AT8904M CLI Reference Manual AdvancedTCA M5305_TECH_2 1.
AT8904M Preface Revision History Publication Title: ID Number: Rev. Index AT8904M CLI Reference Manual M5305_TECH_2 Brief Description of Changes Date of Issue 1.00 Initial Issue 2007-04-20 1.01 Added new commands, editorial changes 2007-04-20 1.02 First version for AT8901M 2007-05-08 1.03 First version for AT8902M 2007-05-08 1.04 Added commands for Port channel, LAG and multicast for AT8901M, AT8902M and AT8904M 2007-11-06 1.
AT8904M Table of Contents Table of Contents Revision History .........................................................................................................ii Imprint ........................................................................................................................ii Disclaimer ..................................................................................................................ii Table of Contents ................................................................
Table of Contents AT8904M 2.1 Port Configuration Commands ................................................................2 - 2 2.1.1 interface ..........................................................................................2 - 2 2.1.2 auto-negotiate .................................................................................2 - 2 2.1.3 auto-negotiate all .............................................................................2 - 3 2.1.4 description ....................................
AT8904M Table of Contents 2.3.9 vlan participation all ...................................................................... 2 - 20 2.3.10 vlan port acceptframe all ............................................................... 2 - 20 2.3.11 vlan port ingressfilter all ................................................................ 2 - 20 2.3.12 vlan port pvid all ............................................................................ 2 - 21 2.3.13 vlan port tagging all ...........................
Table of Contents AT8904M 2.9.1 set gmrp adminmode ....................................................................2 - 35 2.9.2 set gmrp interfacemode ................................................................2 - 36 2.9.3 show gmrp configuration ...............................................................2 - 36 2.9.4 show mac-address-table gmrp ......................................................2 - 37 2.10 Port-Based Network Access Control Commands ..................................
AT8904M Table of Contents 2.12.4 deleteport (Global Config) ............................................................. 2 - 53 2.12.5 port-channel static ........................................................................ 2 - 53 2.12.6 port lacpmode ............................................................................... 2 - 53 2.12.7 port lacpmode all .......................................................................... 2 - 54 2.12.8 port-channel adminmode .............................
Table of Contents AT8904M 2.17.3 lldp timers ......................................................................................2 - 68 2.17.4 lldp transmit-tlv ..............................................................................2 - 68 2.17.5 lldp transmit-mgmt .........................................................................2 - 69 2.17.6 lldp notification ...............................................................................2 - 69 2.17.7 lldp notification-interval ...........
AT8904M Table of Contents 3.1.12 show arp switch .............................................................................. 3 - 6 3.2 IP Routing Commands ............................................................................ 3 - 6 3.2.1 routing ............................................................................................. 3 - 6 3.2.2 ip routing ......................................................................................... 3 - 7 3.2.3 ip address .........................
Table of Contents AT8904M 3.6.2 bootpdhcprelay enable ..................................................................3 - 22 3.6.3 bootpdhcprelay maxhopcount .......................................................3 - 23 3.6.4 bootpdhcprelay minwaittime ..........................................................3 - 23 3.6.5 bootpdhcprelay serverip ................................................................3 - 23 3.6.6 show bootpdhcprelay ...............................................................
AT8904M Table of Contents 3.7.41 show ip ospf .................................................................................. 3 - 37 3.7.42 show ip ospf abr ............................................................................ 3 - 38 3.7.43 show ip ospf area .......................................................................... 3 - 39 3.7.44 show ip ospf database .................................................................. 3 - 40 3.7.45 show ip ospf database database-summary ..........
Table of Contents AT8904M 4.1.8 show classofservice ip-precedence-mapping .................................4 - 5 4.1.9 show classofservice ip-dscp-mapping .............................................4 - 5 4.1.10 show classofservice trust ................................................................4 - 6 4.1.11 show interfaces cos-queue .............................................................4 - 6 4.2 Differentiated Services (DiffServ) Commands .........................................4 - 6 4.2.
AT8904M Table of Contents 4.6.4 show diffserv service .................................................................... 4 - 22 4.6.5 show diffserv service brief ............................................................ 4 - 22 4.6.6 show policy-map interface ............................................................ 4 - 23 4.6.7 show service-policy ....................................................................... 4 - 23 4.7 MAC Access Control List (ACL) Commands ..............................
Table of Contents AT8904M 5.3 System Information and Statistics Commands ........................................5 - 6 5.3.1 show arp switch ...............................................................................5 - 6 5.3.2 show eventlog .................................................................................5 - 6 5.3.3 show hardware ................................................................................5 - 6 5.3.4 show version ....................................................
AT8904M Table of Contents 5.5.6 clear port-channel ......................................................................... 5 - 25 5.5.7 clear traplog .................................................................................. 5 - 25 5.5.8 clear vlan ...................................................................................... 5 - 25 5.5.9 clear board event-log .................................................................... 5 - 25 5.5.10 enable passwd ................................
Table of Contents AT8904M 5.8.19 ip dhcp bootp automatic ................................................................5 - 38 5.8.20 ip dhcp conflict logging ..................................................................5 - 39 5.8.21 clear ip dhcp binding .....................................................................5 - 39 5.8.22 clear ip dhcp server statistics ........................................................5 - 39 5.8.23 clear ip dhcp conflict ........................................
AT8904M Table of Contents 6.1.2 serviceport ip .................................................................................. 6 - 2 6.1.3 serviceport protocol ........................................................................ 6 - 3 6.1.4 network parms ................................................................................ 6 - 3 6.1.5 network protocol ............................................................................. 6 - 3 6.1.6 network mac-address ............................
Table of Contents 6.6.3 6.6.4 6.6.5 6.6.6 6.6.7 6.6.8 6.6.9 6.6.10 6.6.11 6.6.12 6.6.13 6.6.14 6.6.15 6.6.16 6.6.17 6.6.18 6.6.19 6.6.20 6.6.21 6.6.22 AT8904M snmp-server community ipaddr .....................................................6 - 16 snmp-server community ipmask ...................................................6 - 17 snmp-server community mode ......................................................6 - 17 snmp-server community ro ............................................................
AT8904M Table of Contents 6.10.3 script delete .................................................................................. 6 - 32 6.10.4 script list ........................................................................................ 6 - 33 6.10.5 script show .................................................................................... 6 - 33 6.10.6 script validate ................................................................................ 6 - 33 6.
Table of Contents AT8904M CLI Reference Manual AT8904M xx
AT8904M Preface About This Book This document describes configuration commands for FASTPATH® software. The commands can be accessed from the CLI. Why the Document was Created This document was created primarily for system administrators configuring and operating a system using FASTPATH software. It is intended to provide an understanding of the configuration options of FASTPATH software.
Preface AT8904M Trademarks © 2005 LVL7 Systems, Inc. All rights reserved. FASTPATH® and MasterDriver® are registered trademarks, and LVL7™ and the LVL7 logo are trademarks of LVL7 Systems, Inc. All other trademarks are the property of their respective owners. Kontron Modular Computers GmbH and the Kontron Logo are trade marks owned by Kontron Modular Computers GmbH, Kaufbeuren (Germany).
AT8904M Preface Explanation of Symbols CE Conformity This symbol indicates that the product described in this manual is in compliance with all applied CE standards. Please refer also to the section “Applied Standards” in this manual. Caution, Electric Shock! This symbol and title warn of hazards due to electrical shocks (> 60V) when touching products or parts of them.
Preface AT8904M High Voltage Safety Instructions Warning! All operations on this device must be carried out by sufficiently skilled personnel only. Caution, Electric Shock! High voltages are present inside the chassis when the unit’s power cord is plugged into an electrical outlet. Turn off system power, turn off the power supply, and then disconnect the power cord from its source before removing the chassis cover. Turning off the system power switch does not remove power to components.
AT8904M Preface General Instructions on Usage In order to maintain Kontron’s product warranty, this product must not be altered or modified in any way. Changes or modifications to the device, which are not explicitly approved by Kontron Modular Computers GmbH and described in this manual or received from Kontron’s Technical Support as a special handling instruction, will void your warranty.
Preface AT8904M Kontron provides for repair or replacement of any part, assembly or sub-assembly at their own discretion, or to refund the original cost of purchase, if appropriate. In the event of repair, refunding or replacement of any part, the ownership of the removed or replaced parts reverts to Kontron Modular Computers GmbH, and the remaining part of the original guarantee, or any new guarantee to cover the repaired or replaced items, will be transferred to cover the new or repaired items.
AT8904M Chapter 1 Using the Command-Line Interface Page 1 - 1 AT8904M CLI Reference Manual
Using the Command-Line Interface 1. AT8904M Using the Command-Line Interface The command-line interface (CLI) is a text-based way to manage and monitor the system. You can access the CLI by using a direct serial connection or by using a remote logical connection with telnet or SSH. This chapter describes the CLI syntax, conventions, and modes. It contains the following sections: • • • • • • • 1.1 1.1 “Command Syntax” on page 1 - 2 1.2 “Command Conventions” on page 1 - 2 1.
AT8904M Using the Command-Line Interface The parameters for a command might include mandatory values, optional values, or keyword choices. Table 1 describes the conventions this document uses to distinguish between value types. Table 1. Parameter Conventions Symbol 1.2.1 Example Description <> angle brackets Indicates that you must enter a value in place of the brackets and text inside them.
Using the Command-Line Interface AT8904M Table 2. Parameter Descriptions Parameter 1.3 Description Interface or slot/port Valid slot and port number separated by forward slashes. For example, 0/1 represents slot number 0 and port number 1. Logical Interface Represents a Logical slot and port number.. This is applicable in the case of a port-channel (LAG). You can use the logical slot/port to configure the port-channel.
AT8904M 1.4 Using the Command-Line Interface Using the “No” Form of a Command The no keyword is a specific form of an existing command and does not represent a new or distinct command. Almost every configuration command has a no form. In general, use the no form to reverse the action of a command or reset a value back to the default. For example, the no shutdown configuration command reverses the shutdown of an interface.
Using the Command-Line Interface AT8904M Table 5. CLI Command Modes Command Mode Prompt Mode Description Line Config Switch (line)# Allows you to configure various telnet settings and the console interface. Policy Map Config Switch (Config-policy-map)# Allows you to access the QoS Policy-Map configuration mode to configure the QoS Policy-Map. Policy Class Config Switch (Config-policy-class-map)# Consists of class creation, deletion, and matching commands.
AT8904M Using the Command-Line Interface Table 6. CLI Mode Access and Exit Command Mode Global Config Exit or Access Previous Mode Access Method From the Privileged EXEC mode, enter configure. VLAN Config Interface Config From the Privileged EXEC mode, enter vlan database. To exit to the Privileged EXEC mode, enter exit, or press Ctrl-Z. From the Global Config mode, enter To exit to the Global Config mode, enter exit. To return to the Privileged EXEC mode, enter Ctrl-Z.
Using the Command-Line Interface 1.5.1 AT8904M Command Completion and Abbreviation Command completion finishes spelling the command when you type enough letters of a command to uniquely identify the command keyword. Once you have entered enough letters, press the SPACEBAR or TAB key to complete the word. Command abbreviation allows you to execute a command when you have entered there are enough letters to uniquely identify the command.
AT8904M Using the Command-Line Interface Table 8. CLI Editing Conventions Key Sequence 1.6 Description Ctrl-Y Prints last deleted character Ctrl-Q Enables serial flow Ctrl-S Disables serial flow Ctrl-Z Return to root command prompt Tab, Command-line completion Exit Go to next lower command prompt ? List available commands, keywords, or parameters Using CLI Help Enter a question mark (?) at the command prompt to display the commands available in the current mode.
Using the Command-Line Interface 1.7 AT8904M Accessing the CLI You can access the CLI by using a direct console connection or by using a telnet or SSH connection from a remote management host. For the initial connection, you must use a direct connection to the console port. You cannot access the system remotely until the system has an IP address, subnet mask, and default gateway.
AT8904M Chapter 21 Switching Commands Page 2 - 1 AT8904M CLI Reference Manual
Switching Commands 2. AT8904M Switching Commands This chapter describes the switching commands available in the CLI. The Switching Commands chapter includes the following sections: • • • • • • • • • • • • • • • • • • 2.1 “Port Configuration Commands” on page 2 - 2 2.2 “Spanning Tree Protocol (STP) Commands” on page 2 - 6 2.3 “VLAN Commands” on page 2 - 17 2.4 “Double VLAN Commands” on page 2 - 27 2.5 “Provisioning (IEEE 802.1p) Commands” on page 2 - 29 2.6 “Protected Ports Commands” on page 2 - 30 2.
AT8904M Switching Commands Mode 2.1.2.1 Interface Config no auto-negotiate This command disables automatic negotiation on a port. NOTE: Automatic sensing is disabled when automatic negotiation is disabled. 2.1.3 Format no auto-negotiate Mode Interface Config auto-negotiate all This command enables automatic negotiation on all ports. 2.1.3.1 Default enabled Format auto-negotiate all Mode Global Config no auto-negotiate all This command disables automatic negotiation on all ports. 2.1.
Switching Commands 2.1.6 AT8904M Format no mtu Mode Interface Config shutdown This command disables a port. NOTE: You can use the shutdown command on physical and port-channel (LAG) interfaces, but not on VLAN routing interfaces. 2.1.6.1 Default enabled Format shutdown Mode Interface Config no shutdown This command enables a port. 2.1.7 Format no shutdown Mode Interface Config shutdown all This command disables all ports.
AT8904M 2.1.9 Switching Commands speed all This command sets the speed and duplex setting for all interfaces. Format speed all {<100 | 10> } Mode Global Config Acceptable values are: 2.1.10 100h 100BASE-T half-duplex 100f 100BASE-T full duplex 10h 10BASE-T half duplex 10f 10BASE-T full duplex show port This command displays port information.
