» Kontron User's Guide « CP-RIO6-923 Document Revision 1.2 Document ID: CP-RIO6-923 Issue Date: April 2011 If it's embedded, it's Kontron. www.kontron.
Revision History Rev. Index Brief Description of Changes Date of Issue 1.0 Initial Issue 12 September 2007 1.1 Minor changes in chapter 1, 2 and 3 19 September 2007 1.2 Minor changes in chapter 1 and 3 related to the three variants available 27 April 2011 Customer Service Contact Information: Kontron Canada, Inc. 4555 Ambroise-Lafortune Boisbriand, Québec, Canada J7H 0A4 Tel: (450) 437-5682 (800) 354-4223 Fax: (450) 437-8053 E-mail: support@ca.kontron.
Table of Contents Revision History .................................................................................................................. ii Customer Service ................................................................................................................ ii Proprietary Note .................................................................................................................vi Trademarks ..................................................................................
List of Tables Table 1-1: CP-RIO6-923 Main Specifications ................................................................... 3 Table 3-1: Ethernet Port Mapping ................................................................................ 9 Table 3-2: RJ45 Pin Assignment ................................................................................. 10 Table 3-3: RS232 Pin Assignment ...............................................................................
List of Figures Figure 3-1: Functional Block Diagram ...............................................................................9 Figure 3-2: CP-RIO6-923 single-slot front panel ................................................................. 16 Figure 3-3: CP-RIO6-923 dual-slot front panel ................................................................... 16 v CP-RIO6-923 User Guide www.kontron.
Preface Proprietary Note This document contains information proprietary to Kontron AG. It may not be copied or transmitted by any means, disclosed to others, or stored in any retrieval system or media without the prior written consent of Kontron AG or one of its authorized agents. The information contained in this document is, to the best of our knowledge, entirely correct.
Preface Before you Begin Before handling the board, read the instructions and safety guidelines on the following pages to prevent damage to the product and to ensure your own personal safety. Refer to the "Advisory Conventions" section for advisory conventions used in this user's guide, including the distinction between Warnings, Cautions and Notes. • Always use caution when handling/operating the computer.
Preface When Working Inside a Computer Before taking covers off a computer, perform the following steps: • Turn off the computer and any peripherals. • Disconnect the computer and peripherals from power sources or subsystems to prevent electric shock or system board damage. This does not apply to when hot-swapping parts. • Disconnect telephone or telecommunications lines from the computer.
Preface Advisory Conventions CAUTION This symbol and title indicate potential damage to hardware and tells you how to avoid the problem. CAUTION Electric Shock This symbol and title warn of hazards due to electrical shocks (> 60V) when touching products or parts of them. Failure to observe the precautions indicated and/or prescribed by the law may endanger your life/health and/or result in damage to your material.
Preface Safety Instructions Your new Kontron product was developed and tested carefully to provide all features necessary to ensure its compliance with electrical safety requirements. It was also designed for a long fault-free life. However, the life expectancy of your product can be drastically reduced by improper treatment during unpacking and installation.
Preface Special Handling and Unpacking Instructions ESD Sensitive Device This symbol and title inform that electronic boards and their components are sensitive to static electricity. Therefore, care must be taken during all handling operations and inspections of this product, in order to ensure product integrity at all times. Unpacking Follow these recommendations while unpacking: • Remove all items from the box.
Preface Make sure your system provides the minimum DC voltages required at the board's slot, especially if DC power is carried by cables. If you are still not able to get your board running, contact our Technical Support for assistance. Storing the Boards Electronic boards are sensitive devices. Do not handle or store device near strong electrostatic, electromagnetic, magnetic or radioactive fields.
Preface Regulatory Compliance Statements FCC Compliance Statement for Class B Devices This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface Two Year Warranty Kontron AG grants the original purchaser of Kontron’s products a TWO YEAR LIMITED HARDWARE WARRANTY as described in the following. However, no other warranties that may be granted or implied by anyone on behalf of Kontron are valid unless the consumer has the express written consent of Kontron AG. Kontron AG warrants their own products, excluding software, to be free from manufacturing and material defects for a period of 24 consecutive months from the date of purchase.
Chapter 1 Introduction 1 www.kontron.
Introduction 1 Introduction 1.1 Product Overview The CP-RIO6-923 is a PICMG 2.0 compliant 6U rear panel I/O board that can be used with PICMG 2.16 compliant switches like the CP6923 or the CP6930. It provides access to up to 24 of the switch ports that are connected to the backplane. The serial console management port (RS-232) of the CP6923 is also accessible with this RIO module. This module is intended to access the backplane ports of a PICMG 2.16 compliant switch board directly.
Introduction 1.2 Technical Specification Table 1-1: CP-RIO6-923 Main Specifications CP-RIO6-923 SPECIFICATIONS • 6U CompactPCI, Rear-panel I/O board Mechanical Temperature • 233 mm x 80 mm • Weight Dual Slot Variant: 340g • Weight Single Slot Variant: 260g • Operating: -40°C to +85°C Designed to meet or exceed the following: Humidity • Bellcore GR63, Section 4.
Chapter 2 Installation 4 www.kontron.
Installation 2 Installation The CP-RIO6-923 has been designed for easy installation. However, the following standard precautions, installation procedures, and general information must be observed to ensure proper installation and to preclude damage to the board, other system components, or injury to personnel. 2.1 Safety Requirements The following safety precautions must be observed when installing or operating the CP-RIO6-923.
