing Images by TWAIN ...... 106 Installing the TWAIN Driver..................................... 106 Controller Setting....................................................... 106 Capturing Images by TWAIN.................................... 107 7.8 Advance Registration of Destinations ...................... 110 One-Touch Key Registration .....................................
1 1. Before Using the Controller 1.1 Operating Environment Operating Environment The printer controller operates under the following environment. OS Windows 98, Windows 98SE, Windows Me, Windows NT 4.0, Windows 2000, Windows XP PC IBM PC or compatatible Direct Connection USB (version 1.1) IEEE1284 (Compatible/Nibble/ECP) Network Environment Connection scheme Ethernet 10Base-T, 100Base-TX Protocol TCP/IP IPX/SPX (NetWare 3.
2 1.
3 Setup
4
5 2. Connecting the Cable Make the cable connection between the PC and the controller by using the appropriate cable for the specific connection scheme used. If the copier is to be used in stand-alone environment, use the IEEE1284 (Centronics) or USB cable. If the copier is used in network environment, use the network cable. 2.1 Connector Locations (1) (2) (3) LED1 LED2 4334O034AA (1) USB (2) IEEE1284 (Centronics) (3) Network ■ Connecting the Network Cable 1.
6 2.
7 3. Settings Required for Local Connection To make a local connection between the PC and printer controller, make the settings by following the procedures given below. 3.1 Installing the Printer Driver For Windows 98, 98SE and Me: The following procedure applies to the installation of the printer driver for Windows 98. NOTE To connect the copier to a PC, in which Windows 98, 98SE, or Me is installed, through the USB, it is necessary that the USB device driver be installed in the PC.
8 3. Settings Required for Local Connection 5. A window will appear, prompting you to select the manufacturer and model of your printer. Click the “Have Disk..” button on the lower right part of the screen. 4668P005CA 6. The “Install From Disk” dialog box will appear. Insert the Printer Driver CD-ROM, which comes with the controller, in the CDROM drive of your PC. 7.
9 3. Settings Required for Local Connection 9. A window that prompts you to select the port will appear. Select “EPUSB1” if the connection is made through the USB cable and “LPT1” if the connection is made through the IEEE1284 cable. Then, click the “Next>” button. 4668P009CA 4334P227CA 10. A window that asks you to confirm the printer name will appear. Check the printer name.
10 3. Settings Required for Local Connection 12. Installation will complete. When all the files have been copied from the CD-ROM, the corresponding icon will be added to the “Printers” window. This completes the installation.
11 3. Settings Required for Local Connection For Windows 2000, NT 4.0, and XP: The following procedure applies to the installation of the printer driver for Windows 2000. Note that different names are used for the Windows NT users and different contents of displays are given for the Windows XP users. 1. Click the “Start” button and, from the menu that will then appear, select “Settings” – “Printers.” 2. The Printers window will appear. Double-click the “Add Printer” icon in the window. 3.
12 3. Settings Required for Local Connection 6. A window will appear, prompting you to select the manufacturer and model of your printer. Click the “Have Disk..” button on the lower right part of the screen. 4668P022CA 7. The “Install From Disk” dialog box will appear. Insert the Printer Driver CD-ROM, which comes with the printer controller, in the CD-ROM drive of your PC. 8.
13 3. Settings Required for Local Connection 9. A “Printers” list will appear. Select the printer driver to be installed and click the “Next>” button. k4334P161CA 10. A window that asks you to confirm the printer name will appear. Check the printer name. “Konica IP-711_8031/9331 PCL5c ” or “Konica IP-711_8020/9231 PCL5c ” If you want to designate this printer as the default printer, select “Yes.” Click the “Next>” button. 11. A screen that allows you to select whether to share the printer or not.
14 3. Settings Required for Local Connection 13. As the last step, click the “Finish” button. k4334P162CA 14. Installation will complete. When all the files have been copied from the CD-ROM, the corresponding icon will be added to the “Printers” window. This completes the installation.
15 3. Settings Required for Local Connection Installation through Plug and Play If the local connection (IEEE1284 or USB) is made between the PC and the copier, the printer driver can be installed through the “Plug and Play” function. For details of how to install the printer driver, see “3. Setting Required for Local Connection.” ☞p.7 NOTE Windows NT 4.0 does not support “Plug and Play.” ■ Connecting the IEEE1284 (Centronics) Cable 1. Make the connection after the copier and PC have been turned OFF. 2.
16 3. Settings Required for Local Connection • Windows 2000 and XP: 1. Connect the USB cable to the copier and PC with the Power Switch ON. 2. The installation of the printer driver through Plug and Play is automatically started on the PC. 3. Install the printer driver according as instructed by the “Add New Hardware Wizard.” NOTE Windows NT 4.0 does not support USB. Local Interface Setting If necessary, set the local interface on the copier control panel. 1.
17 4. Settings Required for Network Printing This chapter explains the settings that need to be made for network printing. Make the necessary settings for network printing by following the procedures given below. 1. Referring to “3. Settings Required for Local Connection,” install the printer driver. ☞p.7 At this time, select “LPT1” for the port. NOTE Do not execute a test print at this time. Do that after the network connections and settings have been made. 2.
18 4. Settings Required for Network Printing 4.2 To Make the Settings on the Controller Side Network settings on the controller side may be made either from the copier control panel or through Network Management Utility Light used on a PC connected to the network. Use of Network Management Utility Light allows detailed settings that cannot be made from the copier control panel to be made. For the details of Network Management Utility Light, see “Appendix B. How to Use Network Management Utility Light.
19 4. Settings Required for Network Printing ■ Accessing Network Management Utility Light Network Management Utility Light can be accessed directly using a Web browser. 1. Start the Web browser. 2. Type the IP address of the controller as follows in the address box and press the Enter key. http:/// E.g.: If the controller IP address is 172.16.0.100 http://172.16.0.100/ 3. Network Management Utility Light will appear.
20 4. Settings Required for Network Printing 4.3 Windows Printing Setting The use of Windows Printing enables direct printing over the Microsoft network. NOTE To make the Windows Printing setting, it is necessary to install the NetBEUI protocol in the PC. Settings made on the controller side Make the settings for Windows Printing from Network Management Utility Light. The setting is necessary for Windows Printing. 1. Start Network Management Utility Light. 2.
21 4. Settings Required for Network Printing NetBIOS Name Setting value Printing Service Name Setting value WorkGroup Name Setting value : : : : : : Set the NetBIOS name. 15 alphanumeric characters or less Set the print service name. 13 alphanumeric characters or less Set the work group name. 15 alphanumeric characters or less Settings made on the Printer Driver side • Windows 98, 98SE and Me: 1. Click the “Start” button and, from the menu that will then appear, select “Settings” – “Printers.
22 4. Settings Required for Network Printing 4.4 Settings for Printing through LPR The following explain how to make settings for printing through LPR in different OSs. Settings made on the controller side Set the IP address in the controller. ☞p.18 Settings made on the Printer Driver side • Windows NT 4.0: 1. Click the “Start” button and, from the menu that will then appear, select “Settings” – “Printers.
23 4. Settings Required for Network Printing 4.5 Settings for Printing using IPP Settings made on the controller side If IPP (Internet Printing Protocol) is used, make the following settings on Network Management Utility Light. (Printing can be done with the default settings.) 1. 2. 3. 4. Start Network Management Utility Light. Enter the password to log on to the Administrator mode. Click the “Network” tab and then select “Common Setting” – “IPP.” Make the following settings.
24 4. Settings Required for Network Printing Furthermore, make settings as they relate to IPP printing. 1. Click the “Print” tab and then select “IPP.” k4334P154CA 2. Make the following settings. Printer Name : Set the printer name. Setting value : 127 alphanumeric characters or less Printer Location : Set the installed site of the printer. Setting value : 127 alphanumeric characters or less Printer Manufacturer and Model: Set the manufacturing information of the printer.
25 4. Settings Required for Network Printing Settings made on the Printer Driver side • Windows 2000 and XP: 1. Click the “Start” button and, from the menu that will then appear, select “Settings” – “Printers.” Start the printer addition wizard and select “Network printer.” 2. Select the “Locate Your Printer” tab and then select “Connect to a printer on the Internet or on your intrernet.” 3. Type http://“IP address”/ipp in the “URL” field. 4. Insert the printer driver CD-ROM in the CD-ROM drive. 5.
26 4. Settings Required for Network Printing 4.6 Print Service Setting in NetWare ■ Print settings on the PC from which printing is effected The controller supports the following environment. NetWare Version Protocol Emulation Service Mode NetWare 3.2 IPX Bindery PServer/Rprinter NetWare 4.x IPX NDS, Bindery emulation PServer/Nprinter NetWare 5.x IPX, TCP/IP NDS PServer/NDPS (lpr) ■ NetWare Server Setting Procedure • NetWare 3.2 print server mode settings 1.
27 4. Settings Required for Network Printing 17. Select “IP-711” created in step 12 from the “Defined printer” list and press “Enter.” 18. Press “Insert” to display the “Available Queue” list of the printer. 19. Select the print queue prepared in step 4. Specify priority using a corresponding number, 1 being the top priority and 10 being the lowest. Then, press “Enter” to validate the selection. 20. Press “Esc” to quit Pconsole.