Switching Commands Mode AT8904M Privileged EXEC Group Name Displays the group name of an entry in the Protocol-based VLAN table. 2.2 Group ID Displays the group identifier of the protocol group. Protocol(s) Indicates the type of protocol(s) for this group. VLAN Indicates the VLAN associated with this Protocol Group. Interface(s) Lists the slot/port interface(s) that are associated with this Protocol Group.
AT8904M 2.2.3 Switching Commands spanning-tree configuration name This command sets the Configuration Identifier Name for use in identifying the configuration that this switch is currently using. The is a string of up to 32 characters. 2.2.3.1 Default base MAC address in hexadecimal notation Format spanning-tree configuration name Mode Global Config no spanning-tree configuration name This command resets the Configuration Identifier Name to its default. 2.2.
Switching Commands 2.2.6 AT8904M spanning-tree forceversion This command sets the Force Protocol Version parameter to a new value. Use 802.1d to specify that the switch transmits ST BPDUs rather than MST BPDUs (IEEE 802.1d functionality supported). Use 802.1w to specify that the switch transmits RST BPDUs rather than MST BPDUs (IEEE 802.1w functionality supported). Use 802.1s to specify that the switch transmits MST BPDUs (IEEE 802.1s functionality supported). 2.2.6.1 Default 802.
AT8904M 2.2.9 Switching Commands Format no spanning-tree hello-time Mode Interface Config spanning-tree max-age This command sets the Bridge Max Age parameter to a new value for the common and internal spanning tree. The max-age value is in seconds within a range of 6 to 40, with the value being less than or equal to 2 x (Bridge Forward Delay - 1). 2.2.9.
Switching Commands AT8904M If you specify the external-cost option, this command sets the external-path cost for MST instance ‘0’ i.e. CIST instance. You can set the external cost as a number in the range of 1 to 200000000 or auto. If you specify auto, the external path cost value is set based on Link Speed.
AT8904M Switching Commands Mode 2.2.12.1 Global Config no spanning-tree mst instance This command removes a multiple spanning tree instance from the switch and reallocates all VLANs allocated to the deleted instance to the common and internal spanning tree. The parameter is a number that corresponds to the desired existing multiple spanning tree instance to be removed. 2.2.
Switching Commands 2.2.14.1 AT8904M no spanning-tree mst vlan This command removes an association between a multiple spanning tree instance and a VLAN so that the VLAN is again be associated with the common and internal spanning tree. The parameter is a number that corresponds to the desired existing multiple spanning tree instance. The corresponds to an existing VLAN ID. 2.2.
AT8904M Switching Commands Bridge Identifier The bridge identifier for the CST. It is made up using the bridge priority and the base MAC address of the bridge. Time Since Topology Change Time in seconds. Topology Change Count Number of times changed. Topology Change Boolean value of the Topology Change parameter for the switch indicating if a topology change is in progress on any port assigned to the common and internal spanning tree. Designated Root The bridge identifier of the root bridge.
Switching Commands 2.2.19 AT8904M show spanning-tree interface This command displays the settings and parameters for a specific switch port within the common and internal spanning tree. The is the desired switch port. The following details are displayed on execution of the command. Format show spanning-tree interface Modes Privileged EXEC User EXEC Hello Time Admin hello time for this port. Port mode Enabled or disabled.
AT8904M Switching Commands Auto-Calculate Port Path Cost This indicates whether auto calculation for port path cost is enabled. Port Path Cost Configured value of the Internal Port Path Cost parameter. Auto-Calculate External Port Path Cost This indicates whether auto calculation for external port path cost is enabled. External Port Path Cost Configured value of the external Port Path Cost parameter. Designated Root The Identifier of the designated root for this port.
Switching Commands 2.2.21 AT8904M show spanning-tree mst port summary This command displays the settings of one or all ports within the specified multiple spanning tree instance. The parameter indicates a particular MST instance. The parameter { | all} indicates the desired switch port or all ports. If you specify 0 (defined as the default CIST ID) as the , the status summary displays for one or all ports within the common and internal spanning tree.
AT8904M Switching Commands Configuration Name Identifier used to identify the configuration currently being used. Configuration Revision Level Identifier used to identify the configuration currently being used. Configuration Digest Key Identifier used to identify the configuration currently being used. MST Instances List of all multiple spanning tree instances configured on the switch 2.2.
Switching Commands 2.3.3 AT8904M vlan This command creates a new VLAN and assigns it an ID. The ID is a valid VLAN identification number (ID 1 is reserved for the default VLAN). VLAN range is 2-4094. 2.3.3.1 Format vlan <2-4094> Mode VLAN Config no vlan This command deletes an existing VLAN. The ID is a valid VLAN identification number (ID 1 is reserved for the default VLAN). The VLAN range is 2-4094. 2.3.
AT8904M 2.3.5.1 Switching Commands no vlan ingressfilter This command disables ingress filtering. If ingress filtering is disabled, frames received with VLAN IDs that do not match the VLAN membership of the receiving interface are admitted and forwarded to ports that are members of that VLAN. 2.3.
Switching Commands auto 2.3.9 AT8904M The interface is dynamically registered in this VLAN by GVRP. The interface will not participate in this VLAN unless a join request is received on this interface. This is equivalent to registration normal. vlan participation all This command configures the degree of participation for all interfaces in a VLAN. The ID is a valid VLAN identification number. You can use the following participation options: • • • 2.3.
AT8904M Switching Commands receiving interface are admitted and forwarded to ports that are members of that VLAN. 2.3.11.1 Default disabled Format vlan port ingressfilter all Mode Global Config no vlan port ingressfilter all This command disables ingress filtering for all ports. If ingress filtering is disabled, frames received with VLAN IDs that do not match the VLAN membership of the receiving interface are admitted and forwarded to ports that are members of that VLAN. 2.3.
Switching Commands 2.3.14 AT8904M vlan protocol group This command adds protocol-based VLAN groups to the system. The is a character string of 1 to 16 characters. When it is created, the protocol group will be assigned a unique number that will be used to identify the group in subsequent commands. 2.3.15 Format vlan protocol group Mode Global Config vlan protocol group add protocol This command adds the to the protocol-based VLAN identified by .
AT8904M 2.3.17.1 Switching Commands no protocol group This command removes the from this protocol-based VLAN group that is identified by this . 2.3.18 Format no protocol group Mode VLAN Config protocol vlan group This command adds the physical interface to the protocol-based VLAN identified by . You can associate multiple interfaces with a group, but you can only associate each interface and protocol combination with one group.
Switching Commands 2.3.20 AT8904M vlan pvid This command changes the VLAN ID per interface. 2.3.20.1 Default 1 Format vlan pvid <1-4094> Mode Interface Config no vlan pvid This command sets the VLAN ID per interface to 1. 2.3.21 Format no vlan pvid Mode Interface Config vlan tagging This command configures the tagging behavior for a specific interface in a VLAN to enabled. If tagging is enabled, traffic is transmitted as tagged frames.
AT8904M Switching Commands Mode 2.3.23.1 VLAN database no vlan association mac This command removes the association of a MAC address to a VLAN. 2.3.24 Format no vlan association mac Mode VLAN database show vlan This command displays detailed information, including interface information, for a specific VLAN. The ID is a valid VLAN identification number. Format show vlan Modes Privileged EXEC User EXEC VLAN ID There is a VLAN Identifier (VID) associated with each VLAN.
Switching Commands AT8904M unless a join request is received on this port. This is equivalent to registration normal in the IEEE 802.1Q standard. Tagging 2.3.25 Select the tagging behavior for this port in this VLAN. Tagged - specifies to transmit traffic for this VLAN as tagged frames. Untagged - specifies to transmit traffic for this VLAN as untagged frames. show vlan brief This command displays a list of all configured VLANs.
AT8904M Switching Commands in the tag. In an untagged frame, the VLAN is the Port VLAN ID specified for the port that received this frame. When disabled, all frames are forwarded in accordance with the 802.1Q VLAN bridge specification. The factory default is disabled. GVRP May be enabled or disabled. Default Priority The 802.1p priority assigned to tagged packets arriving on the port. 2.3.
Switching Commands 2.4.1.1 AT8904M Default vman Format dvlan-tunnel ethertype {802.1Q | vman | custom} [0-65535] Mode Global Config no dvlan-tunnel etherType This command configures the ether-type for all interfaces to the default value. 2.4.2 Format no dvlan-tunnel ethertype Mode Global Config mode dot1q-tunnel This command is used to enable Double VLAN Tunneling on the specified interface. 2.4.2.
AT8904M 2.4.5 Switching Commands Format show dot1q-tunnel [interface { | all}] Modes Privileged EXEC User EXEC Interface Valid slot and port number separated by forward slashes. Mode This field specifies the administrative mode through which Double VLAN Tunneling can be enabled or disabled. The default value for this field is disabled. EtherType This field represents a 2-byte hex EtherType to be used as the first 16 bits of the DVLAN tunnel. There are three different EtherType tags.
Switching Commands Mode 2.5.2 AT8904M Global Config vlan priority This command configures the default 802.1p port priority assigned for untagged packets for a specific interface. The range for the priority is 0-7 2.6 Default 0 Format vlan priority Mode Interface Config Protected Ports Commands This section describes commands you use to configure and view protected ports on a switch. Protected ports do not forward traffic to each other, even if they are on the same VLAN.
AT8904M 2.6.2 Switching Commands switchport protected (Interface Config) Use this command to add an interface to a protected port group. The parameter identifies the set of protected ports to which this interface is assigned. You can only configure an interface as protected in one group. NOTE: Port protection occurs within a single switch. Protected port configuration does not affect traffic between ports on two different switches. No traffic forwarding is possible between two protected ports.
Switching Commands Protected 2.7 AT8904M Indicates whether the interface is protected or not. It shows TRUE or FALSE. If the group is a multiple groups then it shows TRUE in Group GARP Commands This section describes the commands you use to configure Generic Attribute Registration Protocol (GARP) and view GARP status. The commands in this section affect both GARP VLAN Registration Protocol (GVRP) and Garp Multicast Registration Protocol (GMRP).
AT8904M 2.7.2.1 Switching Commands no set garp timer leave This command sets the GVRP leave time on all ports or a single port to the default and only has an effect when GVRP is enabled. 2.7.3 Format no set garp timer leave Modes Interface Config Global Config set garp timer leaveall This command sets how frequently Leave All PDUs are generated. A Leave All PDU indicates that all registrations will be unregistered. Participants would need to rejoin in order to maintain registration.
Switching Commands AT8904M NOTE: If GVRP is disabled, the system does not forward GVRP messages. 2.8.1 set gvrp adminmode This command enables GVRP on the system. 2.8.1.1 Default disabled Format set gvrp adminmode Mode Privileged EXEC no set gvrp adminmode This command disables GVRP. 2.8.2 Format no set gvrp adminmode Mode Privileged EXEC set gvrp interfacemode This command enables GVRP on a single port (Interface Config mode) or all ports (Global Config mode). 2.8.2.
AT8904M Switching Commands 20 centiseconds (0.2 seconds). The finest granularity of specification is one centisecond (0.01 seconds). Leave Timer Specifies the period of time to wait after receiving an unregister request for an attribute before deleting the attribute. Current attributes are a VLAN or multicast group. This may be considered a buffer time for another station to assert registration for the same attribute in order to maintain uninterrupted service.
Switching Commands 2.9.2 AT8904M set gmrp interfacemode This command enables GARP Multicast Registration Protocol on a single interface (Interface Config mode) or all interfaces (Global Config mode). If an interface which has GARP enabled is enabled for routing or is enlisted as a member of a port-channel (LAG), GARP functionality is disabled on that interface.
AT8904M Switching Commands 600 centiseconds (0.2 to 6.0 seconds). The factory default is 60 centiseconds (0.6 seconds). LeaveAll Timer This Leave All Time controls how frequently LeaveAll PDUs are generated. A LeaveAll PDU indicates that all registrations will shortly be deregistered. Participants will need to rejoin in order to maintain registration. There is an instance of this timer on a per-Port, per-GARP participant basis.
Switching Commands AT8904M of authentication login methods is three. The possible method values are local, radius and reject. The value of local indicates that the user’s locally stored ID and password are used for authentication. The value of radius indicates that the user’s ID and password will be authenticated using the RADIUS server. The value of reject indicates the user is never authenticated.
AT8904M Switching Commands assigned to a specific user if the user is configured locally. If this value is not configured, users will be authenticated using local authentication only. 2.10.5 Format dot1x defaultlogin Mode Global Config dot1x initialize This command begins the initialization sequence on the specified port. This command is only valid if the control mode for the specified port is 'auto'. If the control mode is not 'auto' an error will be returned. 2.10.
Switching Commands 2.10.8.1 AT8904M Default auto Format dot1x port-control {force-unauthorized | force-authorized | auto} Mode Interface Config no dot1x port-control This command sets the authentication mode on the specified port to the default value. 2.10.9 Format no dot1x port-control Mode Interface Config dot1x port-control all This command sets the authentication mode to use on all ports.
AT8904M 2.10.11.1 Switching Commands no dot1x re-authentication This command disables re-authentication of the supplicant for the specified port. 2.10.12 Format no dot1x re-authentication Mode Interface Config dot1x system-auth-control Use this command to enable the dot1x authentication support on the switch. While disabled, the dot1x configuration is retained and can be changed, but is not activated. 2.10.12.
Switching Commands 2.10.13.1 AT8904M Format dot1x timeout {{reauth-period } | {quiet-period } | {tx-period } | {supp-timeout } | {server-timeout }} Mode Interface Config no dot1x timeout This command sets the value, in seconds, of the timer used by the authenticator state machine on this port to the default values. Depending on the token used, the corresponding default values are set. 2.10.
AT8904M 2.10.17 Switching Commands Format users login Mode Global Config show authentication This command displays the ordered authentication methods for all authentication login lists. Format show authentication Mode Privileged EXEC Authentication Login List This displays the authentication login listname. 2.10.18 Method 1 This displays the first method in the specified authentication login list, if any.
