SAS-IPCAM115 MANUAL IP CAMERA
ENGLISH Table of contents • Introduction: • Safety precautions: • Packaging content: • System requirements: • Product description: • User instructions: • Maintenance: • Warranty: • Disclaimer: • Disposal: Introduction: The plug-and-play IP camera enables people to watch over their properties. It is easy to set up and requires no complex configuration.
ENGLISH Product description: 1. 2. 3. 4. 5. 6. 7. 8. Mount Microphone Antenna IR LED for night vision Camera lens Light intensity sensor WPS/RESET button (behind rubber cover) 12V power cord User instructions: A. Hardware Installation 1. Please find a location to install uCare Cam that is within good WiFi signal reach of your home Router. 2. If you plan to hang the uCare Cam, you can use the included mounting kit found in inside box. 3.
ENGLISH B. Hardware Installation 1. Download the Smartphone APP “uCare Cam” from App store(iOS) or Play Store (Android). 2. Search for APP name “uCare Cam”, then download and install it into Smartphone. 3. After the software installation is complete, the icon will appear . Click on this to run the APP. C. uCare Cam APP Overview Default camera password: Default manager name: Default manager password: 0000 admin 0000 There are 4 major function Tabs at the bottom of the APP main screen.
ENGLISH User will need to input a management ID and Password to enter this Tab. Default management ID: admin Default Password: 0000 If you forget your password, you can reset the uCare Cam by pressing the WPS/REST button at the back of the camera for 10 seconds. This will restore uCare Cam to factory settings. You will need to set up the WiFi connection again after you reset the camera. D.
ENGLISH 1. Make sure the status LED on uCare Cam is blinking Red and Green. If the status LED is not blinking Red and Green, please press and hold the WPS/REST button for 10 seconds to reset uCare Cam. Wait for 1-2 minutes for it to restart and the LED should become Red and Green. 2. Connect your iOS device to the router inside uCare Cam. To 3. 4. 5. 6. 7. 8. , then connect to uCare Cam router, open up “Settings” “Wi-Fi” and let it search for network. The network will be “wificam-p2p”.
ENGLISH your Router supports WPS is to look for a button that says “WPS” on the Router. It may also be called “AOSS” or “QSS”. 1. Press and hold the WPS/REST button for 10 seconds at the back of the camera. It will reset and restart the uCare Cam. After about 60 seconds, the LED color should flash Green and Red. 2. Press “WPS” button on WiFi Router. 3. Press the WPS/REST Button on the back of the uCare Cam for 2 seconds.
ENGLISH 7. Please enter a Camera name (2 to 20 characters) and default password “0000”. You are encouraged to change the default password after setup for security purposes. Then click “OK” in the top right corner. 8. The camera will restart and the Smartphone App will automatically connect to the camera in Live View. 9. When uCare Cam successfully connects to your Router, the status LED color will turn Orange. It may take up to 10 minutes.
ENGLISH Method 2: Scan QR Code at back of uCare Cam 1. Make sure your Smartphone is connected to the internet. Open up the Smartphone APP 2. 3. 4. 5. “uCare Cam” and click on the “+” at the top right of the screen. Click on “Scan camera QR code”. You will see your Smartphone camera live view. Face your Smartphone camera towards the QR code found on the back of uCare Cam. Please make sure the QR code is clear and fully viewable in the screen.
ENGLISH Method 1: Scan for uCare Cam in local intranet 1. Make sure your Smartphone is connected to the same Router as your uCare Cam. Open up the Smartphone APP “uCare 2. 3. 4. 5. 6. and click on the “Click here to import installed Cam” WiFiCam” at the top of the screen. Click on “Search”. You will see a list of UID’s that were found on your local intranet (Figure XX). Click on the UID you would like to add. Please enter a Camera name (2 to 20 characters) and the camera password.
ENGLISH 2. Click in the “UID” field to enter typing mode. 3. Type in 20 digit code exactly as printed underneath the QR code in back of uCare Cam. 4. Please enter a Camera name (2 to 20 characters) and the camera password. Default password is 0000. Click “OK” on the bottom of the screen. 5. You will see the Camera name now in Camera List view. It should indicate that the Camera is “Online”. To connect to the Camera, please click on Camera name.