28 4. Settings Required for Network Printing • NetWare 3.2 remote printer mode settings 1. Log on to the NetWare server, in which PServer is to be registered, by the Supervisor right. 2. Start Pconsole. 3. Select “Print Queue Information” from “Available Options” and then press “Enter.” 4. Click “Insert,” type “Print Queue Name,” and press “Enter” to register the [print queue name]. 5. Press “Esc” to return to “Available Options.” 6. Select “Print Server Information” and press “Enter.” 7.
29 4. Settings Required for Network Printing 22. Using Network Management Utility Light, set the controller as detailed below and restart it. k4334P163CA Details of Setting: Enable NetWare Frame Type Bindery/NDS Print Server Name Print Server Password Mode Printer Number : Enable : Auto Detect (Select the frame type according to the network environment.) : Bindery : Print server name created in step 7 : (Set only when the password is set on the NetWare server side.
30 4. Settings Required for Network Printing • NetWare 4.x NDS print server mode settings 1. Log on to the NDS Tree by the Administrator right. 2. Start NWADMIN. 3. Select the container object, either Organization or Organizational Unit, that offers the print service and select “Print Service Quick Setup” from the tool menu. 4. Type “Print server name,” “Printer name,” “Print Queue Name,” and “Volume.” Then, set “Remote Other/Unknown” for the “Type” name of the printer and save the settings.
31 4. Settings Required for Network Printing Print Server Password Preferred NDS Context Preferred NDS Tree Print Queue Scan Rate Mode : (Set only when the password is set on the NetWare server side.) : Name of the context to which PServer is connected : Name of the tree to which PServer logs on : 1 (Change as necessary.) : PServer 6. At the NetWare server console, load MONITOR.NLM. 7. Select “Connection Information” and check that the PServer created is connected in the active connection column.
32 4. Settings Required for Network Printing • NetWare 4.x NDS remote printer mode settings 1. Log on to the NDS Tree by the Administrator right. 2. Start NWADMIN. 3. Select the container object, either Organization or Organizational Unit, that offers the print service and select “Print Service Quick Setup” from the tool menu. 4. Type “Print Server Name,” “Printer name,” “Print Queue Name,” and “Volume.” Then, set “Remote Other/Unknown” for the “Type” name of the printer and save the settings.
33 4. Settings Required for Network Printing Print Server Password Preferred NDS Context Preferred NDS Tree Print Queue Scan Rate Mode Printer Number : (Set only when the password is set on the NetWare server side.) : Name of the context in which PServer is loaded : Name of the tree in which PServer is loaded : 1 (Change as necessary.) : Nprinter/Rprinter : 255 (Set 255 or the numbers (0-254) assigned to the printer.) 6. At the NetWare server console, load PSERVER.NLM. 7.
34 4. Settings Required for Network Printing • NetWare 5.x NDS print server mode settings * To use the print server mode, it is necessary that the IPX protocol have been loaded in the NetWare server. 1. Log on to the NDS Tree by the Administrator right. 2. Start NWADMIN. 3. Select the container object, either Organization or Organizational Unit, that offers the print service and select “Print Service Quick Setup” from the tool menu. 4.
35 4. Settings Required for Network Printing Print Server Name Print Server Password Preferred NDS Context Preferred NDS Tree Print Queue Scan Rate Mode : Print server name created in step 4 : (Set only when the password is set on the NetWare server side.) : Name of the context to which PServer is connected : Name of the tree to which PServer logs on : 1 (Change as necessary.) : PServer 6. At the NetWare server console, load MONITOR.NLM. 7.
36 4. Settings Required for Network Printing • NetWare 5.x Novell Distributed Print Service (NDPS) settings * Before making settings for NDPS, make sure that the NDPS Broker and NDPS Manager have been created and loaded. * Before starting the procedure, make sure that the TCP/IP protocol has been set in the NetWare server and an IP address has been assigned to the controller, and started, using Network Management Utility Light. k4334P153CA Creating the NDPS Printer Agent 1.
37 4. Settings Required for Network Printing 10. Set the IP address set in the controller for the host address, type “Print” in “Printer name,” and press “Finish” to validate the settings. 11. The printer driver registration screen will then appear. Select “None” for all OSs and complete the registration procedure. * For the printer user rights, printer notification option, and assignment of multiple queues, see the document available for NetWare and set them as necessary.
38 4. Settings Required for Network Printing • Client Print Setting Click “Start” – “Settings” – “Printers” and then double-click the “Add Printer” icon. Refer to the network in the destination port setting and specify the queue name previously created (NDPS printer name). On the list of printer models, select the driver from the printer driver CD-ROM. Complete the installation procedure according as instructed by the wizard.
39 4. Settings Required for Network Printing 4.7 Operation Checks after Installation of Driver Test Printing from Client PC A test page is printed to check to see if the printer driver has been properly installed. 1. Click the “Start” button and, from the menu that will then appear, select “Settings” – “Printers.” 2. Select the icon of the printer that has been installed; then, right-click it and choose “Properties.” 3. From the screen that will then appear, click the “Print Test Page” button.
40 4.
41 5. Uninstalling the Driver 5.1 Uninstalling the Driver 1. Click the “Start” button and, from the menu that will then appear, select “Settings” – “Printers.” 2. Click the icon of the printer to be deleted. 3. Select the “Delete” key to delete the driver. 4. When the uninstalling procedure is completed, the printer icon disappears from the “Printers” window. This completes the uninstalling procedure.
42 5.
43 Advanced Operations
44
45 6. Printing This chapter explains printing operations that can be set from the printer driver. How to Display the Printer Driver Property Sheet There are two approaches available for use to display the property sheet. (Each offers different ranges of settings that can be incorporated.) • Displaying the property sheet from the printer folder 1. Click the “Start” button and, from the menu that will then appear, select “Settings” – “Printers.” 2.
46 6. Printing Following give an overview of each function available from different tabs. Tab Name Setup Paper Quality Device Option Setting Job Management Function Name Description N-up Print two or more pages on a sheet of paper. Ref.: Effecting N-up Printing ☞p.49 Watermark Print pages with text put in the background. The text can be changed or edited. Ref.: Printing Pages with Watermarks ☞p.50 Duplex/Booklet Set Duplex or Booklet function. Ref.: Effecting Duplex/Booklet Printing ☞p.
47 6. Printing 6.1 Device Option Setting Options installed on the copier are enabled from the printer driver. Setting Procedure 1. Start the printer driver and select the “Device Option Setting” tab. 2. From the “Installable Options” list, select the device to be installed and click the “Add” button. k4334P249CA Check that the selected option is now shown under the “Installed Options” list. 6.2 Using Easy Set The current setting value can be saved under a name you specify.
48 6. Printing 6.3 Displaying Page Layout and Printer Figure 4334P242CA • Page Layout shows a simplified image of a printed page. • Printer Figure shows the devices mounted on the copier. MEMO Page Layout allows you to check how a printed page will look like before actually printing it.
49 6. Printing 6.4 Effecting N-up Printing N-up printing refers to the function that prints a document consisting of two or more pages on a sheet of paper. It comes in handy for printing a large volume of data and reducing the number of printed pages. Setting Procedure 1. Click the “Setup” tab. 2. In the “N-up” function, select any one of the following N-up subfunctions. 2-up 4-up 9-up 16-up 4334P033AA When “Border Line” is selected, the boundary line of each page will be printed. 3.
50 6. Printing 6.5 Printing Pages with Watermarks Specific text is printed in the background. Watermark Print 4692O098BA Setting Procedure 1. Select the “Setup” tab. 2. From the list of “Watermark,” select the desired text to be put in the background as a watermark. Text 1st Page Only Edit Watermark : Select the word to be entered as the watermark. , CONFIDENTIAL, TOP SECRET, COPY, DO NOT COPY, DRAFT, FINAL, PROOF : The watermark is placed only on the first page.
51 6. Printing Editing the Watermark Clicking “Edit Watermark” will allow you to edit the font and position of the watermark. (1) (2) (3) (4) (5) 4334P243CA (1) Preview Displays the print image. (2) Watermark text Select the desired watermark from the list of existing watermarks. (3) New Click to create new text. It will open a dialog box for setting details. (4) Edit Click to edit the text selected from (2). It will open a dialog box for setting details.
52 6. Printing Details Setting (1) (2) (3) (4) (5) (6) (7) (8) (9) 4334P244CA (1) Name Type the name of the new watermark (consisting of up to 20 characters). (2) String Type the character string to be printed as the watermark (consisting of up to 127 characters). (3) Type Face Select the font of the watermark from among the fonts installed in the PC. (4) Size Specify the size of the characters (from 8 points to 200 points). (5) Style Specify the style of the characters. • Bold : Prints bold characters.
53 6. Printing (8) Angle: Specify the angle of characters with reference to the paper. • Fixed Angle : Standard fixed angle provided by the printer driver. Setting values: Horizontal, Diagonal, Vertical, User Setting • User Setting : When User Setting is selected for Fixed Angle, you can set an arbitrary angle. Setting value: -180 to +180 degrees (-: clockwise; 0: horizontal; +: counterclockwise) (9) Position: Specify the position of the watermark.