Switching Commands Port AT8904M The interface whose configuration is displayed. Control Mode The configured control mode for this port. Possible values are forceunauthorized | force-authorized | auto. Operating Control Mode The control mode under which this port is operating. Possible values are authorized | unauthorized. Reauthentication Enabled Indicates whether re-authentication is enabled on this port.
AT8904M Switching Commands The value is expressed in seconds and will be in the range of 1 and 65535. Reauthentication Enabled Indicates if reauthentication is enabled on this port. Possible values are ‘True” or “False”. Key Transmission Enabled Indicates if the key is transmitted to the supplicant for the specified port. Possible values are True or False. Control Direction Indicates the control direction for the specified port or ports. Possible values are both or in.
Switching Commands 2.10.21 AT8904M Format show dot1x users Mode Privileged EXEC User Users configured locally to have access to the specified port. show users authentication This command displays all user and all authentication login information. It also displays the authentication login list assigned to the default user. Format show users authentication Mode Privileged EXEC User Lists every user that has an authentication login list assigned.
AT8904M Switching Commands ingressing on an interface increases beyond the configured threshold, the traffic is dropped. Therefore, the rate of broadcast traffic is limited to the configured threshold. 2.11.2.1 Default 5 Format storm-control broadcast level <0-100> Mode Interface Config no storm-control broadcast level This command sets the broadcast storm recovery threshold to the default value for an interface and disables broadcast storm recovery. 2.11.
Switching Commands 2.11.5 AT8904M Format no storm-control broadcast all level Mode Global Config storm-control multicast This command enables multicast storm recovery mode for an interface. If the mode is enabled, multicast storm recovery is active, and if the rate of L2 multicast traffic ingressing on an interface increases beyond the configured threshold, the traffic will be dropped. Therefore, the rate of multicast traffic will be limited to the configured threshold. 2.11.5.
AT8904M 2.11.7.1 Switching Commands Format storm-control multicast all Mode Global Config no storm-control multicast all This command disables multicast storm recovery mode for all interfaces. 2.11.8 Format no storm-control multicast all Mode Global Config storm-control multicast all level This command configures the multicast storm recovery threshold for all interfaces and enables multicast storm recovery mode.
Switching Commands 2.11.10 AT8904M storm-control unicast level This command configures the unicast storm recovery threshold for an interface and enables unicast storm recovery. If the mode is enabled, unicast storm recovery is active, and if the rate of unknown L2 unicast (destination lookup failure) traffic ingressing on an interface increases beyond the configured threshold, the traffic will be dropped. Therefore, the rate of unknown unicast traffic will be limited to the configured threshold.
AT8904M Switching Commands Mode 2.11.12.1 Global Config no storm-control unicast all level This command returns the unicast storm recovery threshold to the default value and disables unicast storm recovery for all interfaces. 2.11.13 Format no storm-control unicast all level Mode Global Config storm-control flowcontrol This command enables 802.3x flow control for the switch and only applies to fullduplex mode ports. NOTE: 802.
Switching Commands Ucast Level 2.12 AT8904M Shows the Unknown Unicast or DLF (Destination Lookup Failure) storm control level Port-Channel/LAG (802.3ad) Commands This section describes the commands you use to configure port-channels, which are also known as link aggregation groups (LAGs). Link aggregation allows you to combine multiple full-duplex Ethernet links into a single logical link.
AT8904M Switching Commands Mode 2.12.3 Interface Config deleteport (Interface Config) This command deletes the port from the port-channel (LAG). The interface is a Logical slot and port number. of a configured port-channel. 2.12.4 Format deleteport Mode Interface Config deleteport (Global Config) This command deletes all configured ports from the port-channel (LAG). The interface is a Logical slot and port number. of a configured port-channel.
Switching Commands 2.12.7 AT8904M Format no port lacpmode Mode Interface Config port lacpmode all This command enables Link Aggregation Control Protocol (LACP) on all ports. 2.12.7.1 Format port lacpmode all Mode Global Config no port lacpmode all This command disables Link Aggregation Control Protocol (LACP) on all ports. 2.12.8 Format no port lacpmode all Mode Global Config port-channel adminmode This command enables a port-channel (LAG).
AT8904M 2.12.10 Switching Commands port-channel name This command defines a name for the port-channel (LAG). The interface is a logical slot/port for a configured port-channel, and is an alphanumeric string up to 15 characters. 2.12.11 Format port-channel name { | all | } Mode Global Config show port-channel brief This command displays a summary of individual port-channel (LAG) interfaces.
Switching Commands 2.13 AT8904M Mbr Ports A listing of the ports that are members of this port-channel (LAG), in slot/port notation. There can be a maximum of eight ports assigned to a given port-channel (LAG). Port Speed Speed of the port-channel port. Type This field displays the status designating whether a particular portchannel (LAG) is statically or dynamically maintained. Static - The port-channel is statically maintained. Dynamic - The port-channel is dynamically maintained.
AT8904M 2.13.2 Switching Commands no monitor This command removes all the source ports and a destination port for the and restores the default value for mirroring session mode for all the configured sessions. NOTE: This is a stand-alone “no” command. This command does not have a “normal” form. 2.13.3 Default enabled Format no monitor Mode Global Config show monitor session This command displays the Port monitoring information for a particular mirroring session.
Switching Commands 2.14.1.1 AT8904M Format macfilter Mode Global Config no macfilter This command removes all filtering restrictions and the static MAC filter entry for the MAC address on the VLAN . The parameter must be specified as a 6-byte hexadecimal number in the format of b1:b2:b3:b4:b5:b6. The parameter must identify a valid VLAN. 2.14.
AT8904M Switching Commands Mode 2.14.4 Global Config show mac-address-table static This command displays the Static MAC Filtering information for all Static MAC Filters. If you select , all the Static MAC Filters in the system are displayed. If you supply a value for , you must also enter a value for , and the system displays Static MAC Filter information only for that MAC address and VLAN.
Switching Commands AT8904M If an interface has IGMP Snooping enabled and you enable this interface for routing or enlist it as a member of a port-channel (LAG), IGMP Snooping functionality is disabled on that interface. IGMP Snooping functionality is re-enabled if you disable routing or remove port-channel (LAG) membership from an interface that has IGMP Snooping enabled. The IGMP application supports the following activities: • • • 2.15.1.
AT8904M Switching Commands remove the layer 2 LAN interface from its forwarding table entry upon receiving an IGMP leave message for that multicast group without first sending out MAC-based general queries to the interface. You should enable fast-leave admin mode only on VLANs where only one host is connected to each layer 2 LAN port.
Switching Commands AT8904M report for a particular group in that interface. This value must be less than the IGMP Query Interval time value. The range is 1 to 3599 seconds. 2.15.5.1 Default 10 seconds Format set igmp maxresponse <1-3599> Modes Global Config Interface Config VLAN Mode no set igmp maxresponse This command sets the max response time (on the interface or VLAN) to the default value. 2.15.
AT8904M 2.15.8 Switching Commands Format no set igmp mrouter Mode Interface Config set igmp mrouter interface This command configures the interface as a multicast router interface. When configured as a multicast router interface, the interface is treated as a multicast router interface in all VLANs. 2.15.8.
Switching Commands AT8904M Max Response Time Displays the amount of time the switch waits after it sends a query on an interface, participating in the VLAN, because it did not receive a report for a particular group on that interface. This value may be configured. Multicast Router Present Expiration Time Displays the amount of time to wait before removing an interface that is participating in the VLAN from the list of interfaces with multicast routers attached.
AT8904M 2.16 Switching Commands Description The text description of this multicast table entry. Interfaces The list of interfaces that are designated for forwarding (Fwd:) and filtering (Flt:). Port Security Commands This section describes the command you use to configure Port Security on the switch. Port security, which is also known as port MAC locking, allows you to secure the network by locking allowable MAC addresses on a given port.
Switching Commands 2.16.3 AT8904M port-security max-static This command sets the maximum number of statically locked MAC addresses allowed on a specific port. 2.16.3.1 Default 20 Format port-security max-static Mode Interface Config no port-security max-static This command resets the maximum of statically locked MAC addresses allowed on a specific port to its default value. 2.16.
AT8904M Switching Commands Admin Mode Port Locking mode for the Interface. Dynamic Limit Maximum dynamically allocated MAC Addresses. Static Limit Maximum statically allocated MAC Addresses. Violation Trap Mode Whether violation traps are enabled. 2.16.7 show port-security dynamic This command displays the dynamically locked MAC addresses for the port. Format show port-security dynamic Mode Privileged EXEC MAC Address MAC Address of dynamically locked MAC. 2.16.
Switching Commands 2.17.2 AT8904M Format no lldp transmit Mode Interface Config lldp receive Use this command to enable the LLDP receive capability. 2.17.2.1 Default disabled Format lldp receive Mode Interface Configuration no lldp receive Use this command to return the reception of LLDPDUs to the default value. 2.17.3 Format lldp receive Mode Interface Configuration lldp timers Use this command to set the timing parameters for local data transmission on ports enabled for LLDP.
AT8904M 2.17.4.1 Switching Commands Format lldp transmit-tlv [sys-desc] [sys-name] [sys-cap] [portdesc] Mode Interface Config no lldp transmit-tlv Use this command to remove an optional TLV from the LLDPDUs. Use the command without parameters to remove all optional TLVs from the LLDPDU. 2.17.5 Format.
Switching Commands 2.17.7.1 AT8904M Format lldp notification-interval Mode Global Config no lldp notification-interval Use this command to return the notification interval to the default value. 2.17.8 Format no lldp notification-interval Mode Global Config clear lldp statistics Use this command to reset all LLDP statistics. 2.17.9 Format clear lldp statistics Mode Global Config clear lldp remote-data Use this command to delete all information from the LLDP remote data table.
AT8904M 2.17.12 Switching Commands Notify Shows whether the interface sends remote data change notifications. TLVs Shows whether the interface sends optional TLVs in the LLDPDUs. The TLV codes can be 0 (Port Description), 1 (System Name), 2 (System Description), or 3 (System Capability). Mgmt Shows whether the interface transmits system management address information in the LLDPDUs.
Switching Commands AT8904M Chassis ID Shows the ID of the remote device. Port ID Shows the port number that transmitted the LLDPDU. System Name Shows the system name of the remote device. 2.17.14 show lldp remote-device detail Use this command to display detailed information about remote devices that transmit current LLDP data to an interface on the system.
AT8904M 2.17.16 Switching Commands show lldp local-device detail Use this command to display detailed information about the LLDP data a specific interface transmits. Format show lldp local-device detail Mode Privileged EXEC Interface Identifies the interface that sends the LLDPDU. Chassis ID Subtype Shows the type of identification used in the Chassis ID field. Chassis ID Identifies the chassis of the local device. Port ID Subtype Identifies the type of port on the local device.
Switching Commands 2.18.1.1 AT8904M Format dos-control sipdip Mode Global Config no dos-control sipdip This command disables Source IP Address = Destination IP Address (SIP=DIP) Denial of Service prevention. 2.18.2 Format no dos-control sipdip Mode Global Config dos-control firstfrag This command enables Minimum TCP Header Size Denial of Service protection. If the mode is enabled, Denial of Service prevention is active for this type of attack.
AT8904M 2.18.4 Switching Commands dos-control tcpflag This command enables TCP Flag Denial of Service protections. If the mode is enabled, Denial of Service prevention is active for this type of attacks.
Switching Commands Mode 2.18.6.1 AT8904M Global Config no dos-control icmp This command disables Maximum ICMP Packet Size Denial of Service protections. 2.18.7 Format no dos-control icmp Mode Global Config show dos-control This command displays Denial of Service configuration information. Format show dos-control Mod Privileged EXEC SIPDIP Mode May be enabled or disabled. The factory default is disabled. First Fragment Mode May be enabled or disabled. The factory default is disabled.
AT8904M Switching Commands Default all Format show forwardingdb agetime [fdbid | all] Mode Privileged EXEC Forwarding DB ID Fdbid (Forwarding database ID) indicates the forwarding database whose aging timeout is to be shown. The all option is used to display the aging timeouts associated with all forwarding databases. This field displays the forwarding database ID in an IVL system. Agetime 2.19.
Switching Commands AT8904M Most MFDB Entries Ever Used Displays the largest number of entries that have been present in the Multicast Forwarding Database table. This value is also known as the MFDB high-water mark. Current Entries Displays the current number of entries in the MFDB.
AT8904M Chapter 31 Routing Commands Page 3 - 1 AT8904M CLI Reference Manual
Routing Commands 3. AT8904M Routing Commands This chapter describes the routing commands available in the CLI. The Routing Commands chapter contains the following sections: • • • • • • • • 3.1 “Address Resolution Protocol (ARP) Commands” on page 3 - 2 3.2 “IP Routing Commands” on page 3 - 6 3.3 “Router Discovery Protocol Commands” on page 3 - 14 3.4 “Virtual LAN Routing Commands” on page 3 - 16 3.5 “Virtual Router Redundancy Protocol Commands” on page 3 - 17 3.
AT8904M 3.1.2 Routing Commands ip proxy-arp This command enables proxy ARP on a router interface. Without proxy ARP, a device only responds to an ARP request if the target IP address is an address configured on the interface where the ARP request arrived. With proxy ARP, the device may also respond if the target IP address is reachable. The device only responds if all next hops in its route to the destination are through interfaces other than the interface that received the ARP request. 3.1.2.
Routing Commands 3.1.5 AT8904M arp purge This command causes the specified IP address to be removed from the ARP cache. Only entries of type dynamic or gateway are affected by this command. 3.1.6 Format arp purge Mode Privileged EXEC arp resptime This command configures the ARP request response timeout. The value for is a valid positive integer, which represents the IP ARP entry response timeout time in seconds. The range for is between 1-10 seconds. 3.1.6.
