KON4817 Kosmik HV-I Instruction Manual

14
Contents
1. Definitions 14
1.1 Delivery content 14
2. Safety instructions 14
3. Basics 15
3.1 Preparing the handheld transmitter 15
3.2 Preparing the mode 15
3.3 Soft start 15
3.4 Low voltage protection 15
4. General features 16
4.1 Properties 16
4.2 Cooling and mounting 16
4.3 BEC / operation without BEC 17
4.4 Toroidal core 17
4.5 Active freewheeling circuit 17
4.6 Part load capability 17
4.7 Sensorless Commutation 17
4.8 Variable clock frequency 17
4.9 Protective functions 17
4.10 Helicopter Mode 17
4.11 Autorotation AR (Bail-out) 18
5. Connecting the cables 18
5.1 BEC cables (connection to receiver) 18
5.2 Motor cables 18
5.3 Sensor plugs 18
6. Starting 19
6.1 Table of function range for the
programmable modes 19
7. Mode programming 19
7.1 Mode 1 - APM 19
7.2 Mode 2 - Glider (with brake) 19
7.3 Mode 3 - Motor flight / Boat (without brake) 20
7.4 Mode 4 - Helicopter 20
7.5 Mode 6 - Forward / Backward 22
7.6 Mode 7 - Reverse rotation 22
7.7 Connection of the telemetry cable 23
7.8 Mode 8 - Telemetry Port 1
(only HV-I variants) 23
7.9 Mode 9 - Telemetry Port 2
(only HV-I variants) 24
7.10 Mode 10 - BEC Voltage adjustment 24
8. KONTRONIK protocol 24
9. Update 24
10. Bluetooth pairing 24
11. Logging 24
12. Troubleshooting 25
13. Technical assistance, Advice, Hotline 25
13.1 Recycling 25
13.2 Warranty 25
14 cabling 26
15. Messages and their consequences 27
1. Definitions
APM Auto-Programming-Mode
EMK Electromotive force
AR Autorotation/Bail-out
BEC Battery Eliminating Circuit to power
the receiver from the main battery)
KOSMIK KOSMIK ESC
Button control knob for mode programming
LED Active light / control
Mode Operating mode / program
Parameter variable value
Pitch Blade angle (rotor blade)
top side see picture in section 5
under side see picture in section 5
KONTRONIK programming unit
1.1 Delivery content
1. 1 x KOSMIK ESC
2. 1 x short circuit protection (including fixation)
3. 2 x BEC cable
4. 1 x Telemetry cable with JR connector
(Applies only to HV-I variants)
5. 1 x Telemetry cable with mini JST connector
(Applies only to HV-I variants)
6. 1 set battery cables
(2 pieces - red / black) one sided with wire-
terminals wired, stripped and tinned on the
7. 1 set motor cables
(3 pieces – yellow or black) one sided with
wire terminals, stripped and tinned on the
other side
8. 5 x screw (M5 x 10 mm)
9. 5 x self-retaining nut (M5)
10. 10 x washer (M5)
11. 5 x shrinking tube
12. 1 x pack of screws with COOL version
2 x pack of screws with DuoCOOL version
13. 1x cooling fan with COOL version
2x cooling fan with DuoCOOL version
2. Safety instructions
KOSMIK is a product that is designed
exclusively for RC-model operation. Under
no circumstances should the KOSMIK be
used in manned applications!
Always ensure sufficient cooling in order to
prevent overheating of the ESC. If
necessary, a heatsink is to be mounted to
the KOSMIK’s top side!
• For safety reasons, the KOSMIK is always to
be operated with a properly sized short circuit
protection within the battery circuit.
• When connecting the motor and battery to the
ESC, it is very important to keep enough safety
distance from all moving parts of the device
(such as rotors or propellers). Misuse or
electronic defects may result in an unintended
motor start. A prematurely starting motor, with
connected devices such as rotors or propellers,
may cause considerable injuries.
!
!