54 6. Printing 6.6 Effecting Duplex/Booklet Printing A document can be printed onto both sides of a sheet of paper or into a booklet format (two facing pages). This function can be used only when the copier is equipped with an Automatic Duplex Unit. Duplex Printing Top Binding Print data Left Binding Printout Print data 4608O008AA Printout 4608O009AA Booklet Printing Print data Printout 4608O011AB Setting Procedure 1. Select the “Setup” tab. 2.
55 6. Printing 6.7 Effecting Staple The Staple function can be used only when the copier is equipped with the Finisher FS-231 or FS-135. 1. Select the “Setup” tab. 2. Clicking “Detail of Output Setting” will open a dialog box for setting details. Make the following settings in the “Staple” column. • If FS-231 is mounted: OFF, Corner, Top Side 2 Points, Left Side 2 Points, Auto 2 Points • If FS-135 is mounted: OFF, Corner NOTE • When the FS-135 is mounted, stapling can be made up to 30 sheets of paper.
56 6. Printing 6.8 Effecting Folding Folding is used in combination with Booklet to produce a booklet through center folding and center stapling. It can be used only when the copier is equipped with the Finisher FS-231. Setting Procedure 1. Select the “Setup” tab. 2. Clicking “Detail of Output Setting” will open a dialog box for setting details. Make the following settings in the “Folding” column. OFF : Disables folding.
57 6. Printing 6.9 Effecting Hole Punch The Hole Punch function can be used only when the copier is equipped with the Finisher FS-231. Setting Procedure 1. Select the “Setup” tab. 2. Clicking “Detail of Output Setting” will open a dialog box for setting details. Make the following settings in the “Punch” column.
58 6. Printing 6.10 Adding a Cover or Interleaf A front cover and/or a back cover can be added to each of your copy sets. When printing on sheets of OHP transparencies, an interleaf can also be inserted between sheets of OHP transparencies. Setting Procedure 1. Select the “Setup” tab. 2. In the “Paper Source” function, clicking “Detail of Paper Source” will open a dialog box for setting details. • Cover A front cover and/or a back cover can be added to each of your copy sets.
59 6. Printing 6.11 Print to Suit the Paper Size The image on the document created with an application can be enlarged or reduced when printing according to the paper size. Print data Printout 1149O004AA Setting Procedure 1. Select the “Paper” tab. 2. Check that “Original Document Size” represents the size of the document created with the application. 3. For “Output Paper Size,” specify the size of the output paper. 4.
60 6. Printing 6.12 Printing on Paper from Manual Bypass Tray The Manual Bypass Tray can be selected as the paper source for printing. 1. 2. 3. 4. Select the “Setup” tab. Select “Manual Feed Tray” from the “Paper Source” list. Click “OK” twice to send the job. Load the Manual Bypass Tray of the copier with paper. NOTES • Place one sheet of paper at a time. • An error message will be displayed on the control panel of the copier if a print job is sent with paper loaded in the Manual Bypass Tray.
61 7. Settings and Operations for Scan Functions This chapter explains how to make settings for and operate the scan functions that become usable when the controller is added. The copier control panel or Network Management Utility Light is used for setting. Refer to Usage of Network Management Utility Light on Appendix B for the procedures to start Network Management Utility Light and log in the administrator mode. ☞p.
62 7. Settings and Operations for Scan Functions 7.1 Scan Settings (Basic Settings) Make the basic settings for scan functions. Setting from Network Management Utility Light 1. Start Network Management Utility Light. 2. Enter the password and log on to the Administrator mode. 3. From the “Scan” tab, select “Scan.” k4334P171CA 4. The following items can be set. • Scan Device Name : The characters set for this parameter is appended before the name of the image file created with the scan function.
63 7. Settings and Operations for Scan Functions URL Notification URL Notification notifies, by means of e-mail, information on the location, in which scanned data created through a scan function is stored. The scanned data is not attached to the e-mail message. The party that receives the e-mail message refers to the information given in the email message to access the image data storage location. MEMO The information does not contain the user name or password.
64 7. Settings and Operations for Scan Functions 7.2 Scan to PC Scan to PC is the function that transmits image data scanned by the copier to the PC using FTP. It is necessary that the FTP server application be started on the PC side. PC FTP Server Application Software 4334O001AA 1. Using Network Management Utility Light, make the setting for One-Touch Key Registration or One Time Registration.
65 7. Settings and Operations for Scan Functions Setting the FTP Application It is the function that transmits data using following settings of FTP. If necessary, set following by FTP application of receiving PC. • Login Name • Password : anoyamous : “POP3 login name” @ “IP address of the printer controller” How to Check the Password 1 Start the Network Management Utility Light, and log on to the Administrator mode. 2.
66 7. Settings and Operations for Scan Functions Scan Operation You have the choice of two scan operating procedures available selected according to whether the one-touch key is used to specify the destination or one time key is used. ■ 1. 2. 3. 4. Specifying the destination using a one-touch key: Press the Scan key on the copier. Select the “Destination” tab. Select the “IndexList” key. Select the target index from the index list. Touch “Enter.” (Registering Index ☞p.110) 5.
67 7. Settings and Operations for Scan Functions Details of Scan Operation Settings ■ 1. 2. 3. Setting the Scanning Mode Press the Scan key on the copier. Select the “Scan Mode” tab. Set the following items. Scan Size Resolution Setting values File Format Setting values Color Mode Setting values Background Remove : Set the scanning size for the document. Or, specify any given size (in mm or 1/16”). : Select the scanning resolution.
68 7. Settings and Operations for Scan Functions ■ Setting Checks It is possible to check the details of settings on the copier control panel. • Select the “CHECK” key. • Check the settings of “Scan to PC.
69 7. Settings and Operations for Scan Functions 7.3 Scan to FTP Server Scan to FTP Server is the function that transmits image data scanned by the copier to the FTP server. PC Scan data Information Mail server FTP server Mail server 4334O002AA 1. Using Network Management Utility Light, register the FTP servers (up to five). ☞p.70 2. Using Network Management Utility Light, make the setting for One-Touch Key Registration or One Time Registration.
70 7. Settings and Operations for Scan Functions 5. Press the Start key on the copier. This lets the copier scan the document and send the scanned data to the FTP server. If the URL notification party has been specified, the information on the location, in which scanned data is stored, is transmitted by e-mail. 6. Download the scanned data from the FTP server using the FTP client software.
71 7. Settings and Operations for Scan Functions 4. When an empty field, in which no FTP servers have previously been registered, is selected, it will bring you to a server registration screen. k4334P173CA 5. Set the following items. IP Address Login Name Setting value Password Setting value Port Number Directory Setting value Use Proxy Setting values : Specify the IP address of the FTP server. : Specify the name with which to log on to the FTP server.
72 7. Settings and Operations for Scan Functions External Server Link Setting values : Set “Enable” and double-click the IP address of the FTP displayed on the server link screen, which will access the FTP server. The server link screen can be displayed by selecting “Filing” – “External Server Link.” : Yes, No NOTE “External Server Link” can be used only when “anonymous” is set in “Login Name” on the FTP Server Registration screen. Setting from the copier control panel 1.
73 7. Settings and Operations for Scan Functions Setting the Proxy Server Make the following settings to use the proxy server. Setting from Network Management Utility Light 1. Start Network Management Utility Light. 2. Enter the password and log on to the Administrator mode. 3. From the “Network” tab, select “FTP Server” – “FTP Server Configuration.” k4334P174CA 4. Set the following items. Proxy IP Address : To use a proxy server, set the IP address of the proxy server.
74 7. Settings and Operations for Scan Functions Scan Operation You have the choice of two scan operating procedures available selected according to whether the one-touch key is used to specify the destination or one time key is used. ■ 1. 2. 3. 4. Specifying the destination using a one-touch key: Press the Scan key on the copier. Select the “Destination” tab. Select the “IndexList” key. Select the target index from the index list. Touch “Enter.” (Registering Index ☞p.110) 5.
75 7. Settings and Operations for Scan Functions Details of Scan Operation Settings ■ 1. 2. 3. Setting the Scanning Mode Press the Scan key on the copier. Select the “Scan Mode” tab. Set the following items. Scan Size Resolution Setting values File Format Setting values Color Mode Setting values Background Remove : Set the scanning size for the document. Or, specify any given size (in mm or 1/16”). : Select the scanning resolution.
76 7. Settings and Operations for Scan Functions ■ URL Notification This function notifies the information on the location, in which scanned data is stored, by e-mail. • Select the notifying party using one-touch key registration. • The party is one selected from among only those registered in one-touch key registration with e-mail addresses. Procedure 1. Press the “SCAN” key on the copier. 2. Select the “Auxiliary” key to go to the “Auxiliary” screen. 3.
77 7. Settings and Operations for Scan Functions 7.4 Scan to HDD Scan to HDD is the function that saves image data scanned by the copier in the HDD directories of the hard disk built in the copier. The image data saved in the hard disk can be downloaded to the PC using Network Management Utility Light. For management of the saved data, see “Job Operations on Network Management Utility Light,” “Job Management” of chapter 8. ☞p.121 NOTE The hard disk is optional.