Installation 2.2 Installation Procedure For installing the CP-RIO6-923, it is not required that the system is powered down or the switch board in the corresponding front slot is removed or deactivated. To install the RIO module in a system proceed as follows: 1. Ensure that the safety requirements indicated in section 2.1 are observed. WARNING Failure to comply with the instruction below may cause damage to the board or result in improper system operation.
Installation 2.3 Removal Procedure For removing the CP-RIO6-923, it is not required that the system is powered down or the switch board in the corresponding front slot is removed or deactivated. To remove the RIO module proceed as follows: 1. Ensure that the safety requirements indicated in section 2.1. are observed. WARNING Care must be taken when applying the procedures below to ensure that neither the CP-RIO6-923 nor system boards are physically damaged by the application of these procedures. 2.
Chapter 3 Hardware Description 8 www.kontron.
Hardware Description 3 Hardware Description This chapter describes the board specific features of the CP-RIO6-923. The building blocks are: • 12 or 24 1000Base-T ports • Serial RS232 console connector • CompactPCI bus connectors The RIO module does not require a power supply. There are no active components on the board. 3.
Hardware Description Table 3-1: Ethernet Port Mapping (Continued) PICMG 2.16 Backplane Port CP-RIO6-923 DualSlot Port Label CP-RIO6-923 SingleSlot Port Label FL_18 18x 18x FL_19 19x 19x FL_20 20x 20x FL_21 21x 21x FL_22 22x 22x FL_23 23x 23x CP-RIO6-923-9 Single-Slot Port Label Note that ports marked with a '-' are not available on the RIO module.
Hardware Description 3.2 Serial RS232 Interface The CP-RIO6-923 provides a serial RS232 interface via an RJ45 connector. It is labelled "COM" on the front plate. This connector is provided on the dual-slot as well as on the single-slot variant. It has the following pinning: Table 3-3: RS232 Pin Assignment Signal Pin N.C. 1 N.C. 2 TXD 3 GND 4 GND 5 RXD 6 N.C. 7 N.C.
Hardware Description 3.3 CompactPCI Bus Connectors Three daughter card connecters (rJ3, rJ4 and rJ5) are used for the connection between the CP-RIO6-923 and the backplane. • rJ3 connects FL Port 1 to FL Port 8 and FL Port f • rJ4 connects FL Port 20 to FL Port 23 and the RS232 Interface (RX/TX) • rJ5 connects FL Port 9 to FL Port 19 Connector rJ3 is not installed on the single-slot variant of the CP-RIO6-923. The cPCI connectors have the following pin assignment.
Hardware Description Table 3-6: Pin Connector J4 Pinout Row A Row B Row C Row D Row E Row F 25 FL_DA20+ FL_DA20- GND FL_DC20+ FL_DC20- GND 24 FL_DB20+ FL_DB20- GND FL_DD20+ FL_DD20- GND 23 FL_DA21+ FL_DA21- GND FL_DC21+ FL_DC21- GND 22 FL_DB21+ FL_DB21- GND FL_DD21+ FL_DD21- GND 21 FL_DA22+ FL_DA22- GND FL_DC22+ FL_DC22- GND 20 FL_DB22+ FL_DB22- GND FL_DD22+ FL_DD22- GND 19 FL_DA23+ FL_DA23- GND FL_DC23+ FL_DC23- GND 18 FL_DB23+ FL_DB23- GND FL_DD
Hardware Description Table 3-7: Pin Connector J5 Pinout Row A Row B Row C Row D Row E Row F 22 FL_DA19+ FL_DA19- GND FL_DC19+ FL_DC19- GND 21 FL_DB19+ FL_DB19- GND FL_DD19+ FL_DD19- GND 20 FL_DA18+ FL_DA18- GND FL_DC18+ FL_DC18- GND 19 FL_DB18+ FL_DB18- GND FL_DD18+ FL_DD18- GND 18 FL_DA17+ FL_DA17- GND FL_DC17+ FL_DC17- GND 17 FL_DB17+ FL_DB17- GND FL_DD17+ FL_DD17- GND 16 FL_DA16+ FL_DA16- GND FL_DC16+ FL_DC16- GND 15 FL_DB16+ FL_DB16- GND FL_DD
Hardware Description 3.4 Front Panel Elements Figure 3-1: CP-RIO6-923 single-slot front panel Figure 3-2: CP-RIO6-923 dual-slot front panel 15 CP-RIO6-923 User Guide www.kontron.
Appendix A Getting Help 1KTC5520/EATX www.kontron.
A Getting Help If, at any time, you encounter difficulties with your application or with any of our products, or if you simply need guidance on system setups and capabilities, contact our Technical Support at: North America EMEA Tel.: (450) 437-5682 Tel.: +49 (0) 8341 803 333 Fax: (450) 437-8053 Fax: +49 (0) 8341 803 339 If you have any questions about Kontron, our products, or services, visit our Web site at: www.kontron.com You also can contact us by E-mail at: North America: support@ca.kontron.
• Fax • Send us a fax at: North America (450) 437-0304, EMEA +49 (0) 8341 803 339. In the fax, you must include your name, your company name, your address, your city, your postal/zip code, your phone number and your e-mail. You must also include the serial number of the defective product and a description of the problem. • E-mail • Send us an e-mail at: RMA@ca.kontron.com in North America or at: orderprocessing@kontronmodular.com in EMEA.