AT8904M 3.1.8.1 Routing Commands no arp timeout This command configures the default ARP entry ageout time. 3.1.9 Format no arp timeout Mode Global Config clear arp-cache This command causes all ARP entries of type dynamic to be removed from the ARP cache. If the gateway keyword is specified, the dynamic entries of type gateway are purged as well. 3.1.10 Format clear arp-cache Mode Privileged EXEC [gateway] show arp This command displays the Address Resolution Protocol (ARP) cache.
Routing Commands 3.1.11 AT8904M show arp brief This command displays the brief Address Resolution Protocol (ARP) table information. Format show arp brief Mode Privileged EXEC Age Time (seconds) The time it takes for an ARP entry to age out. This value is configurable. Age time is measured in seconds. Response Time (seconds) The time it takes for an ARP request timeout. This value is configurable. Response time is measured in seconds. Retries The maximum number of times an ARP request is retried.
AT8904M 3.2.1.1 Routing Commands no routing This command disables routing for an interface. You can view the current value for this function with the show ip brief command. The value is labeled as “Routing Mode.” 3.2.2 Format no routing Mode Interface Config ip routing This command enables the IP Router Admin Mode for the master switch. 3.2.2.1 Format ip routing Mode Global Config no ip routing This command disables the IP Router Admin Mode for the master switch. 3.2.
Routing Commands AT8904M routing protocols. The preference also controls whether a static route is more or less preferred than other static routes to the same destination. A route with a preference of 255 cannot be used to forward traffic. For the static routes to be visible, you must perform the following steps: • • • 3.2.4.1 Enable ip routing globally. Enable ip routing for the interface. Confirm that the associated link is also up.
AT8904M 3.2.6.1 Routing Commands Default 1 Format ip route distance Mode Global Config <1-255> no ip route distance This command sets the default static route preference value in the router. Lower route preference values are preferred when determining the best route. 3.2.7 Format no ip route distance Mode Global Config ip forwarding This command enables forwarding of IP frames. 3.2.7.
Routing Commands AT8904M Packets originated on the router, such as OSPF packets, may be fragmented by the IP stack. The IP stack uses its default IP MTU and ignores the value set using the ip mtu command. OSPF advertises the IP MTU in the Database Description packets it sends to its neighbors during database exchange. If two OSPF neighbors advertise different IP MTUs, they will not form an adjacency. (unless OSPF has been instructed to ignore differences in IP MTU with the ip ospf mtu-ignore command.
AT8904M 3.2.12 Routing Commands show ip interface This command displays all pertinent information about the IP interface. Format show ip interface Modes Privileged EXEC User EXEC Primary IP Address The primary IP address and subnet masks for the interface. This value appears only if you configure it. Secondary IP Address One or more secondary IP addresses and subnet masks for the interface. This value appears only if you configure it.
Routing Commands AT8904M IP Mask The IP mask of the routing interface in 32-bit dotted decimal format. Netdir Bcast Indicates if IP forwards net-directed broadcasts on this interface. Possible values are Enable or Disable. MultiCast Fwd The multicast forwarding administrative mode on the interface. Possible values are Enable or Disable. 3.2.14 show ip route This command displays the routing table.
AT8904M Routing Commands Format show ip route summary Mode Privileged EXEC User EXEC [all] Connected Routes The total number of connected routes in the routing table. Static Routes Total number of static routes in the routing table. RIP Routes Total number of routes installed by RIP protocol. OSPF Routes Total number of routes installed by OSPF protocol. Total Routes 3.2.16 Total number of routes in the routing table.
Routing Commands 3.3 AT8904M Router Discovery Protocol Commands This section describes the commands you use to view and configure Router Discovery Protocol settings on the switch. The Router Discovery Protocol enables a host to discover the IP address of routers on the subnet. 3.3.1 ip irdp This command enables Router Discovery on an interface. 3.3.1.1 Default disabled Format ip irdp Mode Interface Config no ip irdp This command disables Router Discovery on an interface. 3.3.
AT8904M 3.3.3.1 Routing Commands no ip irdp holdtime This command configures the default value, in seconds, of the holdtime field of the router advertisement sent from this interface. 3.3.4 Format no ip irdp holdtime Mode Interface Config ip irdp maxadvertinterval This command configures the maximum time, in seconds, allowed between sending router advertisements from the interface. The range for maxadvertinterval is 4 to 1800 seconds. 3.3.4.
Routing Commands 3.3.6.1 AT8904M no ip irdp preference This command configures the default preferability of the address as a default router address, relative to other router addresses on the same subnet. 3.3.7 Format no ip irdp preference Mode Interface Config show ip irdp This command displays the router discovery information for all interfaces, or a specified interface.
AT8904M Routing Commands Mode 3.4.2 VLAN Config show ip vlan This command displays the VLAN routing information for all VLANs with routing enabled. Format show ip vlan Modes Privileged EXEC User EXEC MAC Address used by Routing VLANs The MAC Address associated with the internal bridge-router interface (IBRI). The same MAC Address is used by all VLAN routing interfaces. It will be displayed above the per-VLAN information. VLAN ID The identifier of the VLAN.
Routing Commands 3.5.2.1 AT8904M no ip vrrp Use this command in Interface Config mode to delete the virtual router associated with the interface. The virtual Router ID, , is an integer value that ranges from 1 to 255. 3.5.3 Format no ip vrrp Mode Interface Config ip vrrp mode This command enables the virtual router configured on the specified interface. Enabling the status field starts a virtual router.
AT8904M Routing Commands optional, it is only required when authorization type is simple text password. The parameter is the virtual router ID which has an integer value ranges from 1 to 255. 3.5.5.1 Default no authorization Format ip vrrp Mode Interface Config authentication {none | simple } no ip vrrp authentication This command sets the default authorization details value for the virtual router configured on a specified interface. 3.5.
Routing Commands 3.5.7.1 AT8904M no ip vrrp priority This command sets the default priority value for the virtual router configured on a specified interface. 3.5.8 Format no ip vrrp Mode Interface Config priority ip vrrp timers advertise This command sets the frequency, in seconds, that an interface on the specified virtual router sends a virtual router advertisement. 3.5.8.
AT8904M Routing Commands Zero Priority Packets Sent The total number of VRRP packets sent by the virtual router with a priority of '0'. Invalid Type Packets Received The total number of VRRP packets received by the virtual router with invalid 'type' field. Address List Errors The total number of VRRP packets received for which address list does not match the locally configured list for the virtual router.
Routing Commands AT8904M Administrative Mode The status (Enable or Disable) of the specific router. State 3.5.12 The state (Master/backup) of the virtual router. show ip vrrp interface brief This command displays information about each virtual router configured on the FASTPATH switch. This command takes no options. It displays information about each virtual router. 3.
AT8904M 3.6.2.1 Routing Commands no bootpdhcprelay enable This command disables the forwarding of relay requests for BootP/DHCP Relay on the system. 3.6.3 Format no bootpdhcprelay enable Mode Global Config bootpdhcprelay maxhopcount This command configures the maximum allowable relay agent hops for BootP/DHCP Relay on the system. The parameter has a range of 1 to 16. 3.6.3.
Routing Commands 3.6.5.1 AT8904M no bootpdhcprelay serverip This command configures the default server IP address for BootP/DHCP Relay on the system. 3.6.6 Format no bootpdhcprelay serverip Mode Global Config show bootpdhcprelay This command displays the BootP/DHCP Relay information. Format show bootpdhcprelay Modes Privileged EXEC User EXEC Maximum Hop Count The maximum allowable relay agent hops. Minimum Wait Time (Seconds) The minimum wait time.
AT8904M Routing Commands Mode 3.7.3 Router OSPF Config ip ospf This command enables OSPF on a router interface. 3.7.3.1 Default disabled Format ip ospf Mode Interface Config no ip ospf This command disables OSPF on a router interface. 3.7.4 Format no ip ospf Mode Interface Config 1583compatibility This command enables OSPF 1583 compatibility. NOTE: 1583 compatibility mode is enabled by default.
Routing Commands 3.7.7 AT8904M Format no area nssa Mode Router OSPF Config area nssa default-info-originate (OSPF) This command configures the metric value and type for the default route advertised into the NSSA. The optional metric parameter specifies the metric of the default route and is to be in a range of 1-16777214. If no metric is specified, the default value is ****. The metric type can be comparable (nssa-external 1) or non-comparable (nssaexternal 2). 3.7.7.
AT8904M 3.7.10 Routing Commands area nssa translator-role (OSPF) This command configures the translator role of the NSSA. A value of always causes the router to assume the role of the translator the instant it becomes a border router and a value of candidate causes the router to participate in the translator election process when it attains border router status. 3.7.10.
Routing Commands 3.7.13 AT8904M area stub (OSPF) This command creates a stub area for the specified area ID. A stub area is characterized by the fact that AS External LSAs are not propagated into the area. Removing AS External LSAs and Summary LSAs can significantly reduce the link state database of routers within the stub area. 3.7.13.1 Format area Mode Router OSPF Config stub no area stub This command deletes a stub area for the specified area ID. 3.7.
AT8904M 3.7.16 Routing Commands area virtual-link authentication This command configures the authentication type and key for the OSPF virtual interface identified by and . The parameter is the Router ID of the neighbor. The value for is either none, simple, or encrypt. The [key] is composed of standard displayable, non-control keystrokes from a Standard 101/102-key keyboard. The authentication key must be 8 bytes or less if the authentication type is simple.
Routing Commands 3.7.18.1 AT8904M Format area virtual-link hello-interval <165535> Mode Router OSPF Config no area virtual-link hello-interval This command configures the default hello interval for the OSPF virtual interface on the virtual interface identified by and . The parameter is the Router ID of the neighbor. 3.7.
AT8904M 3.7.21 Routing Commands default-information originate (OSPF) This command is used to control the advertisement of default routes. Default metric—unspecified type—2 Format default-information originate [always] [metric <0-16777214>] [metric-type {1 | 2}] Mode 3.7.21.1 Router OSPF Config no default-information originate (OSPF) This command is used to control the advertisement of default routes. 3.7.
Routing Commands Mode 3.7.24 AT8904M Router OSPF Config distribute-list out (OSPF) Use this command to specify the access list to filter routes received from the source protocol. 3.7.24.1 Format distribute-list Mode Router OSPF Config <1-199> out {rip | static | connected} no distribute-list out Use this command to specify the access list to filter routes received from the source protocol. 3.7.
AT8904M 3.7.26.1 Routing Commands no external-lsdb-limit This command configures the default external LSDB limit for OSPF. 3.7.27 Format no external-lsdb-limit Mode Router OSPF Config ip ospf areaid This command sets the OSPF area to which the specified router interface belongs. The is an IP address, formatted as a 4-digit dotted-decimal number or a decimal value in the range of <0-4294967295>. The uniquely identifies the area to which the interface connects.
Routing Commands Mode 3.7.30 AT8904M Interface Config ip ospf dead-interval This command sets the OSPF dead interval for the specified interface. The value for is a valid positive integer, which represents the length of time in seconds that a router's Hello packets have not been seen before its neighbor routers declare that the router is down. The value for the length of time must be the same for all routers attached to a common network.
AT8904M 3.7.32.1 Routing Commands no ip ospf priority This command sets the default OSPF priority for the specified router interface. 3.7.33 Format no ip ospf priority Mode Interface Config ip ospf retransmit-interval This command sets the OSPF retransmit Interval for the specified interface. The retransmit interval is specified in seconds. The value for is the number of seconds between link-state advertisement retransmissions for adjacencies belonging to this router interface.
Routing Commands 3.7.35.1 AT8904M Default enabled Format ip ospf mtu-ignore Mode Interface Config no ip ospf mtu-ignore This command enables the OSPF MTU mismatch detection. 3.7.36 Format no ip ospf mtu-ignore Mode Interface Config router-id (OSPF) This command sets a 4-digit dotted-decimal number uniquely identifying the router ospf id. The is a configured value. 3.7.
AT8904M 3.7.38.1 Routing Commands no maximum-paths This command resets the number of paths that OSPF can report for a given destination back to its default value. 3.7.39 Format no maximum-paths Mode Router OSPF Config timers spf Use this command to configure the SPF delay time and hold time. The valid range for both parameters is 0-65535 seconds. 3.7.
Routing Commands AT8904M learnt by other protocols) or disabled (if the router is not configured for the same). RFC 1583 Compatibility Indicates whether 1583 compatibility is enabled or disabled. This is a configured value. ABR Status Shows whether the router is an OSPF Area Border Router. Exit Overflow Interval The number of seconds that, after entering OverflowState, a router will attempt to leave OverflowState.
AT8904M Routing Commands Format show ip ospf abr Modes Privileged EXEC User EXEC Type The type of the route to the destination. It can be either: intra — Intra-area route inter — Inter-area route Router ID Router ID of the destination Cost Cost of using this route Area ID The area ID of the area from which this route is learned. Next Hop Next hop toward the destination Next Hop Intf The outgoing router interface to use when forwarding traffic to the next hop. 3.7.
Routing Commands AT8904M Default Metric The metric value for the default route advertised into the NSSA. Default Metric Type The metric type for the default route advertised into the NSSA. Translator Role The NSSA translator role of the ABR, which is always or candidate. Translator Stability Interval The amount of time that an elected translator continues to perform its duties after it determines that its translator status has been deposed by another router.
AT8904M 3.7.45 Routing Commands show ip ospf database database-summary Use this command to display the number of each type of LSA in the database for each area and for the router. The command also displays the total number of LSAs in the database. Format show ip ospf database database-summary Modes Privileged EXEC User EXEC Router Total number of router LSAs in the OSPF link state database. Network Total number of network LSAs in the OSPF link state database.