78 7. Settings and Operations for Scan Functions MEMO Even if URL Notification has not been set during One-Touch Key Registration or One Time Registration on Network Management Utility Light, it is possible to specify the URL Notification party from the copier control panel. ☞p.82 5. Press the Start key on the copier. This lets the copier scan the document and save the scanned data in the hard disk.
79 7. Settings and Operations for Scan Functions • “Public directory” and “HDD directories” The “directory name” can be freely assigned for “HDD Directories”. It is the location, in which scanned data is stored for Scan to HDD. The contents of the “HDD directories” can be accessed only when the password set upon registration is entered. The “HDD directories” can be created arbitrarily from a Network Management Utility Light screen.
80 7. Settings and Operations for Scan Functions Scan Operation You have the choice of two scan operating procedures available selected according to whether the one-touch key is used to specify the destination or one time key is used. ■ 1. 2. 3. 4. Specifying the destination using a one-touch key: Press the Scan key on the copier. Select the “Destination” tab. Select the “IndexList” key. Select the target index from the index list. Touch “Enter.” (Registering Index ☞p.110) 5.
81 7. Settings and Operations for Scan Functions Details of Scan Operation Settings ■ Setting the Scanning Mode 1. Press the Scan key on the copier. 2. Select the “Scan Mode” tab. 3. Set the following items. Scan Size Resolution Setting values File Format Setting values Color Mode Setting values Background Remove : Set the scanning size for the document. Or, specify any given size (in mm or 1/16”). : Select the scanning resolution.
82 7. Settings and Operations for Scan Functions ■ URL Notification This function notifies the information on the location, in which scanned data is stored, by e-mail. • Select the notifying party using one-touch key registration. • The party is one selected from among only those registered in one-touch key registration with e-mail addresses. Procedure 1. Press the “SCAN” on the copier. 2. Select the “Auxiliary” key to go to the “Auxiliary” screen. 3.
83 7. Settings and Operations for Scan Functions Downloading Scanned Data from the Hard Disk Start Network Management Utility Light and download the scanned data. 1. Start Network Management Utility Light. 2. Select “File” – “User Directory.” k4334P185CA 3. Click the specified HDD directories or PUBLIC. 4. If the HDD directories has been clicked, type the password.
84 7. Settings and Operations for Scan Functions 5. A list of files stored is displayed. Select the specific file to be downloaded and click the “Acquire Selected File” button. 4334P186CA Data list screen File Name Received Time File Size : Displays the name of the file stored in the HDD directories. : Displays the time-of-day when the file was stored in the HDD directories. : Displays the size of the file stored in the HDD directories.
85 7. Settings and Operations for Scan Functions 6. Follow these procedures to acquire the scanned data from Network Management Utility Light. For TIFF and PDF format 1. It opens “Downloading files...” dialog box. 2. Specify the place in which the files can be downloaded, then click “OK” button. For JPEG format 1. Scanned image will then appear. 2. Click and select on the image and show the menu by right-click. 3. Select “Save the image as...” and save the file.
86 7. Settings and Operations for Scan Functions 7.5 Scan to E-mail Scan to E-mail is the function that transmits image data scanned by the copier as a file attached to e-mail. PC Mail server Mail server 4334O004AA If the size of the file attached to e-mail is limited and if a file size exceeds this limit, the file may be divided (in binary units) for transmission. For mail (file) division setting, see “Scan to E-mail Setting” of chapter 7. ☞p.88 1.
87 7. Settings and Operations for Scan Functions Controller Setting ■ E-mail Transmission Setting Set the mail server (SMTP server) to enable mail transmission. Setting from Network Management Utility Light 1. Start Network Management Utility Light. 2. Enter the password and log on to the Administrator mode. 3. From the “Network” tab, select “E-mail/Internet FAX” – “Send.” k4334P175CA 4. Set the following items. SMTP Server Port Number : Set the IP address of the SMTP server.
88 7. Settings and Operations for Scan Functions Setting from the copier control panel 1. Enter the Administrator mode. 2. Select “Network set” – “E-mail/I-Fax” – “Send.” 3. Set the SMTP Server, Timeout of SMTP Server, and Mail Separation. Binary Division and Scanned File Separation ☞p.62 Different mail transmission operations of Scan to E-mail result depending on the combination of the settings of Binary Division and Scanned File Separation. Examine the following.
89 7. Settings and Operations for Scan Functions ■ Setting the Mail Options The subject and message of e-mail can be set for mail transmission through Scan to E-mail. Setting from Network Management Utility Light 1. Start Network Management Utility Light. 2. Enter the password and log on to the Administrator mode. 3. From the “Network” tab, select “E-mail/Internet FAX” – “E-mail.” k4334P177CA 4. Set the following items.
90 7. Settings and Operations for Scan Functions Scan Operation You have three ways to choose from to perform the scan operation depending on whether the destination is set with a one-touch key or a one time key, or set through direct input from the copier control panel. ■ 1. 2. 3. 4. Specifying the destination using a one-touch key: Press the Scan key on the copier. Select the “Destination” tab. Select the “IndexList” key. Select the target index from the index list. Touch “Enter.
91 7. Settings and Operations for Scan Functions ■ Direct Input The address used in Scan to E-mail can be directly input from the control panel of the copier, instead of using the one-touch key or one time key. 1. Press the Scan key on the copier. 2. Select “Direct.” 4334P202CA 3. Select “E-MAIL.” 4. Using keys on the control panel and 10-Key Pad, type the e-mail address of the destination.
92 7. Settings and Operations for Scan Functions Details of Scan Operation Settings ■ 1. 2. 3. Setting the Scanning Mode Press the Scan key on the copier. Select the “Scan Mode” tab. Set the following items. Scan Size Resolution Setting values File Format Setting values Color Mode Setting values Background Remove : Set the scanning size for the document. Or, specify any given size (in mm or 1/16”). : Select the scanning resolution.
93 7. Settings and Operations for Scan Functions ■ Setting Checks 1. Select the “CHECK” key. 2. Select the “Send” tab to check the settings made for Scan to E-mail. k4334P205CA 3. Select the “Subject/From” tab to check the data set for “SUBJECT” and “FROM” (sender’s address). k4334P206CA 4. Select the “Contents” tab to check the message of the e-mail. k4334P207CA 5. Select the “Send” tab then “Detail” to check the e-mail address of the sender.
94 7. Settings and Operations for Scan Functions 7.6 Internet Fax Internet Fax is the function that transmits the image data captured through scanning as a file attached to e-mail. It differs from Scan to E-mail in that the format of the attached file is standardized. Image data can be transmitted and received among the a devices that complies with the Internet Fax standard. Transmission can be executed by following the same procedure as in Scan to Email.
95 7. Settings and Operations for Scan Functions 1. Using Network Management Utility Light, make the settings for mail transmission, mail reception, mail options, and printing for the Internet Fax received data. ☞p.96 2. Using Network Management Utility Light, make the setting for One-Touch Key Registration or One Time Registration.
96 7. Settings and Operations for Scan Functions Controller Setting ■ Internet Fax Transmission Setting To make the settings, use the same screen as that used for setting for Scan to E-mail. (The same transmission settings are made for Scan to E-mail and Internet Fax.) ■ Reception Setting Set the mail server (POP3 server) to enable mail reception from the lnternet FAX. Setting from Network Management Utility Light 1. Start Network Management Utility Light. 2.
97 7. Settings and Operations for Scan Functions Mail Check : Set whether to make a periodic check of the contents of the mail server or not. If “No” is selected, mail is not received. Setting values : Yes, No 1-60 min. Port Number : Set the port number of the POP3 server. (The default value of “110” is generally used.) POP3 Connection Timeout: Set the communications timeout value with the POP3 server. Setting values : 30 to 300 sec. Setting from the copier control panel 1. Enter the Administrator mode.
98 7. Settings and Operations for Scan Functions Setting the Internet FAX Options The subject and message of e-mail can be set for mail transmission through Internet Fax. Setting from Network Management Utility Light 1. Start Network Management Utility Light. 2. Enter the password and log on to the Administrator mode. 3. From the “Network” tab, select “E-mail/Internet FAX” – “Internet FAX.” k4334P178CA 4. Set the following items.
99 7. Settings and Operations for Scan Functions ■ Setting for Printing E-mail/Internet FAX Set for printing for internet FAX received data. Setting from Network Management Utility Light 1. Start Network Management Utility Light. 2. Enter the password and log on to the Administrator mode. 3. From the “Network” tab, select “E-mail/Internet FAX” – “Print.” k4334P179CA 4. Set the following items.
100 7. Settings and Operations for Scan Functions Setting from the copier control panel 1. Enter the Administrator mode. 2. Select “Network set” – “E-mail/I-Fax” – “Print.” 3. The same items as those with Network Management Utility Light can be set. Scanning Operation for Internet Fax Transmission You have three ways to choose from to perform the scan operation depending on whether the destination is set with a one-touch key or a one time key, or set through direct input from the copier control panel.