ENGLISH Typical scenario will be that the uCare Cam is installed at home or in the office and the Smartphone has a 3G/3.5G/4G internet connection. Typical frame rate will be around VGA 640x480 10~15fps. 3) Relay Mode uCare Cam and Smartphone cannot establish a point to point network connection link. uCare Cam must send Audio/Video data to a Relay Server and the Smartphone will retrieve data from the Relay server. In Relay mode, there will be a limit on the Video download frame rate.
ENGLISH Take Photo Connection Status Information Playlist User can view, delete, and copy picture files.
ENGLISH File delete Photo view Settings Manage uCare Cam (Default manager name: admin , Default Password: 0000 ) Only one User can manage a camera that is online and connected to Smartphone APP at any one time.
ENGLISH 1) Change WiFi Router User can remotely switch the camera to connect to a different WiFi Router. 2) Alert & Notify Setting / Warning & Notify Setting The camera has a number of hardware alarm detection possibilities. User can set the desired trigger and notification. When a new event is generated, the APP will notify the User either through email or through a Phone Push Message.
ENGLISH Set Email Alerts To setup your email to receive motion/sound/etc. alerts, please login to the “Settings” page with Manager name and password (default: admin / 0000). 1) Click on “Alert & Notify Setting” or “Warning & Notify Setting”. 2) Click on “Email snapshot alert” 3) You will see a variety of options. You can touch and scroll down the page to see more options.
ENGLISH • • SMTP Mail Settings – only either SMTP or Gmail mail settings can be set. Please enter your email provider’s SMTP server settings. You may need to contact your email provider for the server settings. Please enter your email address and email password. This account will be used as the “Sender” or “From” for the email alerts. Gmail Mail Settings – only either SMTP or Gmail mail settings can be set. For convenience, we have already entered Gmail’s SMTP server settings.
ENGLISH 4) SD Card Recording Setting User can insert a microSD card into the camera to enable the recording function. Trigger Recording: The camera will automatically start recording when a trigger event (motion, sound, and other events) have occurred. The camera will record for 60 seconds. If another trigger event occurs, the camera will record for another 60 seconds; otherwise it will stop recording. Continuous Recording: User can setup uCare Cam to constantly record.
ENGLISH 6) Password Setting The two-level password management system allows the user to safely and effectively manage the camera. First layer: Camera password – able to view the camera. Default value is 0000 Second layer: Manager’s Name and Password – able to view and set uCare Cam settings. Default value : admin / 0000 7) Date & Time User can only adjust the Time Zone. The Date and Time will be set from the factory and User can not change.
ENGLISH J. 1. 2. 3. 4. 5. 6. 7. Update your uCare Cam firmware Download firmware and un-compress the file. Copy “update.bin” to microSD Card top folder, for example H:\ Turn off power to uCare Cam and insert microSD card into uCare Cam microSD slot in back of uCare Cam. Turn power on to uCare Cam. uCare Cam will start reading data from microSD card and upgrade the firmware. LED color will blink Red and Green during this process. It will take about 3 minutes to upgrade the firmware.
ENGLISH 2) The live video stream is very slow. uCare cam will automatic adjust video streaming speed according to smartphone’s internet connection. It will start sending video from a low frame rate and gradually increase the frame rate. It may take 1-2 minutes for the frame rate to stabilize. If performance is still not satisfactory – a. Please ensure motion detection is turned off. “Settings” -> “Alert & Notify Setting” -> “Email snapshot alert” -> “Motion detection enabled” is NOT checked. b.
ENGLISH 7) Why can’t uCare Cam connect with WiFi Router using WPS Mode? a. Make sure Router’s WPS function is enabled. b. Please try Router model if WPS mode setup failed. 8) What is the frequency of email alert and smartphone notify alert? Ans: Once motion or sound detection is triggered, then uCare Cam will send email and phone notify immediately. If the trigger event continually happens, then the email and phone notify will send out on a three minute interval.
ENGLISH Maintenance: Clean the product only with a dry cloth. Do not use cleaning solvents or abrasives. Warranty: Any changes and/or modifications to the product will void the warranty. We cannot accept any liability for damage caused by incorrect use of this product. Disclaimer: Designs and specifications are subject to change without notice. All logos, brands and product names are trademarks or registered trademarks of their respective holders and are hereby recognized as such.