Routing Commands AT8904M Transit Delay Interval A number representing the OSPF Transit Delay for the specified interface. Authentication Type The OSPF Authentication Type for the specified interface are: none, simple, and encrypt. The information below will only be displayed if OSPF is enabled. OSPF Interface Type Broadcast LANs, such as Ethernet and IEEE 802.5, take the value broadcast. The OSPF Interface Type will be 'broadcast'.
AT8904M Routing Commands Modes Privileged EXEC User EXEC OSPF Area ID The area id of this OSPF interface. Area Border Router Count The total number of area border routers reachable within this area. This is initially zero, and is calculated in each SPF pass. AS Border Router Count The total number of Autonomous System border routers reachable within this area. Area LSA Count The total number of link-state advertisements in this area's linkstate database, excluding AS External LSAs.
Routing Commands AT8904M Authentication Failure The number of OSPF packets dropped because the sender is not an existing neighbor or the sender’s IP address does not match the previously recorded IP address for that neighbor. (NOTE: This field only applies to OSPFv2.) No Neighbor at Source Address The number of OSPF packets dropped because the sender is not an existing neighbor or the sender’s IP address does not match the previously recorded IP address for that neighbor. NOTE: Does not apply to Hellos.
AT8904M Routing Commands Attempt - no recent information has been received from the neighbor but a more concerted effort should be made to contact the neighbor. Init - an Hello packet has recently been seen from the neighbor, but bidirectional communication has not yet been established. 2 way - communication between the two routers is bidirectional.
Routing Commands 3.7.50 AT8904M show ip ospf range This command displays information about the area ranges for the specified . The identifies the OSPF area whose ranges are being displayed. Format show ip ospf range Modes Privileged EXEC User EXEC Area ID The area id of the requested OSPF area. IP Address An IP address which represents this area range. Subnet Mask A valid subnet mask for this area range.
AT8904M Routing Commands Metric Val The metric value is applied based on the TOS. It defaults to the least metric of the type of service among the interfaces to other areas. The OSPF cost for a route is a function of the metric value. Import Summary LSA Controls the import of summary LSAs into stub areas. 3.7.53 show ip ospf virtual-link This command displays the OSPF Virtual Interface information for a specific area and neighbor.
Routing Commands 3.8 AT8904M Routing Information Protocol (RIP) Commands This section describes the commands you use to view and configure RIP, which is a distance-vector routing protocol that you use to route traffic within a small network. 3.8.1 router rip Use this command to enter Router RIP mode. 3.8.2 Format router rip Mode Global Config enable (RIP) This command resets the default administrative mode of RIP in the router (active). 3.8.2.
AT8904M 3.8.5 Routing Commands Format no auto-summary Mode Router RIP Config default-information originate (RIP) This command is used to control the advertisement of default routes. 3.8.5.1 Format default-information originate Mode Router RIP Config no default-information originate (RIP) This command is used to control the advertisement of default routes. 3.8.
Routing Commands 3.8.8.1 AT8904M Default 0 Format distribute-list Mode Router RIP Config <1-199> out {ospf | static | connected} no distribute-list out This command is used to specify the access list to filter routes received from the source protocol. 3.8.9 Format no distribute-list Mode Router RIP Config <1-199> out {ospf | static | connected} ip rip authentication This command sets the RIP Version 2 Authentication Type and Key for the specified interface.
AT8904M 3.8.11 Routing Commands ip rip send version This command configures the interface to allow RIP control packets of the specified version to be sent. The value for is one of: rip1 to broadcast RIP version 1 formatted packets, rip1c (RIP version 1 compatibility mode) which sends RIP version 2 formatted packets via broadcast, rip2 for sending RIP version 2 using multicast, or none to not allow any RIP control packets to be sent. 3.8.11.
Routing Commands Mode 3.8.14 AT8904M Router RIP Config redistribute (RIP) This command configures RIP protocol to redistribute routes from the specified source protocol/routers. There are five possible match options. When you submit the command redistribute ospf match the match-type or types specified are added to any match types presently being redistributed. Internal routes are redistributed by default.
AT8904M 3.8.16 Routing Commands show ip rip interface brief This command displays general information for each RIP interface. For this command to display successful results routing must be enabled per interface (i.e. ip rip). Format show ip rip interface brief Modes Privileged EXEC User EXEC Interface Valid slot and port number separated by forward slashes. IP Address The IP source address used by the specified RIP interface.
Routing Commands AT8904M Bad Packets Received The number of RIP response packets received by the RIP process which were subsequently discarded for any reason. Bad Routes Received The number of routes contained in valid RIP packets that were ignored for any reason. Updates Sent The number of triggered RIP updates actually sent on this interface.
AT8904M Chapter 41 Quality of Service Commands Page 4 - 1 AT8904M CLI Reference Manual
Quality of Service (QoS) Commands 4. AT8904M Quality of Service (QoS) Commands This chapter describes the Quality of Service (QoS) commands available in the CLI. The QoS Commands chapter contains the following sections: • • • • • • • • • 4.1 “Class of Service (CoS) Commands” on page 4 - 2 4.2 “Differentiated Services (DiffServ) Commands” on page 4 - 6 4.3 “DiffServ Class Commands” on page 4 - 8 4.4 “DiffServ Policy Commands” on page 4 - 14 4.5 “DiffServ Service Commands” on page 4 - 18 4.
AT8904M Quality of Service (QoS) Commands Modes 4.1.2 Global Config Interface Config classofservice ip-dscp-mapping This command maps an IP DSCP value to an internal traffic class. The value is specified as either an integer from 0 to 63, or symbolically through one of the following keywords: af11, af12, af13, af21, af22, af23, af31, af32, af33, af41, af42, af43, be, cs0, cs1, cs2, cs3, cs4, cs5, cs6, cs7, ef.
Quality of Service (QoS) Commands 4.1.4 AT8904M cos-queue min-bandwidth This command specifies the minimum transmission bandwidth guarantee for each interface queue. The total number of queues supported per interface is platform specific. A value from 0-100 (percentage of link rate) must be specified for each supported queue, with 0 indicating no guaranteed minimum bandwidth. The sum of all values entered must not exceed 100. 4.1.4.
AT8904M Quality of Service (QoS) Commands Modes 4.1.7 Global Config Interface Config show classofservice dot1p-mapping This command displays the current Dot1p (802.1p) priority mapping to internal traffic classes for a specific interface. The parameter is optional and is only valid on platforms that support independent per-port class of service mappings. If specified, the 802.1p mapping table of the interface is displayed.
Quality of Service (QoS) Commands 4.1.10 AT8904M show classofservice trust This command displays the current trust mode setting for a specific interface. The parameter is optional and is only valid on platforms that support independent per-port class of service mappings. If you specify an interface, the command displays the port trust mode of the interface. If you do not specify an interface, the command displays the most recent global configuration settings.
AT8904M Quality of Service (QoS) Commands You configure DiffServ in several stages by specifying three DiffServ components: 1. Class - Creating and deleting classes. - Defining match criteria for a class. 2. Policy - Creating and deleting policies - Associating classes with a policy - Defining policy statements for a policy/class combination 3. Service - Adding and removing a policy to/from an inbound interface The DiffServ class defines the packet filtering criteria.
Quality of Service (QoS) Commands 4.2.1.1 AT8904M no diffserv This command sets the DiffServ operational mode to inactive. While disabled, the DiffServ configuration is retained and can be changed, but it is not activated. When enabled, Diffserv services are activated. 4.3 Format no diffserv Mode Global Config DiffServ Class Commands Use the DiffServ class commands to define traffic classification.
AT8904M 4.3.2 Quality of Service (QoS) Commands class-map rename This command changes the name of a DiffServ class. The is the name of an existing DiffServ class. The parameter is a casesensitive alphanumeric string from 1 to 31 characters uniquely identifying the class (The ‘default’ is reserved and must not be used here). 4.3.
Quality of Service (QoS) Commands • 4.3.5.1 AT8904M The total number of class rules formed by the complete reference class chain (including both predecessor and successor classes) must not exceed a platformspecific maximum. In some cases, each removal of a refclass rule reduces the maximum number of available rules in the class definition by one. no match class-map This command removes from the specified class definition the set of match conditions defined for another class.
AT8904M 4.3.9 Quality of Service (QoS) Commands match dstip This command adds to the specified class definition a match condition based on the destination IP address of a packet. The parameter specifies an IP address and specifies a subnet mask and must consist of a contiguous set of leading 1 bits. 4.3.
Quality of Service (QoS) Commands AT8904M NOTE: The IP DSCP, IP Precedence, and IP ToS match conditions are alternative ways to specify a match criterion for the same Service Type field in the IP header, but with a slightly different user notation. 4.3.
AT8904M 4.3.15 Quality of Service (QoS) Commands match source-address mac This command adds to the specified class definition a match condition based on the source MAC address of a packet. The
parameter is any layer 2 MAC address formatted as six, two-digit hexadecimal numbers separated by colons (e.g., 00:11:22:dd:ee:ff). The parameter is a layer 2 MAC address bit mask, which may not be contiguous, and is formatted as six, two-digit hexadecimal numbers separated by colons (e.g.Quality of Service (QoS) Commands Mode 4.3.19 AT8904M Class-Map Config match secondary-vlan This command adds to the specified class definition a match condition based on the value of the layer 2 secondary VLAN Identifier field (the inner 802.1Q tag of a double VLAN tagged packet). The secondary VLAN ID is an integer from 1 to 4095. NOTE: This command is not available on the Broadcom 5630x platform. 4.
AT8904M 4.4.2 Quality of Service (QoS) Commands drop This command specifies that all packets for the associated traffic stream are to be dropped at ingress. Format drop Mode Policy-Class-Map Config Incompatibilities Assign Queue, Mark (all forms), Mirror, Police, Redirect 4.4.3 mirror This command specifies that all incoming packets for the associated traffic stream are copied to a specific egress interface (physical port or LAG). NOTE: This command is not available on the Broadcom 5630x platform.
Quality of Service (QoS) Commands AT8904M NOTE: The CLI mode is changed to Policy-Class-Map Config when this command is successfully executed. 4.4.6.1 Format class Mode Policy-Map Config no class This command deletes the instance of a particular class and its defined treatment from the specified policy. is the names of an existing DiffServ class. NOTE: This command removes the reference to the class definition for the specified policy. 4.4.
AT8904M Quality of Service (QoS) Commands Incompatibilities Drop, Mark CoS, Mark IP DSCP, Police 4.4.10 police-simple This command is used to establish the traffic policing style for the specified class. The simple form of the police command uses a single data rate and burst size, resulting in two outcomes: conform and violate. The conforming data rate is specified in kilobitsper-second (Kbps) and is an integer from 1 to 4294967295.
Quality of Service (QoS) Commands 4.4.12 AT8904M policy-map rename This command changes the name of a DiffServ policy. The is the name of an existing DiffServ class. The parameter is a case-sensitive alphanumeric string from 1 to 31 characters uniquely identifying the policy. 4.
AT8904M Quality of Service (QoS) Commands inbound direction. There is no separate interface administrative 'mode' command for DiffServ. 4.6 Format no service-policy in Modes Global Config Interface Config DiffServ Show Commands Use the DiffServ show commands to display configuration and status information for classes, policies, and services. You can display DiffServ information in summary or detailed formats.
Quality of Service (QoS) Commands 4.6.2 AT8904M show diffserv This command displays the DiffServ General Status Group information, which includes the current administrative mode setting as well as the current and maximum number of rows in each of the main DiffServ private MIB tables. This command takes no options. Format show diffserv Mode Privileged EXEC DiffServ Admin mode The current value of the DiffServ administrative mode.
AT8904M Quality of Service (QoS) Commands Assign Queue Directs traffic stream to the specified QoS queue. This allows a traffic classifier to specify which one of the supported hardware queues are used for handling packets belonging to the class. Class Name The name of this class. Committed Burst Size (KB) The committed burst size, used in simple policing.
Quality of Service (QoS) Commands AT8904M If the Policy Name is not specified this command displays a list of all defined DiffServ policies. The following fields are displayed: Policy Name The name of this policy. (The order in which the policies are displayed is not necessarily the same order in which they were created.) Policy Type The policy type (Only inbound is supported). Class Members List of all class names associated with this policy. 4.6.
AT8904M 4.6.6 Quality of Service (QoS) Commands show policy-map interface This command displays policy-oriented statistics information for the specified interface and direction. The parameter specifies a valid interface for the system. NOTE: This command is only allowed while the DiffServ administrative mode is enabled. Format show policy-map interface [in] Mode Privileged EXEC Interface Valid slot and port number separated by forward slashes.
Quality of Service (QoS) Commands 4.7.1 AT8904M mac access-list extended This command creates a MAC Access Control List (ACL) identified by , consisting of classification fields defined for the Layer 2 header of an Ethernet frame. The parameter is a case-sensitive alphanumeric string from 1 to 31 characters uniquely identifying the MAC access list. If a MAC ACL by this name already exists, this command enters Mac-Access-List config mode to allow updating the existing MAC ACL.
AT8904M Quality of Service (QoS) Commands The Ethertype may be specified as either a keyword or a four-digit hexadecimal value from 0x0600-0xFFFF. The currently supported values are: appletalk, arp, ibmsna, ipv4, ipv6, ipx, mplsmcast, mplsucast, netbios, novell, pppoe, rarp. Each of these translates into its equivalent Ethertype value(s). Table 1.
Quality of Service (QoS) Commands 4.7.4 AT8904M mac access-group This command attaches a specific MAC Access Control List (ACL) identified by to an interface in a given direction. The parameter must be the name of an existing MAC ACL. An optional sequence number may be specified to indicate the order of this mac access list relative to other mac access lists already assigned to this interface and direction. A lower number indicates higher precedence order.