101 7. Settings and Operations for Scan Functions ■ Direct Input 1. Press the Scan key on the copier. 2. Select “Direct.” 4334P202CA 3. Select “I-FAX.” 4. Using keys on the control panel and 10-Key Pad, type the e-mail address of the destination. (1800 alphanumeric characters or less; if two or more addresses are entered, place “,” between two different addresses.) 4334P208CA 5. 6. 7. 8. Select “Enter.” This brings you back to the scan basic screen. Set the scanning mode. (Ref.
102 7. Settings and Operations for Scan Functions Details of Scan Operation Settings ■ 1. 2. 3. Setting the Scanning Mode Press the Scan key on the copier. Select the “Scan Mode” tab. Set the following items. Scan Size Resolution Setting values File Format Setting values Color Mode Setting values Background Remove : Set the scanning size for the document. Or, specify any given size (in mm or 1/16”). : Select the scanning resolution.
103 7. Settings and Operations for Scan Functions ■ Specifying the Document Set the type of the document to be scanned. 1. Press the Scan key on the copier. 2. Select the “Document Set” tab. 3. Set the following items. Original Direction Setting values : Set the placement direction of the document. : Not selected (Auto detect), Portrait documents “Place Horizontally,” “Place vertically,” Landscape documents “Place Horizontally,” “Place Vertically.” Doc. Mode : Set the document mode.
104 7. Settings and Operations for Scan Functions 2. Select the “Subject/From” tab to check the data set for “SUBJECT” and “FROM” (sender’s address). k4334P212CA 3. Select the “Contents” tab to check the message of the e-mail. k4334P213CA ■ Error Message For [E-mail Address (Reply-To:)] (Ref.: Advance Registration of Destinations ☞p.110) and [E-mail Address (From:)], set the addresses to which the mail server sends the error message when an error occurs during transmission of the e-mail.
105 7. Settings and Operations for Scan Functions Internet Fax Reception Internet Fax data (e-mail) transmitted from another device that complies with Internet Fax can be received. The received Internet Fax e-mails on the mail server are collectively retrieved from the mail server and temporarily stored in the copier. The stored data is printed, one job after another, as soon as all the jobs being currently executed are completed.
106 7. Settings and Operations for Scan Functions 7.7 The Operation of Capturing Images by TWAIN TWAIN is the interface that allows images captured by a specific device to be input through a computer of a different platform. It is applied to control the scanner of the copier so as to capture scanned images in applications. To use TWAIN, it is necessary that a TWAIN driver be installed in the PC and TWAIN settings be made on the copier.
107 7. Settings and Operations for Scan Functions Setting from the copier control panel 1. Enter the Administrator mode. 2. Select “Network set” – “Twain.” 3. The Panel lock timeout for TWAIN can be set. Capturing Images by TWAIN ■ Setting the Document 1. Select scan by TWAIN from the application. 2. Select the device (IP address + port number), from which the scanned data is to be captured. The list of image-capturing devices contains all TWAINcompatible devices on the network.
108 7. Settings and Operations for Scan Functions Pixel Type Setting values Place Setting values Duplex : : : : : Specify the type of data to be captured. Full Color, Gray Scale, Black & White Set how the document is to be scanned. Glass, ADF Select whether the document to be scanned is twosided or not. Setting values : Off, On Low Density Adjustment : Select if low density adjustment is to be made. Separate Scan : Select to handle two or more different originals. Buttons Prescan : Performs a prescan.
109 7. Settings and Operations for Scan Functions Retrieving Scanners 4334P248CA • Broadcast: Retrieves scanners by the broadcast protocol. IP Port Base : Specify the IP Port Base to be retrieved. Broadcast : Executes retrieval. • Multicasting: Retrieves scanners by the multicasting protocol. Max Hop for Search : Set the number of hops to be retrieved. IP Port Base : Specify the IP Port Base to be retrieved. Multicasting : Executes retrieval.
110 7. Settings and Operations for Scan Functions 7.8 Advance Registration of Destinations When using the scan function, it is convenient if the destination is registered through the copier control panel in advance. Network Management Utility Light is used to register the destination. One-Touch Key Registration One-Touch Key Registration allows you to call up destination at the touch of a key. It eliminates the need for entering the destination each time the scan function is used.
111 7. Settings and Operations for Scan Functions Job Type : An icon corresponding to the job type registered is displayed. Scan To E-mail icon File (Scan To PC/FTP Server) icon File (Scan To HDD) icon Scan To Internet Fax icon – Icon not registered Destination Name : Displays the destination name registered. Buttons Apply : Validates the change of the index name. Delete : Deletes the selected one-touch key registration. 4. Click the one-touch key registration box. 5. Select the appropriate job type.
112 7. Settings and Operations for Scan Functions 6. When “Group” is selected, the destination to be newly registered for one-touch key registration can be set as group transmission. 7. Clicking the “Next” button will display the items to be set for each job type. Registration Items • When “Scan To E-mail” is selected Destination Name : Specify the name of the destination to be registered for one-touch key. Setting value : 12 alphanumeric characters or less Address (To:) : Type the destination address.
113 7. Settings and Operations for Scan Functions • When File (Scan To PC) is selected Destination Name : Specify the name of the destination to be registered for one-touch key. Setting value : 12 alphanumeric characters or less IP Address : Set the destination IP address of the PC, on which the FTP application is running. • When File (Scan To HDD) is selected Destination Name : Specify the name of the destination to be registered for one-touch key.
114 7. Settings and Operations for Scan Functions E-mail Address (Reply-To:): Set the e-mail address of the sender. Setting value : 72 alphanumeric characters or less MEMO When inputting two or more addresses, put comma between the address.
115 7. Settings and Operations for Scan Functions One Time Registration Settings for One Time Registration are made using Network Management Utility Light. This function differs from One-Touch Key Registration in that, when the transmission task is executed, these settings are gone. That is, the settings for One Time Registration are valid only for one time use. If you want to recall settings a number of times, use One-Touch Key Registration. Setting Procedure 1. Start Network Management Utility Light. 2.
116 7. Settings and Operations for Scan Functions 4. Click the One Time Registration box. 5. Select the appropriate job type. k4334P191CA 6. Clicking the “Next” button will display the items to be set for each job type. Registration Items • When “Scan To E-mail” is selected Destination Name : Specify the name of the destination to be registered for one time use. Setting value : 12 alphanumeric characters or less Address (To:) : Displays a list of addresses previously set.
117 7. Settings and Operations for Scan Functions File Type : Select the file format in which the scanned image is to be stored. Setting values : TIFF, PDF, JPEG Color Mode : Select the color, in which the document is scanned. Setting values : Auto Color, Gray Scale, B/W, Full Color Background Remove : Set background removal. Orientation : Set the orientation of the document. Setting values : Auto, Portrait, Landscape Margin : Set the margin edge.
118 7. Settings and Operations for Scan Functions • When File (Scan To HDD) is selected Destination Name : Specify the name of the destination to be registered for one time use. Setting value : 12 alphanumeric characters or less HDD Directories : The list displays the HDD directories that has been registered. Password : Type the password set for the HDD directories. If “PUBLIC” is selected, there is no need to enter the password.
119 7. Settings and Operations for Scan Functions Erase : Select the erase type. Setting values : No, Left Erase, Top Erase, Frame Erase Set the erase width in mm or 1/16”. NOTE Though entry of the number characters more than the specified limit may be possible on the browser, the effective number of characters is as specified.
120 7.
121 8. Job Management 8.1 Print Job Management This chapter explains print job management. Specifying Operation for Job It is possible to specify the operation for the job in the copier by setting the printer driver. • Select the “Job Management” tab and select, from the “Store Job” list, what to do with the job after it has been electronically processed. OFF Store to HDD Store to Memory Proof and Print Lock Job : Directly printed : Stores the job in the hard disk. ☞p.124 : Stores the job in memory.
122 8. Job Management name for each job. Setting the default user name: 1. Select the “Device Option Setting” tab. 2. Type the default user name in “Default User Name” of “Job Owner” (up to 255 alphanumeric characters). Transmitting a Print Job to a Copier in Which the Copy Track Function is Active If the Copy Track function is enabled in the copier, it is necessary to enter the access number before running a print cycle.
123 8. Job Management Printing Pages with a Distribution Number To identify each print job, a distribution number can be printed in the background. The optional HDD and 256-MB memory must be mounted on the copier. 1. Select the “Job Management” tab. 2. Select “Distribution Number” of “Distribution.” 3. When “1st Page Only” is selected, the distribution number will be printed on the first page only. 4. In “Distribution Color,” specify the color (red, blue, or black) of the distribution number. 5.
124 8. Job Management Proof and Print When a print cycle is run with Proof and Print set, only the first copy will be printed, while the rest of the copies will be stored in memory. The rest will not be printed until the job is unlocked by the copier control panel. Operation on the PC Side: 1. Select the “Job Management” tab. 2. From the “Store Job” list, select “Proof and Print.” Operation on the copier side: 1. Touch “Job Control” – “Scanned Job” on the control panel to display the stored job list. 2.
125 8. Job Management Store to Memory If Store to Memory is set for a print job to be printed and the job is transmitted, the job is stored in the memory of the copier and is not printed. The setting must be canceled from the copier control panel to effect printing of the job. The job will be gone when the copier is turned OFF. Operation on the PC Side: 1. Select the “Job Management” tab. 2. From the “Store Job” list, select “Store to Memory.” Operation on the copier side: 1.