AT8904M Quality of Service (QoS) Commands Mirror Interface On Broadcom 5650x platforms, the slot/port to which packets matching this rule are copied. Redirect Interface On Broadcom 5650x platforms, the slot/port to which packets matching this rule are forwarded. 4.8 IP Access Control List (ACL) Commands This section describes the commands you use to configure IP ACL settings.
Quality of Service (QoS) Commands AT8904M Table 2. ACL Command Parameters Parameter Description <1-99> or <100-199> Range 1 to 99 is the access list number for an IP standard ACL. Range 100 to 199 is the access list number for an IP extended ACL. {deny | permit} Specifies whether the IP ACL rule permits or denies an action. Note: For 5630x and 5650x-based systems, assign-queue, redirect, and mirror attributes are configurable for a deny rule, but they have no operational effect.
AT8904M 4.8.2 Quality of Service (QoS) Commands ip access-group This command attaches a specified IP ACL to one interface or to all interfaces. An optional sequence number may be specified to indicate the order of this IP access list relative to other IP access lists already assigned to this interface and direction. A lower number indicates higher precedence order.
Quality of Service (QoS) Commands AT8904M Action The action associated with each rule. The possible values are Permit or Deny. Match All Indicates whether this access list applies to every packet. Possible values are True or False. Protocol The protocol to filter for this rule. Source IP Address The source IP address for this rule. Source IP Mask The source IP Mask for this rule. Source L4 Port Keyword The source port for this rule. Destination IP Address The destination IP address for this rule.
AT8904M Quality of Service (QoS) Commands 4.9 ACL trap commands 4.9.1 acl-traptimer This command sets the time interval for generating ACL traps. An ACL trap is generated if ACL trap generation is enabled and an ACL rule applies for an incoming packet. The generation is checked for a specified time interval. The time interval value indicates seconds. The range is 30..600, the default value is 300. 4.9.
Quality of Service (QoS) Commands AT8904M CLI Reference Manual Page 4 - 32 AT8904M
AT8904M Chapter 51 Utility Commands Page 5 - 1 AT8904M CLI Reference Manual
Utility Commands 5. AT8904M Utility Commands This chapter describes the utility commands available in the CLI. The FASTPATH Utility Commands chapter includes the following sections: • • • • • • • • • • • 5.1 “Commands for update and startup Configuration” on page 5 - 2 5.2 “ATCA commands” on page 5 - 4 5.3 “System Information and Statistics Commands” on page 5 - 6 5.4 “Logging Commands” on page 5 - 20 5.5 “System Utility and Clear Commands” on page 5 - 24 5.
AT8904M 5.1.3 Utility Commands download frudata This command updates the IPMI FRU data. It downloades a FRU image from and updates the PM with the new FRU data. If the flash process is interrupted or fails, FRU data may be corrupted and the download process has to be retried until it finishes successfully. 5.1.4 Format download frudata Mode Privileged EXEC download fwum This command updates the FWUM firmware.
Utility Commands 5.1.8 AT8904M startupslot activate This command sets the startup slot to active and will use this in all subsequent reboots. Using [once] at the end of the command will set the startup slot to be used once during the next restart. The start sequence will reset the startup slot to the previously installed one. This enables a try-once with automatic rollback in case of error. 5.1.
AT8904M 5.2.3 Utility Commands set board fcap This command enables or disables some firmware capabilities. If the handle capability is enabled, the hardware handle is ignored. 5.2.4 Format set board fcap handle enable set board fcap handle disable Mode Privileged EXEC show boardinfo fcap This command shows the user changeable firmware capabilities. 5.2.
Utility Commands 5.2.8 AT8904M show atca ekeying This command displays the current ekeying status together with admin mode and link status for all interfaces. For uplink interfaces no ekeying state is displayed. 5.3 Format show atca ekeying all Mode Privileged EXEC System Information and Statistics Commands This section describes the commands you use to view information about system features, components, and configurations. 5.3.
AT8904M Utility Commands hardware command will not be available. For a description of the command output, see 5.3.4 “show version” on page 5 - 7. 5.3.4 Format show hardware Mode Privileged EXEC show version This command displays inventory information for the switch. NOTE: The show version command will replace the show hardware command in future releases of the software. Format show version Mode Privileged EXEC Switch Description Text used to identify the product name of this switch.
Utility Commands AT8904M Broadcast Packets Received The total number of packets received that were directed to the broadcast address. Note that this does not include multicast packets. Packets Transmitted Without Error The total number of packets transmitted out of the interface. Transmit Packets Errors The number of outbound packets that could not be transmitted because of errors. Collisions Frames The best estimate of the total number of collisions on this Ethernet segment.
AT8904M Utility Commands on the network (excluding framing bits but including Frame Check Sequence (FCS) octets). This object can be used as a reasonable estimate of Ethernet utilization. If greater precision is desired, the etherStatsPkts and etherStatsOctets objects should be sampled before and after a common interval. The result of this equation is the value Utilization which is the percent utilization of the Ethernet segment on a scale of 0 to 100 percent.
Utility Commands AT8904M that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets). Packets RX and TX 1519-1522 Octets - The total number of packets (including bad packets) received and transmitted that were between 1519 and 1522 octets in length inclusive (excluding framing bits but including FCS octets).
AT8904M Utility Commands Rx FCS Errors - The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but had a bad Frame Check Sequence (FCS) with an integral number of octets Overruns - The total number of frames discarded as this port was overloaded with incoming packets, and could not keep up with the inflow.
Utility Commands AT8904M Packets Transmitted 256-511 Octets - The total number of packets (including bad packets) received that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets). Packets Transmitted 512-1023 Octets - The total number of packets (including bad packets) received that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).
AT8904M Utility Commands Excessive Collisions - A count of frames for which transmission on a particular interface fails due to excessive collisions. Port Membership Discards - The number of frames discarded on egress for this port due to egress filtering being enabled. Protocol Statistics 802.3x Pause Frames Transmitted - A count of MAC Control frames transmitted on this interface with an opcode indicating the PAUSE operation.
Utility Commands AT8904M Multicast Packets Received The total number of packets received that were directed to a multicast address. Note that this number does not include packets directed to the broadcast address. Broadcast Packets Received The total number of packets received that were directed to the broadcast address. Note that this does not include multicast packets.
AT8904M 5.3.7 Utility Commands show mac-addr-table This command displays the forwarding database entries. These entries are used by the transparent bridging function to determine how to forward a received frame. Enter all or no parameter to display the entire table. Enter a MAC Address and VLAN ID to display the table entry for the requested MAC address on the specified VLAN. Enter the count parameter to view summary information about the forwarding database table.
Utility Commands AT8904M Static Address (User-defined) count Number of MAC addresses in the forwarding database that were manually entered by a user. Total MAC Addresses in use Number of MAC addresses currently in the forwarding database. Total MAC Addresses available Number of MAC addresses the forwarding database can handle. 5.3.8 show running-config Use this command to display or capture the current setting of different protocol packages supported on the switch.
AT8904M 5.3.10 Utility Commands show tech-support Use the show tech-support command to display system and configuration information when you contact technical support. The output of the show techsupport command combines the output of the following commands: • • • • • • • • 5.3.
Utility Commands 5.3.15 AT8904M Format show boardinfo update-status Mode Privileged EXEC show boardinfo version This command displays hardware and software revision information. This includes serial-numbers, software and hardware revisions as applicable. Format show boardinfo version Mode Privileged EXEC Version information included • • • • • • • • • • • • • • • • • 5.3.
AT8904M 5.3.19 Utility Commands show boardinfo led This command displays the LED status. 5.3.20 Format show boardinfo led Mode Privileged EXEC show boardinfo amc connection This command displays the connections to an AMC carrier. 5.3.21 Format show boardinfo amc connection {amcb1|amcb2} show boardinfo amc connection all Mode Privileged EXEC show boardinfo amc fru This command displays various FRU (field replaceable unit) related information (or all FRU information) for a specified AMC. 5.3.
Utility Commands 5.3.25 AT8904M show boardinfo memory-usage This command displays the memory usage. It shows malloc and kernel statistics as well as system memory usage statistics 5.4 Format show boardinfo memory-usage Mode Priviliged EXEC Logging Commands This section describes the commands you use to configure system logging, and to view logs and the logging settings. 5.4.1 logging buffered This command enables logging to an in-memory log that keeps up to 128 logs. 5.4.1.
AT8904M Utility Commands Mode 5.4.3.1 Global Config no logging cli-command This command disables the CLI command Logging feature. 5.4.4 Format no logging cli-command Mode Global Config logging console This command enables logging to the console. You can specify the value as either an integer from 0 to 7 or symbolically through one of the following keywords: emergency (0), alert (1), critical (2), error (3), warning (4), notice (5), info (6), or debug (7). 5.4.4.
Utility Commands 5.4.7.1 AT8904M Default 514 Format logging port Mode Global Config no logging port This command resets the local logging port to the default. 5.4.8 Format no logging port Mode Global Config logging syslog This command enables syslog logging. The parameter is an integer with a range of 1-65535. 5.4.8.1 Default disabled Format logging syslog [port ] Mode Global Config no logging syslog This command disables syslog logging. 5.4.
AT8904M 5.4.10 Utility Commands show logging buffered This command displays buffered logging (system startup and system operation logs). Format show logging buffered Mode Privileged EXEC Buffered (In-Memory) Logging Shows whether the In-Memory log is enabled or disabled. Buffered Logging Wrapping Behavior The behavior of the In Memory log when faced with a log full situation. Buffered Log Count The count of valid entries in the buffered log. 5.4.
Utility Commands 5.5 AT8904M Format show logging backtrace Mode Privileged EXEC System Utility and Clear Commands This section describes the commands you use to help troubleshoot connectivity issues and to restore various configurations to their factory defaults. 5.5.1 traceroute Use the traceroute command to discover the routes that packets actually take when traveling to their destination through the network on a hop-by-hop basis. The value should be a valid IP address.
AT8904M Utility Commands Mode 5.5.6 Privileged EXEC clear port-channel This command clears all port-channels (LAGs). 5.5.7 Format clear port-channel Mode Privileged EXEC clear traplog This command clears the trap log. 5.5.8 Format clear traplog Mode Privileged EXEC clear vlan This command resets VLAN configuration parameters to the factory defaults. 5.5.9 Format clear vlan Mode Privileged EXEC clear board event-log This command deletes all event-log records 5.5.
Utility Commands Mode 5.5.12.1 AT8904M Privileged EXEC no set bootstopkey This command resets the bootstop key. The boot process can not be interrupted. 5.5.13 Format no set bootstopkey Mode Privileged EXEC ping This command checks if another computer is on the network and listens for connections. To use this command, configure the switch for network (in-band) connection. The source and target devices must have the ping utility enabled and running on top of TCP/IP.
AT8904M Utility Commands {xmodem | tftp:////} For TFTP, the parameter is the IP address of the server, is the path to the file, and is the name of the file you want to upload or download. Table 1. Copy Parameters Source 5.6 Destination Description nvram:clibanner Copies the CLI banner to a server. nvram:errorlog Copies the error log file to a server. nvram:log Copies the log file to a server.
Utility Commands 5.6.1 AT8904M license advanced This command enables a particular feature. This command also enables the corresponding show commands for a feature. NOTE: If the feature is enabled, the feature is visible in the output of the show running-config command. The parameter specifies the hexadecimal key for the feature. 5.6.1.1 Default none Format license advanced Mode Privileged EXEC no license advanced This command disables a particular feature.
AT8904M Utility Commands Mode 5.7.2 Global Config sntp client mode This command enables Simple Network Time Protocol (SNTP) client mode and may set the mode to either broadcast or unicast. 5.7.2.1 Default disabled Format sntp client mode [broadcast | unicast] Mode Global Config no sntp client mode This command disables Simple Network Time Protocol (SNTP) client mode. 5.7.
Utility Commands 5.7.5.1 AT8904M Default 5 Format sntp unicast client poll-timeout Mode Global Config no sntp unicast client poll-timeout This command will reset the poll timeout for SNTP unicast clients to its default value. 5.7.6 Format no sntp unicast client poll-timeout Mode Global Config sntp unicast client poll-retry This command will set the poll retry for SNTP unicast clients to a value from 0 to 10. 5.7.6.
AT8904M 5.7.8.1 Utility Commands no sntp server This command deletes an server from the configured SNTP servers. 5.7.9 Format no sntp server remove Mode Global Config show sntp This command is used to display SNTP settings and status. Format show sntp Mode Privileged EXEC Last Update Time Time of last clock update. Last Attempt Time Time of last transmit query (in unicast mode).
Utility Commands AT8904M Server Maximum Entries Total number of SNTP Servers allowed. Server Current Entries Total number of SNTP configured. For each configured server: IP Address IP address of configured SNTP Server. Address Type Address Type of configured SNTP server. Priority IP priority type of the configured server. Version SNTP Version number of the server. The protocol version used to query the server in unicast mode.
AT8904M 5.8.2.1 Utility Commands Default none Format client-identifier Mode DHCP Pool Config no client-identifier This command deletes the client identifier. 5.8.3 Format no client-identifier Mode DHCP Pool Config client-name This command specifies the name for a DHCP client. Name is a string consisting of standard ASCII characters. 5.8.3.1 Default none Format client-name Mode DHCP Pool Config no client-name This command removes the client name. 5.8.
Utility Commands Mode 5.8.5.1 AT8904M DHCP Pool Config no dns-server This command removes the DNS Server list. 5.8.6 Format no dns-server Mode DHCP Pool Config hardware-address This command specifies the hardware address of a DHCP client. Hardware-address is the MAC address of the hardware platform of the client consisting of 6 bytes in dotted hexadecimal format. Type indicates the protocol of the hardware platform. It is 1 for 10 MB Ethernet and 6 for IEEE 802. 5.8.6.
AT8904M 5.8.8.1 Utility Commands Default 1 (day) Format lease [{ [] [] | infinite}] Mode DHCP Pool Config no lease This command restores the default value of the lease time for DHCP Server. 5.8.9 Format no lease Mode DHCP Pool Config network (DHCP Pool Config) Use this command to configure the subnet number and mask for a DHCP address pool on the server. Network-number is a valid IP address, made up of four decimal bytes ranging from 0 to 255. IP address 0.0.0.
Utility Commands 5.8.11.1 AT8904M no domain-name This command removes the domain name. 5.8.12 Format no domain-name Mode DHCP Pool Config netbios-name-server This command configures NetBIOS Windows Internet Naming Service (WINS) name servers that are available to DHCP clients. One IP address is required, although one can specify up to eight addresses in one command line.
AT8904M 5.8.14.1 Utility Commands Default inbound interface helper addresses Format next-server
Mode DHCP Pool Config no next-server This command removes the boot server list. 5.8.15 Format no next-server Mode DHCP Pool Config option The option command configures DHCP Server options. The parameter specifies the DHCP option code and ranges from 1-254. The parameter specifies an NVT ASCII character string.Utility Commands Mode 5.8.17 AT8904M Global Config ip dhcp ping packets Use this command to specify the number, in a range from 2-10, of packets a DHCP server sends to a pool address as part of a ping operation. By default the number of packets sent to a pool address is 2, which is the smallest allowed number when sending packets. Setting the number of packets to 0 disables this command. 5.8.17.
AT8904M Utility Commands Mode 5.8.20 Global Config ip dhcp conflict logging This command enables conflict logging on DHCP server. 5.8.20.1 Default enabled Format ip dhcp conflict logging Mode Global Config no ip dhcp conflict logging This command disables conflict logging on DHCP server. 5.8.21 Format no ip dhcp conflict logging Mode Global Config clear ip dhcp binding This command deletes an automatic address binding from the DHCP server database.
Utility Commands IP address AT8904M The IP address of the client. Hardware Address The MAC address or the client identifier. Lease expiration The lease expiration time of the IP address assigned to the client. Type 5.8.25 The manner in which IP address was assigned to the client. show ip dhcp global configuration This command displays address bindings for the specific IP address on the DHCP server. If no IP address is specified, the bindings corresponding to all the addresses are displayed.
AT8904M Utility Commands Host 5.8.27 The IP address and the mask for a manual binding to a DHCP client. show ip dhcp server statistics This command displays DHCP server statistics. Format show ip dhcp server statistics Modes Privileged EXEC User EXEC Automatic Bindings The number of IP addresses that have been automatically mapped to the MAC addresses of hosts that are found in the DHCP database. Expired Bindings The number of expired leases.
Utility Commands 5.9 AT8904M DHCP Filtering You can configure the DHCP Filtering feature as a security measure against unauthorized DHCP servers. DHCP filtering works by allowing you to configure each port as either a trusted port or an untrusted port. To optimize the DHCP filtering feature, configure the port that is connected to an authorized DHCP server on your network as a trusted port. Any DHCP responses received on a trusted port are forwarded.
AT8904M Utility Commands 5.10 Enhanced Port-Channel / LAG and Multicast Commands 5.10.1 port-channel hash multicast This command configures the multicast hash algorithm. The command allows the user to globally select the hash algorithm used for distribution of NUC (Non Unicast) traffic. This includes broadcast and multicast traffic, as well as unicast traffic to unknown destination MAC address (DLF, flooded).
Utility Commands 5.10.5 AT8904M port-channel hash unicast enhanced This command configures enhanced unicast hash algorithm. On extension fabric, a new, enhanced hashing algorithm can be selected for distributing incoming traffic over an egress port-channel/LAG. This enhanced mode is different from basic modes (above) and allows distribution of packets based on L2-L4 criteria, in addition for supporting new IP encapsulations.
AT8904M 5.10.5.1 Utility Commands no port-channel hash unicast enhanced This command disables enhanced unicast hash algorithm on the extension fabric interface. 5.10.
Utility Commands 5.10.9 AT8904M show vlan multicast This command displays the VLAN based multicast handling. The command displays for a specified VLAN ID (range is 1-4094) or all created VLANs (inclusive default VLAN) the multicast flooding settings. The displayed fields are • • • 5.11 the VLAN Identifier (VID) associated with each VLAN the VLAN type (default, static or dynamic) the multicast flooding, indicating whether a packet with unregistered multicast address should be flooded or not (yes/no).
AT8904M 5.11.3 Utility Commands debug spanning-tree bpdu transmit This command enables tracing of spanning tree BPDUs transmitted by the switch. Spanning tree should be enabled on the device and on the interface in order to monitor packets on a particular interface. Default disabled Format debug spanning-tree bpdu transmit Mode Privileged EXEC A sample output of the trace message is shown below. <15> JAN 01 01:02:04 192.168.17.29-1 DOT1S[191096896]: dot1s_debug.
Utility Commands AT8904M RX A packet received by the device. Intf The interface that the packet came in on. Format used is port/slot (internal interface number). Source_Mac Source MAC address of the packet. Version Spanning tree protocol version (0-3). 0 refers to STP, 2 RSTP and 3 MSTP. Root_Mac MAC address of the CIST root bridge. Root_Priority Priority of the CIST root bridge. The value is between 0 and 61440. It is displayed in hex in multiples of 4096. Path_Cost 5.11.4.
AT8904M 5.11.6.1 Utility Commands Intf The interface that the packet went out on. Format used is slot/port (internal interface number). Src_Mac Source MAC address of the packet. Dest_Mac Destination multicast MAC address of the packet. Src_IP The source IP address in the IP header in the packet. Dest_IP The destination multicast IP address in the packet. Type The type of IGMP packet.
Utility Commands AT8904M V3_Membership_Report – IGMP Version 3 Membership Report V2_Leave_Group – IGMP Version 2 Leave Group Group 5.11.7.1 Multicast group address in the IGMP header. no debug igmpsnooping receive This command disables tracing of received IGMP Snooping packets. 5.11.8 Format no debug igmpsnooping receive Mode Privileged EXEC debug igmpsnooping packet This command enables tracing of IGMP Snooping packets received and transmitted by the switch. 5.11.8.
AT8904M Utility Commands Type 5.11.9.1 Type determines whether or not the ICMP message is a REQUEST or a RESPONSE. no debug ping packet This command disables tracing of ICMP echo requests and responses. 5.11.10 Format no debug ping packet Mode Privileged EXEC debug rip packet This command turns on tracing of RIP requests and responses. This command takes no options. The output is directed to the log file.
Utility Commands 5.11.10.1 AT8904M no debug rip packet This command disables tracing of RIP requests and responses. 5.11.11 Format no debug rip packet Mode Privileged EXEC debug ospf packet This command enables tracing of OSPF packets received and transmitted by the switch. Default disabled Format debug ospf packet Mode Privileged EXEC Sample outputs of the trace messages are shown below. <15> JAN 02 11:03:31 10.50.50.1-2 OSPF[46300472]: ospf_debug.
AT8904M Utility Commands The remaining fields in the trace are specific to the type of OSPF Packet. HELLO packet field definitions: Netmask The netmask in the hello packet. DesignRouter Designated Router IP address. Backup Backup router IP address. DB_DSCR packet field definitions: MTU MTU Options Options in the OSPF packet. Flags Could be one or more of the following: I – Init M – More MS – Master/Slave Seq Sequence Number of the DD packet.
Utility Commands AT8904M A sample output of the trace message is shown below. <15> JAN 01 14:04:51 10.254.24.31-1 DOT3AD[183697744]: dot3ad_debug.c(385) 58 %% Pkt TX - Intf: 1/0/1(1), Type: LACP, Sys: 00:11:88:14:62:e1, State: 0x47, Key: 0x36 5.11.12.1 no debug lacp packet This command disables tracing of LACP packets.
AT8904M Chapter 1 6 Management Commands Page 6 - 1 AT8904M CLI Reference Manual
Management Commands 6. AT8904M Management Commands This chapter describes the management commands available in the CLI. The Management Commands chapter contains the following sections: • • • • • • • • • • • • • 6.1 “Network Interface Commands” on page 6 - 2 6.2 “Console Port Access Commands” on page 6 - 5 6.3 “Telnet Commands” on page 6 - 7 6.4 “Secure Shell (SSH) Command” on page 6 - 11 6.5 “User Account Commands” on page 6 - 13 6.6 “SNMP Commands” on page 6 - 16 6.
AT8904M 6.1.3 Management Commands serviceport protocol This command specifies the network management port configuration protocol. If you modify this value, the change is effective immediately. If you use the bootp parameter, the switch periodically sends requests to a BootP server until a response is received. If you use the dhcp parameter, the switch periodically sends requests to a DHCP server until a response is received.
Management Commands Mode 6.1.7.1 AT8904M Privileged EXEC no network mac-type This command resets the value of MAC address to its default. 6.1.8 Format no network mac-type Mode Privileged EXEC network bind (extension fabric only) This command allows the user to configure the extension fabric for management through the basic interface. I.e. SNMP, TELNET and SSH access will be possible through the same network management VLAN and subnet that is configured on the base fabric.
AT8904M Management Commands The IP address of the interface. The factory default value is 0.0.0.0 Subnet Mask The IP subnet mask for this interface. The factory default value is 0.0.0.0 Default Gateway The default gateway for this IP interface. The factory default value is 0.0.0.0 Burned In MAC Address The burned in MAC address used for in-band connectivity. Locally Administered MAC Address If desired, a locally administered MAC address can be configured for in-band connectivity.
Management Commands AT8904M the Global Config mode, you can enter other command modes, including Line Config mode. 6.2.2 Format configuration Mode Privileged EXEC lineconfig This command gives you access to the Line Config mode, which allows you to configure various Telnet settings and the console port. 6.2.3 Format lineconfig Mode Global Config serial baudrate This command specifies the communication rate of the terminal interface.
AT8904M Management Commands Serial Port Login Timeout (minutes) The time, in minutes, of inactivity on a Serial port connection, after which the Switch will close the connection. Any numeric value between 0 and 160 is allowed, the factory default is 5. A value of 0 disables the timeout. Baud Rate (bps) The default baud rate at which the serial port will try to connect. The available values are 1200, 2400, 4800, 9600, 19200, 38400,57600, and 115200 baud. The factory default is 9600 baud.
Management Commands 6.3.3 AT8904M transport input telnet This command regulates new Telnet sessions. If enabled, new Telnet sessions can be established until there are no more sessions available. An established session remains active until the session is ended or an abnormal network error ends the session. NOTE: If the Telnet Server Admin Mode is disabled, Telnet sessions cannot be established. Use the ip telnet server enable command to enable Telnet Server Admin Mode. 6.3.3.
AT8904M 6.3.6 Management Commands session-timeout This command sets the Telnet session timeout value.The timeout value unit of time is minutes. A value of 0 indicates that a session remains active indefinitely. 6.3.6.1 Default 0 Format session-timeout Mode Line Config <0-160> no session-timeout This command sets the Telnet session timeout value to the default. The timeout value unit of time is minutes. 6.3.
Management Commands AT8904M NOTE: Changing the timeout value for active sessions does not become effective until the session is reaccessed. Also, any keystroke activates the new timeout duration. 6.3.9 Format no telnetcon timeout Mode Privileged EXEC disconnect Use the disconnect command to close Telnet or SSH sessions. Use all to close all Telnet and SSH sessions, or use to specify the session ID to close. To view the possible values for , use the show loginsession command.
AT8904M Management Commands User EXEC Remote Connection Login Timeout (minutes) This object indicates the number of minutes a remote connection session is allowed to remain inactive before being logged off. May be specified as a number from 1 to 160. The factory default is 5. Maximum Number of Remote Connection Sessions This object indicates the number of simultaneous remote connection sessions allowed. The factory default is 5.
Management Commands 6.4.3.1 AT8904M no ip ssh server enable This command disables the IP secure shell server. 6.4.4 Format no ip ssh server enable Mode Privileged EXEC sshcon maxsessions This command specifies the maximum number of SSH connection sessions that can be established. A value of 0 indicates that no ssh connection can be established. The range is 0 to 5. 6.4.4.
AT8904M Management Commands Administrative Mode This field indicates whether the administrative mode of SSH is enabled or disabled. Protocol Level The protocol level may have the values of version 1, version 2 or both versions 1 and version 2. Connections This field specifies the current SSH connections. 6.5 User Account Commands This section describes the commands you use to add, manage, and delete system users. FASTPATH software has two default users: admin and guest.
Management Commands 6.5.2.1 AT8904M Default no password Format users passwd Mode Global Config no users passwd This command sets the password of an existing user to blank. When you change a password, a prompt asks for the old password. If there is no password, press enter. 6.5.3 Format no users passwd Mode Global Config users snmpv3 accessmode This command specifies the snmpv3 access privileges for the specified login user.
AT8904M 6.5.4.1 Management Commands no users snmpv3 authentication This command sets the authentication protocol to be used for the specified user to none. The is the user name for which the specified authentication protocol is used. 6.5.5 Format no users snmpv3 authentication Mode Global Config users snmpv3 encryption This command specifies the encryption protocol used for the specified user. The valid encryption protocols are des or none.
Management Commands AT8904M retrieve parameter information. The SNMPv3 access mode may be different than the CLI and Web access mode. SNMPv3 Authentication The authentication protocol to be used for the specified login user. SNMPv3 Encryption The encryption protocol to be used for the specified login user. 6.6 SNMP Commands This section describes the commands you use to configure Simple Network Management Protocol (SNMP) on the switch.
AT8904M Management Commands Otherwise, this value is ANDed with the mask to determine the range of allowed client IP addresses. The name is the applicable community name. 6.6.3.1 Default 0.0.0.0 Format snmp-server community ipaddr Mode Global Config no snmp-server community ipaddr This command sets a client IP address for an SNMP community to 0.0.0.0. The name is the applicable community name. 6.6.