126 8. Job Management 8.2 Job Operations on Network Management Utility Light The status of the job being processed by the copier can be checked on Network Management Utility Light. It is also possible to delete or otherwise operate a job. Print job list This lists the jobs being processed for printing. Display Procedure 1. Start Network Management Utility Light. 2. From the “Job” tab, select “Active Job” – “Print.
127 8. Job Management • Detailed information displayed Division ID : Shows the access number [1 to 998] if the Copy Track function is active. Error Information : Displays the status of the job in detail. If the job status is “Printing Stopped (Error),” it shows the details of the warning. Destination : Displays the exit port of the job. When FS-135 is mounted: [Top Tray, Elevator Tray, Third Tray] When FS-231 is mounted: [Elevator Tray, Saddle Stack Tray] File Name : Displays the name of the job.
128 8. Job Management Print job history This lists the jobs which have been processed for printing. Display Procedure 1. Start Network Management Utility Light. 2. From the “Job” tab, select “Job History” – “Print.” k4334P184CA Descriptions of Contents of Display Result : Displays the result of execution of the job. [Job Completed, Job Deleted by Error, Job Deleted by User, Staple Canceled, Punch Canceled, Paper Fold Canceled] Job Name : Indicates the name of the user who has issued the job.
129 8. Job Management Destination : Displays the exit port of the job. When FS-135 is mounted: [Top Tray, Elevator Tray, Third Tray] When FS-231 is mounted: [Elevator Tray, Saddle Stack Tray] Received Time : Displays the time-of-day when the job was registered with the device. Job Complete Time : Displays the time-of-day when the job was completed. Data Type : Displays the output data format of the data.
130 8.
131 9. Troubleshooting 9.1 Unable to Print This chapter explains the troubleshooting procedures for possible malfunctions. Perform the troubleshooting procedures given below when the copier is unable to print even if you execute a print command from your PC. Symptom Possible Cause Action A message appears on the PC screen, saying something to the effect that “no printers are connected,” “no paper is loaded,” or “LPT1 write error.” An error is probably present in the copier.
132 9. Troubleshooting Symptom Continuation from previous page (Printing does not start despite the completion of printing setup on the PC.) Possible Cause Action The print job is locked. Check with the job list on the copier control panel to see if the print job in question is locked. If so, unlock it. The connection of the controller to the network is yet to be established. Consult the network administrator. If the copy track function is active, an illegal access number might have been entered.
133 9. Troubleshooting 9.2 Unable to Make Correct Settings / Unable to Print Exactly as Set Perform these troubleshooting procedures if you cannot make proper settings in the print driver or when the print results do not represent what has been set. MEMO Some of the printer driver functions cannot be combined with another. For details, see “Appendix C: Incompatible Function Combinations.” ☞p.194 Symptom Unable to select an item in the printer driver.
134 9. Troubleshooting Symptom The watermark cannot be printed. Possible Cause Action The watermark is not correctly set. Check the watermark setting. The watermark density is set to a low level. Check the “Shading” setting. Watermark may not be printed in graphics applications. No watermark can be printed in this case. Unable to specify Staple. No staple can be made if Media Type is Thick or Transparency. Check the setting for each item of the printer driver. Unable to staple.
135 9. Troubleshooting Symptom Possible Cause Action Check the setting for each item of the printer driver. Unable to specify Punch. Hole Punch cannot be specified together with Booklet, OHP, Thick2, and/or Thick3. Unable to effect Punch. Printed pages can at times Check the setting for be fed out without being Orientation. punched if the direction of the paper loaded in the paper source is not correct. The hole punch Orientation setting is not position is not what is correct. expected.
136 9. Troubleshooting Symptom Distribution Number cannot be specified. Possible Cause Action • Add the necessary options. To specify Distribution Number, an optional HDD • Select “HDD” for “Device Option.” and an optional 256-MB memory must be mounted on the copier. The function can be specified when “HDD” is added to “Device Option” of the printer driver.
137 Appendixes A. Product Information Item Detail CPU MPC8240-200 MHz RAM 32MB (on copier board) + 128MB (memory that comes with the controller) Printer Emulation PCL5c Host Interface IEEE1284 (Compatible, Nibble, ECP) Remark The copier CPU is used. USB (version 1.1) Ethernet 10Base-T, 100Base-TX Frame Type Ethernet 802.2 Ethernet 802.3 Ethernet II Ethernet SNAP Protocol TCP/IP IPX/SPX NetBEUI Compatible OS Windows 98, 98SE, Me, NT4.0, 2000, XP Compatible Browser Internet Explore 5.
138 Appendixes B. How to Use Network Management Utility Light What is Network Management Utility Light? Network Management Utility Light is a device management utility built into the controller. From a PC on the network, start a Web browser and access Network Management Utility Light. Then, controller settings can be changed. System Requirements Network : Ethernet + TCP/IP protocol Application : Web browser Microsoft Internet Explorer version 5.5 or later (Java-compliant), Netscape Communicator version 4.
139 Appendixes Initial Screen Components The screen that is displayed immediately after Network Management Utility Light has been accessed consists of the following components. This screen is generally referred to as the user mode screen and can be viewed by anyone. In addition, entering the specified number in “Administrator’s Code” on the user mode screen will allow you to enter the “Administrator Mode.” ☞p.
140 Appendixes (2) Tabs Displays the categories to be controlled by Network Management Utility Light. • System • Job • File • Print • Scan (3) Menu Displays information and settings in the selected tab. The menu items differ according the specific tab selected for use. (4) Information/setting display Displays the details of the menu selected. (5) Administrator’s Code Enter the administrator number to log on to the Administrator mode.
141 Appendixes Entering the Administrator Mode The operating mode can be switched between the User mode and Administrator mode. To make system settings, it is necessary to enter the Administrator mode. k4334P214CA Type the administrator password of the copier in the Administrator’s Code box and then click the “Log-in” button. This selects the Administrator mode screen. k4334P215CA To return to “User Mode,” click the “Log-out” button to exit from the Administrator mode.
142 Appendixes 1. User Mode Checking Copier Status • Checking Paper Source Status Display Procedure Click the “System” tab and then select “Detail” – “Input Tray.” Screen Description k4334P217CA Input Tray Paper Size (Standard sizes) (Nonstandard sizes) : Shows the names of the trays. Tray 1, Tray 2, Tray 3, Tray 4, LCT, Bypass Tray : Shows the size of the paper loaded. Display Lengthwise: A4 SEF Crosswise: A4 LEF : A3, A4, A5, A6, B4, B5, B6, 11×17, 11×14, Legal, Letter, 5.5×8.
143 Appendixes Paper Type Capacity Paper : Shows the type of the paper loaded. Normal, Thick 1, Thick 2, Thick 3, Envelope, Label, Post Card, OHP, Normal 2nd-Side, Thick 1 2nd-Side, Thick 2 2nd-Side, Thick 3 2nd-Side, Post Card Second Side For Duplex If paper attributes have been set, Normal (Specialty, etc.) will be displayed. Single Sided Only, High Quality Paper, Specialty : Shows the loading capacity of the cassette. The figure represents the maximum number of sheets of plain paper to be loaded.
144 Appendixes • Checking Exit Tray Status Display Procedure Click the “System” tab and then select “Detail” – “Output Tray.” Screen Description k4334P218CA Output Tray Capacity Paper : Shows the names of the trays of the option mounted on the copier. When FS-135 is mounted:Top Tray, Elevator Tray, Third Tray When FS-231 is mounted:Top Tray, Second Tray : Shows the loading capacity of the tray in terms of A4/Letter plain paper. : Shows the condition of each tray.
145 Appendixes • Checking Hard Disk Status Display Procedure Click the “System” tab and then select “Detail” – “Head Disk” Screen Description k4334P219CA Total Space System Resource User’s Resource Free Space : Shows the space available for use of the hard disk mounted in the copier. : Shows the space used by the system of the total hard disk space available. : Shows the space used by the user of the total hard disk space available.
146 Appendixes • Checking Network Status Display Procedure Click the “System” tab and then select “Detail” – “Interface Info” Screen Description k4334P220CA Interface Info Type IP Address MAC Address Local I/F Type : Shows the type of the network to be used. Ethernet 10Base-T/100Base-TX : Shows the IP address that has been set. : Shows the MAC address of the device. : Shows the local interface that can be used by the device.
147 Appendixes • Checking Consumables and Supplies Status Display Procedure Click the “System” tab and then select “Detail” – “Consumables” Screen Description k4334P221CA Imaging Unit (C) : Shows the information concerning each Imaging Unit. Ready, Near End of Life, End of Life Imaging Unit (M) : Shows the information concerning each Imaging Unit. Ready, Near End of Life, End of Life Imaging Unit (Y) : Shows the information concerning each Imaging Unit.
148 Appendixes Ready, Near End of Life, End of Life : Shows the information concerning the Fusing Unit. Ready, Near End of Life, End of Life Transfer Roller : Shows the information concerning the Transfer Roller Unit. Ready, Near End of Life, End of Life Image Transfer Belt Unit : Shows the information concerning the Image Transfer Belt Unit. Ready, Near End of Life, End of Life Toner Cartridge (C) : Shows the information concerning the Toner Cartridge of each color of toner.