Management Commands 6.6.5.1 AT8904M no snmp-server community mode This command deactivates an SNMP community. If the community is disabled, no SNMP requests using this community are accepted. In this case the SNMP manager associated with this community cannot manage the switch until the Status is changed back to Enable. 6.6.6 Format no snmp-server community mode Mode Global Config snmp-server community ro This command restricts access to switch information.
AT8904M 6.6.9.1 Management Commands no snmp-server enable traps This command disables the Authentication Flag. 6.6.10 Format no snmp-server enable traps Mode Global Config snmp-server enable traps bcaststorm This command enables the broadcast storm trap. When enabled, broadcast storm traps are sent only if the broadcast storm recovery mode setting associated with the port is enabled. 6.6.10.
Management Commands 6.6.12.1 AT8904M no snmp-server enable traps multiusers This command disables Multiple User traps. 6.6.13 Format no snmp-server enable traps multiusers Mode Global Config snmp-server enable traps stpmode This command enables the sending of new root traps and topology change notification traps. 6.6.13.
AT8904M Management Commands NOTE: This command does not support a “no” form. 6.6.16 Default snmpv2 Format snmptrap snmpversion Mode Global Config snmptrap ipaddr This command assigns an IP address to a specified community name. The maximum length of name is 16 case-sensitive alphanumeric characters. NOTE: IP addresses in the SNMP trap receiver table must be unique. If you make multiple entries using the same IP address, the first entry is retained and processed.
Management Commands 6.6.19 AT8904M snmp trap link-status all This command enables link status traps for all interfaces. NOTE: This command is valid only when the Link Up/Down Flag is enabled. See 6.6.11 “snmp-server enable traps linkmode” on page 6 - 19 6.6.19.1 Format snmp trap link-status all Mode Global Config no snmp trap link-status all This command disables link status traps for all interfaces. NOTE: This command is valid only when the Link Up/Down Flag is enabled. See 6.6.
AT8904M 6.6.21 Management Commands show snmptrap This command displays SNMP trap receivers. Trap messages are sent across a network to an SNMP Network Manager. These messages alert the manager to events occurring within the switch or on the network. Six trap receivers are simultaneously supported. Format show snmptrap Privileged EXEC SNMP Trap Name The community string of the SNMP trap packet sent to the trap manager. The string is case sensitive and can be up to 16 alphanumeric characters.
Management Commands 6.7.1 AT8904M logging cli-command This command enables the CLI command logging feature, which enables the FASTPATH software to log all CLI commands issued on the system. 6.7.1.1 Default enabled Format logging cli-command Mode Global Config no logging cli-command This command disables the CLI command Logging feature. 6.
AT8904M Management Commands remove it from the configuration. The IP address you specify must match that of a previously configured accounting server. If you use the optional parameter, the command configures the UDP port to use when connecting to the RADIUS accounting server. If a is already configured for the accounting server, the new replaces the previously configured . The must be a value in the range 1 - 65535, with 1813 being the default.
Management Commands 6.8.5 AT8904M radius server primary This command is used to configure the primary RADIUS authentication server for this RADIUS client. The primary server handles RADIUS requests. The remaining configured servers are only used if the primary server cannot be reached. You can configure up to three servers on each client. Only one of these servers can be configured as the primary.
AT8904M Management Commands [servers] Mode Privileged EXEC Primary Server IP Address The configured server currently in use for authentication. Number of configured servers The configured IP address of the authentication server. Max number of retransmits The configured value of the maximum number of times a request packet is retransmitted. Timeout Duration The configured timeout value, in seconds, for request re-transmissions. Accounting Mode Yes or No.
Management Commands AT8904M The number of RADIUS packets received on the accounting port from this server. Malformed Responses The number of malformed RADIUS Accounting-Response packets received from this server. Malformed packets include packets with an invalid length. Bad authenticators and unknown types are not included as malformed accounting responses. Bad Authenticators The number of RADIUS Accounting-Response packets containing invalid authenticators received from this accounting server.
AT8904M Management Commands attributes or unknown types are not included as malformed access responses. Bad Authenticators The number of RADIUS Access-Response packets containing invalid authenticators or signature attributes received from this server. Pending Requests The number of RADIUS Access-Request packets destined for this server that have not yet timed out or received a response. Timeouts The number of authentication timeouts to this server.
Management Commands 6.9.2.1 AT8904M no tacacs-server key Use the no tacacs-server key command to disable the authentication and encryption key for all TACACS+ communications between the switch and the TACACS+ daemon. The parameter has a range of 0 - 128 characters This key must match the key used on the TACACS+ daemon. 6.9.
AT8904M Management Commands Default 0 Format priority Mode 6.9.7 TACACS Config timeout Use the timeout command in TACACS Configuration mode to specify the timeout value in seconds. If no timeout value is specified, the global value is used. The parameter has a range of 1-30 and is the timeout value in seconds. Format Mode 6.9.8 TACACS Config timeout show tacacs Use the show tacacs command to display the configuration and statistics of a TACACS+ server.
Management Commands AT8904M Any command line that begins with the “!” character is recognized as a comment line and ignored by the parser. The following lines show an example of a script: ! Script file for displaying management access show telnet !Displays the information about remote connections ! Display information about direct connections show serial ! End of the script file! NOTE: To specify a blank password for a user in the configuration script, you must specify it as a space within quotes.
AT8904M 6.10.4 Management Commands script list This command lists all scripts present on the switch as well as the remaining available space. Format script list Global Config Configuration Script Name of the script. Size Privileged EXEC Mode 6.10.5 script show This command displays the contents of a script file, which is named . Mode Privileged EXEC Output Format line : Format 6.10.
Management Commands AT8904M 6.12 Bootcycle commands 6.12.1 show boardinfo bootcycle This command displays whether a bootcycle-detection is activated and (if activated) the related parameters. 6.12.2 Format show boardinfo bootcycle Mode Priviliged Exec set board bootcycle This command activates/deactivates a bootcycle-detection and (if activated) sets the related parameters. Parameter ‘none’ deactivates the bootcycle detection.
AT8904M Management Commands Mode 6.13.2 Privileged EXEC show watchdog This command displays the watchdog settings. It displays the values (or string “disabled”) of different watchdog (during BIST, during loading of kernel and INITRD, during startup of switching application and during normal execution of switching application) and the heartbeat of the fpmux application.
Management Commands AT8904M CLI Reference Manual AT8904M Page 6 - 36
AT8904M Appendix A Getting Help Page A - 1 AT8904M CLI Reference Manual
Getting Help A. AT8904M Getting Help If at any time you encounter difficulties with your application or with any of our products, or if you simply need guidance on system setups and capabilities, contact our Technical Support at: North America EMEA Tel.: (450) 437-5682 Tel.: +49 (0) 8341 803 xxx Fax: (450) 437-8053 Fax: +49 (0) 8341 803 xxx If you have any questions about Kontron, our products, or services, visit our Web site at: www.kontron.
AT8904M Getting Help RETURNING DEFECTIVE MERCHANDISE Before returning any merchandise please do one of the following if your product malfunctions: • Call 1. Call our Technical Support department in North America at (450) 437-5682 and in EMEA at +49 (0) 8341 803 xxx. Make sure you have the following on hand: our Invoice #, your Purchase Order #, and the Serial Number of the defective unit. 2.
Getting Help AT8904M WHEN RETURNING A UNIT • In the box, you have to include the name and telephone number of a person whom we can contact for further explanations if necessary when returning goods. Where applicable, always include all duty papers and invoice(s) associated with the item(s) in question. • Ensure that the unit is properly packed. Pack it in a rigid cardboard box. • Clearly write or mark the RMA number on the outside of the package you are returning. • Ship prepaid.
Return to Manufacturer Authorization Request Contact Name: __________________________________________________________ Company Name: __________________________________________________________ Street Address: __________________________________________________________ City: ________________________ Province/State: Country: ________________________ Postal/Zip Code: _______________________ Phone Number: ________________________ Extension: _______________________ Fax Number: ______________________
Getting Help AT8904M CLI Reference Manual AT8904M Page A - 6
AT8904M Appendix B List of Commands AT8904M CLI Reference Manual
List of Commands B. AT8904M List of Commands {deny | permit} ................................................................................................................. 4 - 24 1583compatibility ............................................................................................................ 3 - 25 access-list ......................................................................................................................... 4 - 27 acl-trapflags .....................................
AT8904M List of Commands classofservice ip-dscp-mapping .......................................................................................... 4 - 3 classofservice trust ..............................................................................................................4 - 3 clear arp-cache ....................................................................................................................3 - 5 clear board event-log ............................................................
List of Commands AT8904M default-router .................................................................................................................... 5 - 33 deleteport (Global Config) ............................................................................................... 2 - 53 deleteport (Interface Config) ............................................................................................ 2 - 53 description ..........................................................................
AT8904M List of Commands host ...................................................................................................................................5 - 34 hostroutesaccept ...............................................................................................................3 - 51 interface .............................................................................................................................. 2 - 2 ip access-group ................................................
List of Commands AT8904M ip vrrp authentication ....................................................................................................... 3 - 18 ip vrrp ip ........................................................................................................................... 3 - 18 ip vrrp mode ..................................................................................................................... 3 - 18 ip vrrp preempt .......................................................
AT8904M List of Commands match protocol ..................................................................................................................4 - 12 match secondary-cos ........................................................................................................4 - 10 match secondary-vlan .......................................................................................................4 - 14 match source-address mac ..............................................................
List of Commands AT8904M no arp resptime no arp retries no arp timeout no authentication login no auto-negotiate no auto-negotiate all no auto-summary no bootfile no bootpdhcprelay cidoptmode no bootpdhcprelay enable no bootpdhcprelay maxhopcount no bootpdhcprelay minwaittime no bootpdhcprelay serverip no bridge aging-time no class no class-map no classofservice dot1p-mapping no classofservice ip-dscp-mapping no classofservice trust no client-identifier no client-name no cos-queue min-bandwidth no cos-que
AT8904M List of Commands no dos-control firstfrag no dos-control icmp no dos-control l4port no dos-control sipdip no dos-control tcpflag no dos-control tcpfrag no dot1x max-req no dot1x port-control no dot1x port-control all no dot1x re-authentication no dot1x system-auth-control no dot1x timeout no dot1x user no dvlan-tunnel etherType no ekeying no enable (OSPF) no enable (RIP) no exit-overflow-interval no external-lsdb-limit no hardware-address no host no hostroutesaccept no ip access-group no ip addres
List of Commands AT8904M no ip ospf priority no ip ospf retransmit-interval no ip ospf transmit-delay no ip proxy-arp no ip rip no ip rip authentication no ip rip receive version no ip rip send version no ip route no ip route default no ip route distance no ip routing no ip ssh no ip ssh server enable no ip telnet server enable no ip vrrp no ip vrrp no ip vrrp authentication no ip vrrp ip no ip vrrp mode no ip vrrp preempt no ip vrrp priority no ip vrrp timers advertise no lease no license advanced no lld
AT8904M List of Commands no mode dot1q-tunnel 2 - 28 no mode dvlan-tunnel 2 - 28 no monitor ........................................................................................................................
List of Commands AT8904M no set gmrp interfacemode no set gvrp adminmode no set gvrp interfacemode no set igmp no set igmp fast-leave no set igmp groupmembership-interval no set igmp interfacemode no set igmp maxresponse no set igmp mcrtexpiretime no set igmp mrouter no set igmp mrouter interface no shutdown no shutdown all no snmp trap link-status no snmp trap link-status all no snmp-server community no snmp-server community ipaddr no snmp-server community ipmask no snmp-server community mode no snmp-ser
AT8904M List of Commands no spanning-tree mst priority no spanning-tree mst vlan no spanning-tree port mode no spanning-tree port mode all no split-horizon no sshcon maxsessions no sshcon timeout no storm-control broadcast no storm-control broadcast all no storm-control broadcast all level no storm-control broadcast level no storm-control flowcontrol no storm-control multicast no storm-control multicast all no storm-control multicast all level no storm-control multicast level no storm-control unicast no s
List of Commands AT8904M no vlan protocol group add protocol 2 - 22 no vlan pvid 2 - 24 no vlan routing 3 - 16 no vlan tagging 2 - 24 option ............................................................................................................................... 5 - 37 ping .................................................................................................................................. 5 - 26 police-simple .............................................................................
AT8904M List of Commands script apply nointerl.scr ....................................................................................................6 - 32 script delete ....................................................................................................................... 6 - 32 script list ...........................................................................................................................6 - 33 script show .........................................................
List of Commands AT8904M show boardinfo amc connection ...................................................................................... 5 - 19 show boardinfo amc fru ................................................................................................... 5 - 19 show boardinfo amc ipmidev ........................................................................................... 5 - 19 show boardinfo bootcycle ................................................................................
AT8904M List of Commands show ip dhcp binding ........................................................................................................5 - 39 show ip dhcp conflict ........................................................................................................5 - 41 show ip dhcp filtering .......................................................................................................5 - 42 show ip dhcp global configuration .....................................................
List of Commands AT8904M show logging buffered ..................................................................................................... 5 - 23 show logging hosts ........................................................................................................... 5 - 23 show logging traplogs ...................................................................................................... 5 - 23 show loginsession ......................................................................
AT8904M List of Commands show spanning-tree vlan ...................................................................................................2 - 17 show startupconfig ..............................................................................................................5 - 4 show storm-control ...........................................................................................................2 - 51 show switchport protected .............................................................
List of Commands AT8904M sntp unicast client poll-interval ........................................................................................ 5 - 29 sntp unicast client poll-retry ............................................................................................. 5 - 30 sntp unicast client poll-timeout ........................................................................................ 5 - 29 spanning-tree ................................................................................
AT8904M List of Commands telnetcon timeout ................................................................................................................6 - 9 timeout .............................................................................................................................. 6 - 31 timers spf .......................................................................................................................... 3 - 37 traceroute .......................................................