149 Appendixes Meter Count • Meter Count Display Procedure Click the “System” tab and then select “Detail” – “Meter Count” Screen Description k4334P222CA Copy/Printer Copy Black counter : Shows the count of black copies of the copy output counter controlled by the copier. Copy Full Color counter : Shows the count of full color copies of the copy output counter controlled by the copier. Copy Mono Color counter: Shows the count of mono color copies of the copy output counter controlled by the copier.
150 Appendixes Copy + Printer Black counter: Shows the count of black copies and printed pages of the copy and printed output counter controlled by the copier. Copy + Printer Color counter: Shows the count of color copies and printed pages of the copy and printed output counter controlled by the copier. Total : Shows the grand total of the copy and printed output counter controlled by the copier.
151 Appendixes Online Support Information • Online Support Information Display Procedure Click the “System” tab and then select “Online Assistance” Screen Description k4334P239CA Contact : Shows the contact, to which you can direct your inquiries about the product. Contact Information Phone: Shows the phone number, at which you can call for information on the product. Internet Product Help : Shows the URL of the home page concerning the product.
152 Appendixes Print job list • Print job list Display Procedure Click the “Job” tab and then select “Active Job” – “Print” Screen Description k4334P183CA Job Name Status Job Type Detail button Delete button : Displays the User Name specified on the printer driver. : Indicates the status of the job. [Printing, Waiting, Printing Stopped, Printing Stopped (Error), Receiving, Job Stored, Job Locked] : Displays the printing method of the job.
153 Appendixes Destination : Displays the exit port of the job. When FS-135 is mounted: [Top Tray, Elevator Tray, Third Tray] When FS-231 is mounted: [Elevator Tray, Saddle Stack Tray] File Name : Displays the name of the job. Number of Pages : Displays the number of pages per one copy set of the job. Copy : Displays the number of copies produced for the job. Delete button : Clicking this button will delete the job.
154 Appendixes • Scanner job list Display Procedure Click the “Job” tab and then select “Active Job” – “Scan” Screen Description k4334P229CA Status : Indicates the status of the job. [Scanning, Scanning Stopped, Separate Scanning Stopped, Scanning Stopped (Error), Transfering] Job Type : Displays the type of the job.
155 Appendixes • Print job history Display Procedure Click the “Job” tab and then select “Job History” – “Print” Screen Description k4334P184CA Result : Displays the result of execution of the job. [Job Completed, Job Deleted by Error, Job Deleted by User, Staple Canceled, Punch Canceled, Paper Fold Canceled] Job Name : Indicates the name of the user who has issued the job. File Name : Displays the name given to the job. Number of Pages: Displays the number of pages per one copy set of the job.
156 Appendixes Destination : Displays the exit port of the job. When FS-135 is mounted: [Top Tray, Elevator Tray, Third Tray] When FS-231 is mounted: [Elevator Tray, Saddle Stack Tray] Received Time : Displays the time-of-day when the job was registered with the device. Job Complete Time : Displays the time-of-day when the job was completed. Data Type : Displays the output data format of the data.
157 Appendixes • Scanner job history Display Procedure Click the “Job” tab and then select “Job History” – “Scan” Screen Description k4334P230CA Result Job Type Destination Number of Pages Detail button : Displays the result of execution of the job. [Job Completed, Job Deleted by Error, Job Deleted by User] : Displays the method of delivery for the job.
158 Appendixes File • User Directory Display Procedure Click the “File” tab and then select “User Directory.” Screen Description k4334P185CA HDD directories : Click to display a list of files contained in the directory. A password is necessary for all but PUBLIC. (8 alphanumeric characters or less) “Create” button : Selecting an unused directory and clicking “Create” will display the “Create HDD Directories” registration screen.
159 Appendixes • Fil list Display Procedure Click the “File” tab and then select “User Directory” Screen Description k4334P186CA Data list screen File Name Received Time File Size : Displays the name of the file stored in the HDD directories. : Displays the time-of-day when the file was stored in the HDD directories. : Displays the size of the file stored in the HDD directories. Buttons Acquire Selected File : Downloads the selected file in the PC.
160 Appendixes • External server link status Display Procedure Click the “File” tab and then select “External Server Link” Screen Description k4334P231CA Server Address : Displays the FTP server, which has been set “ON” to “External Server Link,” of all the FTP servers registered in the Administrator mode. Double-clicking the address will allow you to access the FTP server. NOTE In the “External Server Link” function, the FTP server is accessed by the authority of “anonymous.
161 Appendixes Print • Setting Printer Display Procedure Click the “Print” tab and then select “Default Set” – “Setting” Screen Description k4334P169CA Paper Size Setting values Input Tray Setting values Orientation Setting values : Select the default paper size selected when the controller receives a print job that does not specify any specific paper size.
162 Appendixes Output Setting values Copy Setting values : Select the default double-sided print function selected when a device receives a print job that does not specify any specific double-sided print function. : Single Sided, Long Edge Binding, Short Edge Binding : Select the default setting of the number of copies selected when a device receives a print job that does not specify any specific number of copies.
163 Appendixes • PCL Setting Display Procedure Click the “Print” tab and then select “Default Set” – “PCL Setting” Screen Description k4334P170CA Font Number Setting values Symbol Set Line/Page Setting values Font Size Unit Setting values Font Size (Scalable Font) Setting values Font Size (Bit Map Font) Setting values Override Setting values : : : : : : : : : : : : Set the default font number. 0 to 45 Set the default symbol set. Set the default number of lines per page.
164 Appendixes • Font Information Display Procedure Click the “Print” tab and then select “Font Information” Screen Description k4334P232CA Show the PCL font List.
165 Appendixes • Report Type Display Procedure Click the “Print” tab and then select “Report Type” Screen Description k4334P233CA Configuration PCL Demo Page PCL Font List Print Button : Insert a check mark into the box to print the printer controller setup page. : Insert a check mark into the box to print the PCL demo page. : Insert a check mark into the box to print the PCL font list. : Click this button to execute a test print operation.
166 Appendixes Scan • One Touch Key Registration Display Procedure Click the “Scan” tab and then select “One Touch Key Registration” Screen Description k4334P188CA Index name Job Type : Displays the name of the index set. It can be selected and renamed. : An icon corresponding to the job type registered is displayed. Scan To E-mail icon File (Scan To PC/FTP Server) icon File (Scan To HDD) icon Scan To Internet Fax icon – Icon not registered Destination Name : Displays the destination name registered.
167 Appendixes • One Time Registration Display Procedure Click the “Scan” tab and then select “One Time Registration” Screen Description k4334P190CA Job Type : An icon corresponding to the job type registered for one time registration is displayed. Scan To E-mail icon File (Scan To PC/FTP Server) icon File (Scan To HDD) icon Scan To Internet Fax icon – Icon not registered Destination Name : Displays the destination name registered for one time registration.
168 Appendixes 2. Administrator Mode System • User’s Choice 1 Display Procedure Click the “System” tab and then select “User’s Choice” – “User’s Choice1” Screen Description k4334P215CA Date/Time Set Memory Recall : Set the date and time-of-day. : Set the memory recall function. Setting values: Yes, No Auto Panel Reset : Set the auto panel reset function of the copier. Setting values : Yes, No Auto Panel Reset Time : Set the time for the auto panel reset function of the copier.
169 Appendixes Auto Clear Mode Setting values : If “Yes” is set, the copier determines, when the optional Plug-In Counter or the magnetic card of the Data Controller is removed, that a new user is about to use it, thus clearing the settings.
170 Appendixes • User’s Choice 2 Display Procedure Click the “System” tab and then select “User’s Choice” – “User’s Choice2.” Screen Description 4334P224CA Priority Exit Tray (Copy) (Print) (Internet Fax) Intelligent Sorting Setting values Criss Cross Sort Setting values Priority Device Setting values : Set the exit tray that is given priority when FS-135 is mounted.
171 Appendixes 2in1/4in1/Booklet Copy Zoom: Set the function that automatically selects the zoom ratio when 2in1 or 4in1 is selected. Setting values : Yes, No Sleep : Set the Sleep function. Setting values : Yes, No Screen Pattern : Set the screen pattern for PC print output.
172 Appendixes • Setting the Browser Display Procedure Click the “System” tab and then select “Preference” Screen Description k4334P216CA Refresh Rate Setting value Language Setting values : Set the screen refresh rate of Network Management Utility Light. : 30 to 7200 (sec.) : Set the display language of Network Management Utility Light.
173 Appendixes • Online Support Function Display Procedure Click the “System” tab and then select “Online Assistance.” Screen Description k4334P225CA Contact : Types the contact, to which you can direct your inquiries about the product. Contact Information Phone: Types the phone number, at which you can call for information on the product. Internet Product Help : Types the URL of the home page concerning the product. Corporate Web Site : Types the URL of the home page of the manufacturer.
174 Appendixes File • User Directory Display Procedure Click the “File” tab and then select “User Directory.” Screen Description k4334P240CA Data list screen File Name Received Time File Size : Displays the name of the file stored in the HDD directories. : Displays the time-of-day when the file was stored in the HDD directories. : Displays the size of the file stored in the HDD directories. Buttons Acquire Selected File : Downloads the selected file in the PC.
175 Appendixes • HDD File Life Display Procedure Click the “File” tab and then select “File Storage Life.” Screen Description k4334P234CA File Storage Life Setting value Apply Button Clear Button : Specify the period of storage of files in the hard disk. (Valid only with files saved in the hard disk through Scan to HDD) : No File Time Limitation, 1 day, 2 day, 3 day, 4 day, 5 day, 6 day, 7day : Fixes the setting. : Cancels the setting.
176 Appendixes Print • Local Interface Setting Display Procedure Click the “Print” tab and then select “Local I/F.” Screen Description k4334P226CA Parallel Interface Setting values I/O Timeout Setting value : : : : Set the communication method. Compatible, Nibble, ECP Set the communication timeout. 10 to 300 (sec.
177 Appendixes • IPP Setting Display Procedure Click the “Print” tab and then select “IPP.” Screen Description k4334P154CA Printer Name : Type in a name to identify the printer during IPP printing. Printer Local : Type in the location of the printer. Printer Manufancturer and Model: Type in the printer manufancturer name and model name.
178 Appendixes Scan • Setting the File Format Display Procedure Click the “Scan” tab and then select “Scan” Screen Description k4334P171CA • Scan Device Name : The characters set for this parameter is appended before the name of the image file created with the scan function. Setting value : 36 alphanumeric characters or less Color/Grayscale Compression Level: Select the compression level for images.
179 Appendixes NetWork • TCP/IP Setting Display Procedure Click the “Network” tab and then select “Common Setting” – “TCP/IP” Screen Description k4334P153CA IP Address Subnet Mask Gateway Address RAW Port Number DHCP : Set the IP address of the controller. : Set the subnet mask for the network to be connected. : Set the default gateway address for the network to be connected. : default value 9100 : Set use of DHCP server.
180 Appendixes • IPP Setting Display Procedure Click the “Network” tab and then select “Common Setting” – “IPP.” Screen Description k4334P235CA Enable IPP Setting values Accept IPP Jobs Setting values Printer URI Operational Supported Setting values : : : : : Set the IPP function. Enable, Disable Set the IPP reception function. Enable, Disable Displays the URL of the printer, with which data can be printed using IPP. : Specify the print operation supported by the IPP.
181 Appendixes • NetWare Setting Display Procedure Click the “Network” tab and then select “Common Setting” – “NetWare Configuration.” Screen Description k4334P155CA Enable NetWare Setting values Frame Type Setting values Bindery/NDS Setting values Print Server Name Setting value Print Server Password Setting value Preferred File Server Setting value Preferred NDS Context Setting value : : : : : : : : : : : : : : Set the NetWare printing. Enable, Disable Set the frame type. Auto Detect, II, 802.2, 802.
182 Appendixes Preferred NDS Tree Setting value Print Queue Scan Rate Setting value Mode Setting value Printer Number Setting value : Set the preferred NDS tree name for NetWare. : 63 alphanumeric characters or less : Set the print queue scan rate for NetWare. The default value is 1 sec. : 1 to 65535 sec. : Set the mode for NetWare. : PServer, Nprinter/Rprinter : Set the printer number for NetWare. The number is assigned automatically if it is 255.
183 Appendixes • NetWare Status Display Procedure Click the “Network” tab and then select “Common Setting” – “NetWare Status.” Screen Description k4334P236CA NetWare Server Queue Name Queue Status : Displays the NetWare server name. : Displays the queue name of the NetWare server. : Displays the queue status of the NetWare server.
184 Appendixes • Windows Printing Setting Display Procedure Click the “Network” tab and then select “Common Setting” – “Windows Configuration.” Screen Description k4334P156CA Enable Windows Printing Service: Set the Windows printing service. Setting values : Enable, Disable NetBIOS Name : Set the NetBIOS name. Setting value : 15 alphanumeric characters or less Printing Service Name : Set the printing service name.
185 Appendixes • E-mail/Internet FAX Reception Setting Display Procedure Click the “Network” tab and then select “E-mail/Internet FAX” – “Receive.” Screen Description k4334P176CA POP3 Server POP3 Login Name Setting value POP3 Password : : : : Set the IP address of the POP3 server. Set the logon name of the POP3 server. 63 alphanumeric characters Set the password used when logging on to the POP3 server.
186 Appendixes • E-mail/Internet FAX Transmission Setting Display Procedure Click the “Network” tab and then select “E-mail/Internet FAX” – “Send.” Screen Description 4334P175CA SMTP Server Port Number : Set the IP address of the SMTP server. : Set the port number of the SMTP server. (The default value of “25” is generally used.) SMTP Connection Timeout : Set the communications timeout with the SMTP server. Setting values : 30 to 300 sec.
187 Appendixes • Setting the Mail Options Display Procedure Click the “Network” tab and then select “E-mail/Internet FAX” – “E-mail.” Screen Description k4334P177CA Subject Setting value Description Setting value : : : : Type the title of the e-mail. 64 characters Type the message of the e-mail.
188 Appendixes • Setting the Internet FAX Options Display Procedure Click the “Network” tab and then select “E-mail/Internet FAX” – “Internet FAX.” Screen Description k4334P178CA Subject Setting value Description Setting value : : : : Type the title of the e-mail. 64 characters Type the message of the e-mail.
189 Appendixes • Setting for Printing E-mail/Internet FAX Display Procedure Click the “Network” tab and then select “E-mail/Internet FAX” – “Print.” Screen Description k4334P179CA Text Print Setting values Internet Fax Print Setting values : Set whether to print an E-mail message received by the copier. : Enable, Disable : Set the magnification for printing of received data. : Full Size, Reduced (default), A4/Letter Full Size: The received data is printed in full size.
190 Appendixes • Setting the (Proxy) FTP Server Display Procedure Click the “Network” tab and then select “FTP Server” – “FTP Server Configuration.” Screen Description k4334P174CA Proxy IP Address : When a proxy server is to be used, set the IP address of the proxy server. Port Number : Set the port number of the proxy server. (The default value of “21” is generally used.) FTP Connection Timeout : Set the communications timeout with the FTP server. Passive Mode : Set the Passive Mode.
191 Appendixes • Registering FTP Servers Display Procedure Click the “Network” tab and then select “FTP Server” – “FTP Server Registration.
192 Appendixes IP Address Login Name Setting value Password Setting value Port Number Directory Setting value Use Proxy Setting values External Server Link Setting values : Specify the IP address of the FTP server. : Specify the name with which to log on to the FTP server. : 32 alphanumeric characters or less : Specify the password with which to log on to the FTP server. : 64 alphanumeric characters or less : Specify the port number of the FTP. (The default value of “21” is generally used.
193 Appendixes • TWAIN Setting Display Procedure Click the “Network” tab and then select “TWAIN Coufiguration” Screen Description k4334P180CA Operation Lock Time Setting values : Set the operation lock time of the control panel to enable TWAIN operations from the PC. : 30 to 300 sec.
194 Appendixes C.
195 Appendixes ■ Limitation between Paper Size and Functions × × × × × × × × × × × × Blank : selectable combination × : not selectable combination × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × Top side 2 Points Left side 2 Points Staple Auto 2 Points Corner × Crease + Center Staple Corner N-up Booklet Duplex Staple × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × ×
196 Appendixes Add the following Options in the column “Installed Options” by depressing “Device Option Setting” Tab, and the function(s) shown in the right columns can be selected.
197 INDEX INDEX A Administrator Mode 141 B Booklet Printing 54 C Connecting the Network Cable Cover 5 58 D Duplex Printing Duplex/Booklet Printing 54 54 E Easy Set Energy Save Mode Time 45 168 G Gateway Address 18, 179 H HDD directories 79 I IEEE1284 (Centronics) Cable Installation through Plug and Play Installing the Printer Driver Interleaf (OHP Interleaving) Internet Fax IP Address IP Address Setting IPP (Internet Printing Protocol) 15 15 7 58 94 18, 179 18 23 L Lock Job 121, 123 N Net
198 INDEX O One Time Registration One-Touch Key Registration Operating Environment 115 110 1 P Printer Figure Printing Pages with Watermarks Proof and Print Public directory 45 50 121, 124 79 R Registering FTP Servers 70 S Scan to E-mail Scan to FTP Server Scan to HDD Scan to PC Scanned File Separation Setting the Proxy Server Store to HDD Store to Memory Subnet Mask 86 69 77 64 62, 178 73 121, 124 121, 125 18, 179 T TWAIN 106, 107 U Uninstalling the Driver USB Cable User directory 41 15 158
Thank you very much for purchasing the Konica IP-711 Print Controller. This User's Manual includes instructions for making prints, correct handling of the machine, and precautions for safety. Please read this manual before printing. In order to maintain a satisfactory printing performance, please keep this User's Manual readily available for reference. COPYRIGHT © 2002 by Konica Business Technologies, Inc. MANUAL PART NUMBER: OP-IP711-01 WABSITE ADDRESS: http://www.konicabt.
MANUFACTURER KONICA CORPORATION TOKYO JAPAN 2002.
